⚠️ *Found this video super useful?* Buy Paul a coffee to say thanks: ☕ PayPal: www.paypal.me/TheEngineerinMindset
@jcortega8675
5 жыл бұрын
This is an underrated channel.
@EngineeringMindset
6 жыл бұрын
Video was re-uploaded because it was accidentally deleted
@franciscoprieto6801
4 жыл бұрын
I really like this channel. It's better than the university
@matthewzook1859
4 жыл бұрын
Thanks for the video! Very informative! I'm looking to make a dehumidifier for a lumber drying kiln. How would a traditional heat pump type system be altered to make it most effective as a dehumidifier? How cold should the evaporator get? The kiln will reach 140 degrees and I'm planning to have all of the dehumidification components inside (so the heat from operating it can heat the kiln). Any insight would be greatly appreciated. Thanks!
@esnutrisari1778
3 жыл бұрын
very usefull for design, monitoring, and analysis.. it helpful for my job
@abdullahosaf1476
2 жыл бұрын
Hello, and thank you for the wonderful content can this software be used to design a hydronic system with 3 branches, each having two coils in them? Waiting for your kind response.
@kmutech718
6 жыл бұрын
sir your videos are too good can you please upload plumbing calculation design such as savage and public health plumbing for high rise building
@nsalam
10 ай бұрын
Is the a app version of this software?
@EliteHydronics.
4 жыл бұрын
Brilliant channel ! 👍🏻 thanks
@कोंकणकर
4 жыл бұрын
Sir please help me. How to select condenser inlet and outlet temp. And pressure for refregeration system. Which book refere to me?
@robertingersoll5289
4 жыл бұрын
The ASHRAE PH chart Enthalpy is different from Danfoss PH chart Enthalpy values. Do they use different datums?
@akashpathak5895
4 жыл бұрын
Will components be compatible if not purchased from Danfoss? Suppose if we use this software for components selection(compressor, evaporator, condensor, etc) will it be compatible with other companies products
@solankipratik8071
4 жыл бұрын
Can we design brine type block ice machine based on freon 404a?
@shreyaskumbhar7047
4 жыл бұрын
Very informative
@ahmedmahmoud4566
4 жыл бұрын
Dear sir Thank's Pleas l wante know How many meters The Evaporater and Condenser in the industrial chiller stc ice maker how can l calculati il? pleas
@talhaozden4041
3 жыл бұрын
a very good work, How can I find enthalpy values at different temperatures and pressures (for R410 fluid)? I need to have the T-S diagram drawn.
@EngineeringMindset
3 жыл бұрын
theengineeringmindset.com/refrigerant-properties/
@MihaiP12
5 жыл бұрын
How are the properties calculated at point 3 when considering a degree of subcooling, thus the point not being on the saturation line? I would like to know what tables or formulas to use to obtain enthalpy and entropy at that point located in the zone of subcooled liquid refrigerant. Thank you in advance.
@EngineeringMindset
5 жыл бұрын
Check our design videos
@estherkyere6937
Жыл бұрын
Thanks for the video
@udithaatukorala6578
6 жыл бұрын
dear sir ,your videos are v.good .i wont to design -35 c freezing bath for pop ice (popsicle ).please help me.thank you
@EngineeringMindset
6 жыл бұрын
Check out kzitem.info/news/bejne/tYaXyKpvonZ2gZg
@OthmanAlikhan
2 жыл бұрын
Thanks for the video =)
@kaf2303
Жыл бұрын
Excellent!
@kimgalinato3634
2 жыл бұрын
This also applicable at AC Design?
@EngineeringMindset
2 жыл бұрын
Yes
@JJ-mg3pr
4 жыл бұрын
We need training for cold room in Bangalore India.
@EngineeringMindset
4 жыл бұрын
Here you go kzitem.info/news/bejne/kZ2smKiAn2mfqqQ
Пікірлер: 30