@@AKRChobby7274 If your existing remote is model RH1v2 then no need to replace it. If you don't have v2 then you need to replace.
@AKRChobby7274
Жыл бұрын
@@MickoRC thanks bro 👍🙂
@AKRChobby7274
Жыл бұрын
how to find out if it is v2 or not please bro reply me 🤔
@MickoRC
Жыл бұрын
@@AKRChobby7274 have a look here photos.app.goo.gl/pki4NdAJmpurD5kF6
@boomjeep99
Жыл бұрын
Like 7mph gain not bad try 3s now
@GAMINGJR1210PD
2 жыл бұрын
Does the controller need to be reprogram again?
@fearless3geclipse
Жыл бұрын
Was the transmitter easy to bind?
@cpbudgetrc4501
3 жыл бұрын
Hi my friend I know this is an old video but did you have any problem getting the pinion gear on the motor shaft
@MickoRC
3 жыл бұрын
Hi mate. No it just went on nicely. I could push it on by hand.
@hasanabas4554
3 жыл бұрын
How did you install the light the plug light bigger than the socket of receiver!?!!;!?!!?!!thanks
@MickoRC
3 жыл бұрын
I replaced the plug with a jst xh 2.54 2-pin plug. Cheers for watching
@slick1095
3 жыл бұрын
How did you Install the lights cause I am trying to get some lights to install but I don’t know how to do it
@MickoRC
3 жыл бұрын
There's existing holes in both bumpers for LEDs. I used a bit of superglue to secure each one in. I connected the LED wires to a 3-pin JST 1.25 plug and plugged it into the ESC. Because the LED set I used has 8 LEDs I used the remaining four on the body - just taped them down for now.
@slick1095
3 жыл бұрын
@@MickoRC thanks man
@whatchamahoozit
3 жыл бұрын
hi, just wondering, can you turn those LEDs off via the switch on remote?
@slick1095
3 жыл бұрын
@@whatchamahoozit I can’t right now but I ordered a connector to to put in the esc and if you have the right connector you should be able to turn it of and on
@MickoRC
3 жыл бұрын
@@whatchamahoozit @slick That's an excellent question. The manual says you can, but it doesn't work for me.. the LED switch on the transmitter does nothing. 😌 But another viewer who's 1621 is a couple of years old said his LED switch works, so maybe only the older models work. Just FYI.
@nathanieljaca5943
3 жыл бұрын
Nice Video,Happy New Year po
@alionthrottle
3 жыл бұрын
Hi Micko How did u bind the esc to the remote. I bought a 3 wire esc and brushless. Can you please advise
@MickoRC
3 жыл бұрын
Hi Ali, If you bought the Remo E9931 ESC which has a built-in radio receiver you should be able to easily bind the existing transmitter to it by just turning on the transmitter and then turn on the ESC.
@alionthrottle
3 жыл бұрын
@@MickoRC thank you for the response. That's what I did and it worked.
@alionthrottle
3 жыл бұрын
Hi Micko, Do you have any idea about calibrating the ESC and transmitter ? I installed brushless motor and ESC and bind it. It works great and is fast. However I have trouble braking. It barely breaks. Im looking for some help on getting the brakes back. I have Remo brushless ESC fyi. Any help would be appreciated.
@WHOISDENIS
3 жыл бұрын
Hi, my remo hobby 1621 has a xh2.54 of 5 pins and one of 2 pins connector and a jst one ¿Did you know for what is each one? I hope your help soon. (Sorry for my english, im spanish) Edit;(Happy New Year bro 💪)
@MickoRC
3 жыл бұрын
Hi bro. That sounds strange. I don't know. Are all these connectors coming from the ESC? Can u pls send me a pic of it in a private message via my FB page? facebook.com/MickoRC thanks!
@MickoRC
3 жыл бұрын
I got your FB message. The 2 wire port is for LED lights power
@predatoryt8503
3 жыл бұрын
May filipino ba jan may nadinig akong 'wala na ala na"
@MickoRC
3 жыл бұрын
haha opo mga pinoy kami. 👋🇦🇺🇵🇭
@predatoryt8503
3 жыл бұрын
@@MickoRC hhahahha kaya pala parang may nadinig akung nagsalita ng tagalog😂😂😂💯🇵🇭
@TheBestOrion
3 жыл бұрын
46kmh is plenty for offroad bashing 😁
@MickoRC
3 жыл бұрын
Yeah I'm rather happy with it 😀 Thanks very much! Happy new year to you bro!
@aleksandr..6560
3 жыл бұрын
Молодец!!!) Я не понимаю что именно нужно купить чтобы передать машину... У меня Smax 1631.
@MickoRC
3 жыл бұрын
Thanks for your kind words! 😊 Parts for the upgrade I performed are listed in the description. Thanks for watching!
