looks great and saved a ton of money. I would powder coat but I bet you could get nice results with a spray can.
@TunerwithKids
3 жыл бұрын
I got lucky to find the fronts at my local You Pick. Else those go for $200+ from car-part junkyards. The rears are very abundant since the Touareg, Porsche Cayenne, and Audi Q7 all used the exact same calipers. As low as $20/ea at most junkyards.
@davidjteo
3 жыл бұрын
YEEEESSSSSS IM SO EXCITED!!! I went to LKQ Raliegh on Wednesday looking for Touraeg calipers and couldn't find any. But by the grace of GOD while I was walking back I looked up, and there was an untouched Cayenne! I found the wheel lock in the cabin, took off the wheels and BAM! It had 17Z's. SO thankful. Out there door all four for $113.25 :) We don't get much snow/corrosion here, and the car didn't have a lick of rust on it (garaged I assume) so I'm just gonna de-grease them and slap them on my Sportcross. I got Stoptech Sport slotted rotors up front and Stoptech drilled in the rear (the only option for IS-F unfortunately) on Blackfriday from Buybrakes.com and then OEM Brembo Low-Met pads from Rockauto.com. Can't wait.
@TunerwithKids
3 жыл бұрын
lucked out on the Porsche ones, also lucky you were carrying a triple square socket for the rear?. I just got done trimming the front to fit, it was a bear of a job and dust everywhere. Lots of work should have Vid up next week. Did you get the bracket from Overkill yet? The rears are tricky, you should have gotten RCF/GSF rear (they are same size as ISF but slotted).
@TunerwithKids
3 жыл бұрын
I just posted my front fitting video. Was a lot of work.
@thedon9830
3 жыл бұрын
Wow you took cleaning to the next level. Great work as always.
@thedon9830
3 жыл бұрын
Powder coat will last longer and gives it a oem finish.
@wombatau
2 жыл бұрын
Pagid pads are amazing, good score.
@LexusRepair
3 жыл бұрын
Nice upgrade for your is300 😍 Good job bro 👍🏽
@stuntdrvr
Жыл бұрын
I did my Porsche calipers in a single stage urethane acid green paint.. I totally stripped the calipers so no masking.. came out amazing
@TunerwithKids
Жыл бұрын
Check my newer videos from last month. Did a sick powder coating job on these.
@dyziplen.
3 жыл бұрын
Maximum Detail, always love your approach, can't wait to see these powdered up and how you mount them. Are you going to run a new master cylinder? I asked the track/racing group on FB about any larger BMC we can run on the 1IS but didn't get any solid answers..
@TunerwithKids
3 жыл бұрын
Naw, keeping the stock MC. This is for the bling anyway. The stock MC can handles these. The IS300 has some big stock brakes already for an 02. Dual front and dual rear pistons.
@L3XURIOUS
3 жыл бұрын
Powder coating for sure 👍
@rsforeign9493
3 жыл бұрын
what cars did you take them off i’m trying to order some but don’t know what make and module they came from
@TunerwithKids
3 жыл бұрын
The 17Z came mostly on early V8 VW Touareg and Porsche Cayenne. They were also found on the Audi Q7. It’s hard to guess if it was 18z or 17z but you can go my the rotor size spec. 18z uses the 360mm and 17z uses 330mm on the auto parts listing.
@boostedonabudget9018
3 жыл бұрын
link to the site where you got the calipers
@TunerwithKids
3 жыл бұрын
Check my junkyard videos. I got them at a LKQ Pull Your Part.
@CH121S
3 жыл бұрын
What do you put inside the ultrasonic cleaner? Is it just water?
@TunerwithKids
3 жыл бұрын
Warm water and some degreaser.
@jasonribeiro7312
Жыл бұрын
How did they perform on the car? Any change with brake pedal travel?
@jaysongarcia9383
3 жыл бұрын
I love it keep it up
@user-nu6yb7zn7o
Жыл бұрын
Хорошая работа 👍
@tahasultan7409
2 ай бұрын
Can i use the oem bolts on the rear to install the rear calipers to the car ??? Or do i need to buy the bolts you got .??
@TunerwithKids
2 ай бұрын
Probably need new bolts. If I could use the OEM I would have.
@ericludington6622
2 жыл бұрын
Where did you get the bracket and rca for the front calipers
@TunerwithKids
2 жыл бұрын
Check the links in description. The brackets are custom from a guy on IG. Not sure if he still making them.
@turbogears900
11 ай бұрын
Would it fit toyota aristo jzs161?
@TunerwithKids
11 ай бұрын
Check with overkill engineering. He has brackets for Supra/SC which is same as GS.
Пікірлер: 30