Your positioning of the slide while disassembling, utilizing the bench to prevent the firing pin and spring from shooting across the room, as well as the other positionings, are genius. I've watched many other vids on disassembling the slide and no one does it like you do. Thanks for showing me how to do things right.
@rz1587
4 жыл бұрын
Jason, you demonstrate and communicate your knowledge very well. The ability to clearly and simply explain is strong indication that you possess a thorough understanding of the subject. Your video tutorials are the best that I have witnessed.
@LexPhotographies
Жыл бұрын
Maybe the best method to do it I ever see ! Quick and clear explaination !
@thorkill8246
4 жыл бұрын
Good to see the right people giving instructions on guns.
@DanielWillis1982
5 жыл бұрын
This is need to know info for anyone with a 1911. This should have more views
@houston33344
4 жыл бұрын
Amazing video... so tired of all other youtubers that just ramble ramble ramble
@maxmccain8950
2 жыл бұрын
Houston, your absolutely correct. What makes these people think they need to explain something they obviously know nothing about. Peace.
@19thunderball57
5 жыл бұрын
Good, straightforward how to without the added nonsense that's all too prevalent on many vids. Thanks, Jason 👍
@bloodstorm1231
Жыл бұрын
Got a RIA 1911 9mm that fails to extract sometimes. I am going to give this a shot! Thanks for the easy walkthrough!
@ericshaw426
4 жыл бұрын
Straight and to the point with excellent technique.
@Timman57
3 жыл бұрын
I do appreciate your time. Among this video and other videos, I really should have took the time to really learn my weapon and notice what it was doing to the rounds. First I thought magazine, then feed ramp, in my opinion if some light polishing with 2000 grit and then some rem oil cant fix something, then I dont need to be touching it, but I havent cleaned or checked my extractor tension before. It hasn't had too many rounds through it, maybe 2-300 but its a cheap rock island 1911. Checked it and it was beyond tight, was biting my ammunition cases as well as scuff marks where the forward motion of the slide along with the feed ramp were carrying the brunt of the work to shove the tail end of the round into the extractor, taking bites out of the cases and scuffing them as they entered the chamber. Now, the extractor is practically straight at this point and will fall out of the slide with a gentle tap, but it passes your test here and after all the other things I tried to smoothen it up, this thing runs like a wet dream. Thanks 👍
@rickhall9284
5 жыл бұрын
That's easier way than I have seen them done in the past. Thank you.
@lildeemcdee466
6 жыл бұрын
Excellent video! Nothing left to the imagination. I've been having erratic failure to eject issues with my Desert Eagle 1911C that's been killing my time at IDPA matches. I'm going to give this a shot. Thank you for your time making the video! Very helpful!
@williamdeshon2199
2 жыл бұрын
Great vid man. I’ve fired 200 rounds out of my kimber. Custom lw. Feed jams every 3 to 4 rounds. I’ll run it
@scoopof3d
2 жыл бұрын
Did it work? I just got same one jamed on my second round and just keeps jamming.
@Bill14886
4 жыл бұрын
Great video. Much easier then other videos Ive seen. Using firing pin Channel to adjust is the difference. Nice. I'll try it next time I need to adjust.
@johnbrooks2724
4 жыл бұрын
Excellent vid! Concise and to the point. Best I've seen!
@brettgodfrey9536
2 ай бұрын
Jason, you rock! -Godfrey
@spbeckman
Жыл бұрын
Yes. Yes. Yes. Yes. Yes. Thank you for presenting this.
@leonelcasias2983
3 жыл бұрын
I like to see profetional pep do the work they make it look so easy but with good parctice we all make good work
@Vod_MacDuff
2 жыл бұрын
Recently, I've been getting failure to feed on my Citadel 1911 (Armscore), and I had suspected magazines, although I didn't used to have that issue. Going to check to see if the extractor is too tight tomorrow. Crossing my fingers, thanks for the video.
@playerzero2236
4 жыл бұрын
I had to do this with my RIA 1911 A2. It seems the armscor ammo they test with has just a slightly thicker rim than a lot of brass on the market. Making a minor adjustment got rid of my failure to feed issues.
@xmus4023
10 ай бұрын
I had just experienced FTF on my last shooting with the RIA 1911. Didn't have that on the first go around but the second time ranging. Really pissed me off. Good to know that decreasing extractor tension is the trick. I thought it was the Blazer ammo that was the issue, not the extractor. Seeing that you had this issue so long ago helps.
@DoubleDeltaHoundog
3 жыл бұрын
Putty Smart Jason I will use on my series 70 Commander It is so loose it will not hold a empty case against the breecface
@williammusser8243
6 жыл бұрын
Thanks Jason, great info!
@InlinePaul
Жыл бұрын
Awesome Video! You make it look so simple.
@abramhepp8729
4 жыл бұрын
Very professional
@someusername121
3 жыл бұрын
The part that was missing: you have too much tension if you're getting failure to strip rounds off of the magazine and the slide doesn't go in battery. Too much tension prevents the slide from being able to force the case under the extractor and you'll see the brass case edge getting "filed" flat by the extractor. It can also be due to the extractor hook needing some re-profiling so it doesn't contact the brass case as its sliding up.
