Very nice job, thorough and well thought out. It’s nice to see someone who really takes pride in their work and cares about the customer. 👍👍
@EliminatorPerformance
2 жыл бұрын
Thanks for watching!
@JamesNickersonThePhotoShopGuru
2 жыл бұрын
Thank you, I learned something … I learned that I need to come visit you and bring my snowblower to you for a “refreshing” …. Thank you for sharing this video 👍🏻👍🏻🙏🏻
@EliminatorPerformance
2 жыл бұрын
Thanks for watching!
@darinjohnston5750
2 жыл бұрын
Hey man! Gotta say love your videos..I tore apart my craftsman snowblower and your vids saved me..changed belts,oil,greesed everything,new shoes, new auger bearing only because it was seized on there and had to be torched off. No small engine mechanics around town anymore and the one that is your put on a waiting lists for months. Just a shout out yiyr helping tons of people out. Great job.God bless. D
@alanrobison3298
2 жыл бұрын
Another awesome video! We don't have much use for snow blowers down here in south Texas but at least I know how to replace that bearing!
@EliminatorPerformance
2 жыл бұрын
Thanks for watching!
@garny3766
2 жыл бұрын
Nice textbook demonstration. For the folks without a split puller, a 3” air cutoff tool and hammer and chisel will work too. Actually you can get them off faster than the time it takes to setup the puller. The bigger pain can be the pulley. For that I weld nuts or bolts onto the side of pulley sleeve and from there I can use a steering wheel puller or heavier gear puller. Once off, cut welded on nuts/bolts off. For replacement options on some of these snowblower bearings oem is the correct way, but if a guy is handy universal flanges and bearings can be found at many farm stores. New holes may have to be drilled but it can be done.
@EliminatorPerformance
2 жыл бұрын
Yea it's never fun having to cut them off, sometimes they get really bad, this one came off with a bit of heat and the puller. Thanks for watching!
@dginta7932
2 жыл бұрын
Gawd, I wish I was closer to you ... you are amazing. Thanks for the video, another great vid.
@dginta7932
2 жыл бұрын
Any chance you would know what puller matches up to the impeller pulley holes on the Yamaha YS928J snowblower? The service manual only refers to a puller for the stator, which is also a 3 hole puller. I didn’t think to measure the bolt hole pattern when I had it apart.
@Samlol23_drrich
2 жыл бұрын
That forkin' tool is awesome.
@EliminatorPerformance
2 жыл бұрын
So many uses lol thanks for watching!
@harryharry3193
2 жыл бұрын
good job...you customers are lucky to have you heat is your friend
@EliminatorPerformance
2 жыл бұрын
I always try my best. Thanks for watching!
@TheShadeTreeFixitMan
2 жыл бұрын
Great explanation of the whole process.
@EliminatorPerformance
2 жыл бұрын
Thanks for watching!
@gerardlunow567
Ай бұрын
Buy OTC. They cost more but their tools are as good as it can get and nave fail you. I have a drum puller, ball joint set, and the puller you show. I use them with a light electric impact on occation but most likely just hands. These tools and acetylene heat are a must.
@BrucesShop
2 жыл бұрын
Man you have all the toys. Thanks for the fun
@EliminatorPerformance
2 жыл бұрын
Really enjoying using this induction heat gun, but as mentioned, it's definitely not needed. The split puller really comes in handy though!
@chrisssmallengines7163
2 жыл бұрын
Great video , With the quality of parts slipping this will be a fix the you will see more often . If you do not have a puller or a induction heater , a very careful cut with a grinder will work or a propane torch maybe helpful .
@EliminatorPerformance
2 жыл бұрын
Yes we've had to cut them off before as well lol never fun, thanks for watching!
@repairitdontwreckit4257
2 жыл бұрын
Nice work. Quality work and information. Lots of excellent tips.
@kjell-richardlvdal373
2 жыл бұрын
Great video on possible problem on removing befaring, ball befaring is the best some blower use only bronce bushing not good
@EliminatorPerformance
2 жыл бұрын
Yea and I'm seeing more and more plastic now on these newer units. Thanks for watching!
@jamiesawyer5102
2 жыл бұрын
Great content as always.
@EliminatorPerformance
2 жыл бұрын
Thanks for watching!
@brandonharvey7939
2 жыл бұрын
When using the puller, use a 1/4" drill bit to create an indentation in the center of the bolt head so that the puller doesn't slide around and slip off
@rickbroerman9267
2 жыл бұрын
Great video once again Jake
@EliminatorPerformance
2 жыл бұрын
Thanks Rick!