@manueljr2974
2 жыл бұрын
Wat can I do to make mine go straight is so hard to keep it goin straight wat do I need a better servo ?
@pitseedohcovers
3 жыл бұрын
Astig na upgrade yan sir ang galing talaga..
@MickoRC
3 жыл бұрын
Thanks so much bro. Musta ka na bro? nasa camp pa kami hanggang bukas. cge bro happy new year to you and your family!
@blackpowderpig375
3 жыл бұрын
Cool Car
@pitseedohcovers
3 жыл бұрын
@@MickoRC ok lang sir will be back yt on January.. Happy New Year din sa inyo sir.
@gilbskie88lagalag98
3 жыл бұрын
Happy New Year 2021 po!
@MickoRC
3 жыл бұрын
happy new year bro!
@jorgenmagnusson6245
3 жыл бұрын
Great video. Just bougt this car to me and my son. Remohobby has 2 servers E9812 and E9822. Do you know the difference between the 2?
@MickoRC
3 жыл бұрын
Hello! I hadn't heard of the E9822 before. From my quick online research it appears Aliexpress are selling the E9822 but the brand is actually JXServo, model number Pdi-2504mg. Visible difference is that the output spline on this servo is metal and on the E9812 it is plastic. Though apparently both servos have metal gears inside. Both are 25 grams but I am not certain they have the same dimensions or speed. I hope this helps. Thanks very much for watching my video. Have a great day and stay safe!
@carmelagumpal2380
3 жыл бұрын
🥰🥰
@denwilliams79
3 жыл бұрын
How the heck did you manage to get the spur gear onto the metal drive shaft (A4028)? It seems like the plastic shaft is thinner where the spur gear goes on, but the metal one is the same thickness all the way. Banggood pics seem to match mine, couldn't see yours properly before installation to see if yours was different.
@MickoRC
3 жыл бұрын
I might have tapped it in with a hammer. Honestly I can't remember. I mustn't of had an issue with that. Just force it on? 🤔
@gilbskie88lagalag98
3 жыл бұрын
grabe ganda ng mga toys car mo Sir Mike astig sana lahat magkaroon niyan panglibangan lang pag walang ginagawa,galing astig!
@MickoRC
3 жыл бұрын
hehe sana all bro
@aleksandr..6560
3 жыл бұрын
У нас она стоит примерно 50 долларов - 3600 рублей. А сколько она стоит у Вас?
@MickoRC
3 жыл бұрын
Based on the prices now at Banggood, it costs around AU$85 in total for all the parts listed. Fortunately Banggood send these to me for free to do this video/review. 😇
@islandrc-duke1972
3 жыл бұрын
Cool upgrade"nice run
@MickoRC
3 жыл бұрын
Thanks very much brother! It certains rips alot more now. ☺👍
@jared4670
2 жыл бұрын
Do you really need to change to the Remo E9812 3Line 25g Servo when converting to brushless?
@MickoRC
2 жыл бұрын
Hi Jared. Yes, unfortunately, because the existing servo is 5-wire and the brushless ESC/receiver combo omly has a 3-wire socket for the servo.
@jared4670
2 жыл бұрын
@@MickoRC Thank you! Alright then, do I need to change the remote as well? I have seen packages where they include a new remote to go with the ESC/Receiver. I guess its not a huge issue to have another remote control though...
@MickoRC
2 жыл бұрын
@@jared4670 If the model of your existing remote transmitter is RH1-v2 then you can use this. This worked for me.
@yanahsimplengprobinsyana2371
3 жыл бұрын
Ang galing naman po...
@MickoRC
3 жыл бұрын
maraming salamat po!
@drefschannel2227
3 жыл бұрын
Nice .. Happy New Year! #mamo
@MickoRC
3 жыл бұрын
Thank you po. Happy new year din!
@davydlg
3 жыл бұрын
What kind of battery you have? I am looking for a battery for Remo 1635 :(
@MickoRC
3 жыл бұрын
I'm using a 2S LiPo. There's plenty out there. Just make sure the dimensions will fit into the battery bay on the car
@davydlg
3 жыл бұрын
@@MickoRC Where can I find that battery? You are using that model in Remo 1631? Cheers from México!
@MickoRC
3 жыл бұрын
@@davydlgTry Banggood or Aliexpress. I forgot to mention the particular battery I am using in this video is a 1000mAh LiPo battery from my Xinlehong Q902.
@davydlg
3 жыл бұрын
Thanks bro!✌️
@MickoRC
3 жыл бұрын
@@davydlg You're welcome brother!
@napster69er
3 жыл бұрын
Hi sir good day! Is the new esc compatible with the stock remote?
@MickoRC
3 жыл бұрын
Hello there.. It is only compatible with the transmitter model RH1v2 which is the stock transmitter I received with my 1631. Have a great day!
Пікірлер: 70