@Matthew-np9fk
2 жыл бұрын
I’ve been having this exact issue with my kimber. Thanks for this comment, I’m pretty confident my extractor is too tight.
@TheDkb427
8 ай бұрын
My 1911 crushed brass cases but doesn't jamb up the gun. Hell I've only put like 500 round in it. Dunno if he said this in the video but why would you play with the extractor tension?
@teayne773
Ай бұрын
Thank you so much I'm trying to fix a FTE issue
@Super4guns
10 ай бұрын
Now that was a super demonstration thank you
@bryanmejia1844
3 жыл бұрын
Excellent video, thank you!
@kimber4573
7 жыл бұрын
One of the best videos I've seen.... Thanks. I have a Kimber 1911 45ACP and my Brass is flying everywhere, Far and wide and sometimes over my head... My friend has a different brand and they fall right at his feet, He could almost drop them all in a coffee can.. Could you give me any suggestions? If not I understand... Thanks again..
@Oldman_Taylor
Жыл бұрын
LOL, bit late. But its likely your extractor is "clocking"- the firing pin block is not fitting the extractor tightly, and the extractor is rotating to a different posting a bit after each shot. The fix is working the block, not the extractor.
@ofivenojoe
Жыл бұрын
Dame it, you did that so smooth I am subbing You are a ,45 god.
@tomnelson3362
Жыл бұрын
Jason good video, clear and straight forward. My new Colt Competition 9mm ejects rounds in all directions including at me. Could incorrect extractor tension be causing this? I don't want just buy parts blindly hoping to cure this problem.
@gergemall
5 жыл бұрын
Beautiful job, thx
@enricomandragona163
4 ай бұрын
Great explanation however start by saying that the slide is an 80 series ✌️
@ScottCooper136
Жыл бұрын
Outstanding video.
@rainerburgdorfer4017
Жыл бұрын
Excellent video
@carypeaden4147
2 жыл бұрын
Your videos are great. Thanks!
@Hudson4426
Жыл бұрын
Ima need you to come to my house and do some things for me… how’s Wednesday sound?
@alonsoar6
6 ай бұрын
Thank you so much for this information
@slice9778
Жыл бұрын
My 1911 zings an empty shell casing by my head once every mag. with a Wilson's extractor. Since it's only one case per mag, do I still need to adjust the tension? If so, more or less? Thanks for your video!
@jaybo2112ot
Жыл бұрын
Awesome video!!
@larryjones6049
5 жыл бұрын
Thanks.
@wtkmywdo
7 жыл бұрын
Thanks
@nallie10
Жыл бұрын
Excellent
@Nick87899
Жыл бұрын
Thank you
@mrflynn510
4 жыл бұрын
So, it's okay if the round moves slightly as long as it doesn't come out of the extractor's grip?
@Blakgun
11 ай бұрын
If the cartridge remains under the extractor when you rotate the slide then you are either good to go, or the extra tension is too high.
@TMcD3
Жыл бұрын
My issue is failure to go back into battery. I just had the extractor adjusted. Is this the result of too much tension on the extractor. This happens on all my magazines.
@Oldman_Taylor
Жыл бұрын
Could be. That would be consistent with the extractor is too tight.
@calvin14888
3 жыл бұрын
There's a specific tools to add or decrease tention to the extractor.
@garydeplancke
4 ай бұрын
Any advice on how to remove a firing pin stop that is stuck in place? I'm unable to move the stop on my 1911.
@TheDkb427
8 ай бұрын
My 1911 crushes brass. It doesn't jamb up the gun which is weird so does that mean I need to loosen the extractor? I'm not a 1911 guy but this seems pretty easy just dunno why you would do this?
@aidansoccer12
6 ай бұрын
This doesn’t address if your extractor is too tight.
@farklefuster6876
3 ай бұрын
How can you tell if there is too much tension on the extractor? My 10mm tosses brass ten yards back and ten yards left.
@farklefuster6876
3 ай бұрын
That is to the right
@Luis.M.Castillo
4 жыл бұрын
I'm probably good to go 🤙
@stanlucas1932
Жыл бұрын
I guess there's no such thing as having TO MUCH tension?
@serbraineer
4 жыл бұрын
I’m having a failure to extract on my Rock Island Armory tac ultra hc 9mm would this fix my issues?
@Wildwestwrangler
2 жыл бұрын
yep you're probably loose
@Wildwestwrangler
2 жыл бұрын
too loose won't extract, and too tight won't feed.
@safetactical5608
3 жыл бұрын
why do my round keep getting crushed when I chamber ?????
@Wildwestwrangler
2 жыл бұрын
extractor is too tight not allowing it to move enough to properly feed.
@SIRICKO
Жыл бұрын
Fitting A frame to slide is nothing custom.
@AnthonyCatarig
5 жыл бұрын
I canot get the firing pin hiwbdid you that i am trying not done shit.
@sajidakh
3 жыл бұрын
Been a year aince this comment...did you manage to fix your grasp on the english language or was it a drinking problem?
@bp814
3 жыл бұрын
@@sajidakh aince? And you're the one to talk?
@Wildwestwrangler
2 жыл бұрын
@@bp814 lmao!!! talk about the pot calling the kettle black!!! good call lol
Пікірлер: 74