@TheRustyRooster
2 жыл бұрын
👍that should straighten it out for a good while
@EliminatorPerformance
2 жыл бұрын
Yessir, thanks for watching Rusty!
@Big_Johns
2 жыл бұрын
Nice work Jake 👍🏼
@EliminatorPerformance
2 жыл бұрын
Thanks John!
@Big_Johns
2 жыл бұрын
Anytime brother.
@gordbaker896
2 жыл бұрын
With a thin blade on a grinder, grind down beside the shaft, cutting open the cup (inside) tube of the Bearing very close to the shaft. Likely Hammer or Air Chisel will then remove Shaft. Done. Do not over use the hammer or chisel or you may damage gears in gearbox.
@kenhilson786
2 жыл бұрын
I just use bolts for the 2 pieces that screw into the split halves.
@ExclusiveK9Alberta
Жыл бұрын
I have craftsman model 16.5T 31”, is this the same parts ?
@kenhilson786
2 жыл бұрын
I noticed your bearing has no keyway. I've worked on some Murray noma units that have keyway. On none keyed I've seen bearing seize in race so shaft turns in bearing and a groove wears in shaft. Last case I used jb weld to fill the groove.
@EliminatorPerformance
2 жыл бұрын
Yes, some seem to have them, others don't. Many of the new ones only have the keyway in the pulley now
@waynestefinashen239
2 жыл бұрын
Smooth video son, actually it seemed a lot shorter than what the actual time of the video was. The Mini-Ductor has been a very useful tool in the shop, especially on bolts with red Locktite. The OLD MAN wants to know when he is going to be able to do a video LOL!
@EliminatorPerformance
2 жыл бұрын
Yes it has definitely helped, such a good tool to have in the shop! And one of these days we'll get you on a video!
@donvoll2580
2 жыл бұрын
Yes we want to see the old man doing a video..lol I am guessing that the young man possibly learn some from the old man. Thanks
@waynestefinashen239
2 жыл бұрын
@@donvoll2580 Thanks Don but it is the other way around, the old guy learning from the young one and it has been a great experience. Gives me something constructive to do in my retirement.
@waynestefinashen239
2 жыл бұрын
Thanks Jake i think i hear a fan calling LOL! They were even talking about me on a video on Conkers live stream.
@dougbailey6999
9 ай бұрын
Where did you get the bearing.
@dginta7932
2 жыл бұрын
Another question, please. I ended up buying a new impeller shaft for my snowblower. (It was seized on and pretty pitted when I got them apart. Even after cleaning it up it was a bit loose with the impeller fitment). On the original shaft the shaft was painted between the bearing housing and the worm gear housing. I imagine this was to protect the exposed shaft from rust. Wondering if just coating the new one in ‘anti-seize’ (and keeping it coated throughout the snow season) in your opinion would be a reasonable way to go? I am thinking that if I paint it, then it will prevent me from pulling the new impeller off once in a while to re apply anti seize, to prevent it getting seized on, again. Thanks.
@EliminatorPerformance
2 жыл бұрын
Antiseize would work great, I use it on bare metal all the time. Apply it heavily as it's cheap insurance!
@dginta7932
2 жыл бұрын
Awesome, thanks.
@sullivanspapa1505
2 жыл бұрын
viewed and subscribed a few days ago to learn how to work on my 24” MTD snowblower. I ordered all of the supplies you used. You could have picked up some cash on my purchases IF you had a link to Amazon. I don’t know how you do this but I urge you to check this out!
@cliffbrown4217
2 жыл бұрын
I saw another guy on youtube advocate beating on the shaft with a hammer to seperate the bearing from the shaft, do you agree that beating on that shaft with a heavy hammer might damage the worm gear in the gear box
@dr.lmsb4456
2 жыл бұрын
Where did u get the mini heat conductor? Awesome video brother . Thanks for the tips .
@EliminatorPerformance
2 жыл бұрын
Induction Innovations! Check out these 2 videos; kzitem.info/news/bejne/uq2Xs66mj4CdiIo kzitem.info/news/bejne/2Wmqu6SfgaR1aH4
@dr.lmsb4456
2 жыл бұрын
@@EliminatorPerformance thanks brother i will
@kbssmallenginerepair2615
2 жыл бұрын
Sure seems like the venom hp sure gets used a lot around there. Maybe I would use it a lot if I had one! 🤔😬 Good video nonetheless!
@EliminatorPerformance
2 жыл бұрын
Yea I'm finding more and more uses everyday for it, like I've always said, can still use a torch, but this thing is just so simple to use. Thanks for watching!
Пікірлер: 56