your lecture is easy to understand.. keep up the goodwork sir☺️
@ELTronic3
Жыл бұрын
Thank you very much your comment..If you want to make a video like this tell me and I will make it.please watch my other videos ..thanks.
@ElJosesote
Ай бұрын
what software do yo use to make the videos? Result is great!
@ELTronic3
Ай бұрын
I using animation software for my videos project. Thanks..
@sohailjanjua123
2 жыл бұрын
Hi, I like your lecture. Thanks
@ELTronic3
2 жыл бұрын
Thank you..watch my other videos😍😍
@noorrahman9410
Ай бұрын
Digital relay installation ka video upload karay.
@ELTronic3
Ай бұрын
Ok. Are you want to digital relay using this project.
@Athletics907
2 жыл бұрын
I am working on a 2021 Ford F350 w/ factory upfitter switches. We are trying to use upfitter 1 as the power source for an LED beacon and 4 LED lightheads. We are trying to wire in a latching relay to cut power (or ground) to the rear 2 lighthead by wiring in a momentary button. When upfitter switch 1 is powered and all the lights are functioning (beacon and 4 lightheads) we are trying to use the momentary button to kill the rear 2 lightheads, but allow the circuit to reset when turning the upfitter off and then back on allowing power (or ground) to the rear lightheads allowing them to function again. The end user is wanting to make sure the rear lightheads will come back on through the upfitter switch 1 when turning the switch to ON. The end user works from the rear of the truck onsite and the rear 2 LED lightheads are at eye level. He is hoping to use the momentary switch to kill those 2 rear lightheads when working from the rear, allowing the other LED's (beacon and front 2 LED lightheads) to continue working, but when he gets back in the cab and turns the beacon and lightheads off killing all power to those heads, but allows the circuit to reset when turning upfitter switch 1 back on. I am having a hard time wrapping my head around this. I am close to figuring it out, but just can't get it sorted. Can this be done?
@ELTronic3
2 жыл бұрын
Thank your comment..😊
@ELTronic3
2 жыл бұрын
Draw what you want as a diagram and send it to me. supun030@gmail.com
@ELTronic3
2 жыл бұрын
Briefly state what you want.
@AztecWarrior69_69
9 ай бұрын
Did you get it working?
@satishbhanang3064
Жыл бұрын
best information sir ji
@ELTronic3
Жыл бұрын
Thanks your comment..subscribe my channel.
@Samyydapekinese2715
10 ай бұрын
TYVM!
@ELTronic3
10 ай бұрын
Thanks...❤️
@prabhashibeautytips1960
3 жыл бұрын
Good job .😃😃😃😃
@ELTronic3
2 жыл бұрын
Thanks😊😊
@janakasri6799
3 жыл бұрын
Good job
@ELTronic3
2 жыл бұрын
Thanks..😉😉
@brightfame7984
2 жыл бұрын
Awesome setup! Can this wiring be applied on a motor for a 2 floor elevator replacing the stop switch with limit switches and the light with a 1/8 hp motor?
@ELTronic3
2 жыл бұрын
Thanks. The elevator uses a 3phase motor or a single phase motor.
@brightfame7984
2 жыл бұрын
@@ELTronic3 Single phase motor only.
@ELTronic3
2 жыл бұрын
A 1 / 8hp motor is not enough for an elevator, is it?
@brightfame7984
2 жыл бұрын
@@ELTronic3 Actually it’s only for a dumbwaiter for small items like a laundry basket.
@ELTronic3
2 жыл бұрын
This motor should run forward and reverse, right?
@mdshiponmia8265
Жыл бұрын
Thanks
@ELTronic3
Жыл бұрын
Ok friend..
@pasatiemposyartesanias
4 ай бұрын
Me podrias explicar por favor por wue la entrada número 3 energiza la bombilla, cuando la bobina se energiza solo 8 ,6,1 y 4 quedan cerrados
@pasatiemposyartesanias
4 ай бұрын
?
@ELTronic3
3 ай бұрын
Relay point throw on off output ..
@ELTronic3
3 ай бұрын
❤️❤️❤️❤️
@simeonpalenzuela9241
2 жыл бұрын
Is it possible to include Schematic Diagram in your video.?
@ELTronic3
2 жыл бұрын
kzitem.info/news/bejne/upVv1YmYkWNjaH4 The circuit must be set up according to this video.you can try now
@rizwanmustafa117
Жыл бұрын
How to make like that videos which software using any one can help plz
@ELTronic3
Жыл бұрын
Are you like my videos...
@amirularif466
Жыл бұрын
isn't the start button should be normally open?
@ELTronic3
Жыл бұрын
Yes friend.it is star button should be normally open.
@AztecWarrior69_69
9 ай бұрын
What software are you using to create the animation?
@ELTronic3
9 ай бұрын
Animation software..🙂
@AztecWarrior69_69
9 ай бұрын
@@ELTronic3 Yes What animation software, what is the name?
@brentbarnhart5827
2 жыл бұрын
I thought people finally learned about stupid music... I guess some didn't.
@ELTronic3
2 жыл бұрын
Thank you..😊
@janakalilani6598
3 жыл бұрын
This circuit use for water motor.
@ELTronic3
3 жыл бұрын
Yes, you can use this circuit..Motor should be less than 5Hp.
@ELTronic3
3 жыл бұрын
Thanks your comment ..😍
@ammarbasrah1362
Жыл бұрын
How is the connection
@ELTronic3
Жыл бұрын
14 pin relay have four relay out.(common pin and n/c and n/o pin ) other 2 pin is power pin A1 and A2..you can use one relay point (small current out)use two point parrellel out put( high current )
@ammarbasrah1362
Жыл бұрын
If use 14pin relay
@ELTronic3
Жыл бұрын
Yes you can use 14 pin relay
@ELTronic3
Жыл бұрын
14 pin relay have four relay out.(common pin and n/c and n/o pin ) other 2 pin is power pin A1 and A2
@shahziadahmad7595
2 жыл бұрын
This circuit is wrong .we gave to use negative in no point .
@ELTronic3
2 жыл бұрын
Negative (neutral line) go to output line directly.phase line switch relay point
@ELTronic3
2 жыл бұрын
Thanks your comment..😊
@shahziadahmad7595
2 жыл бұрын
Phase will be direct to light and neutral will be pass through reley common and then pass from open to lamp .am i right brother?
@ELTronic3
2 жыл бұрын
No friend you wrong..The neutral line first goes to relay A2 and then to the neutral terminal of the light bulb.
Пікірлер: 66