Awesome information. I’ve been out of the shops for over fifteen years and am somewhat new to this platform. I’m currently replacing the engine in my wife’s 13 Avalanche and let me tell ya… NEVER EVER AGAIN. I now remember why I moved into service writing and then out of the industry all together.😂
@J.Crooner
2 жыл бұрын
If you're fortunate to get those bolts out then I'd replace them with some standard six point bolts.👍😎👌
@Mreasytoo
Жыл бұрын
These three bolts are kicking my ass... iv got one finally so two bolts. This engine swap has turned into a time consuming issue due to these Allen head bolts.!!
@MODOORTEK
Жыл бұрын
YES!!! this is the video i was searching for! Great help, Thank you Sir!
@Djmedic23
Жыл бұрын
Thanks for the video. Im pulling mine in my burban and got 2/3 out fine 3rd one stripped so trying this before before welding on it
@bambeeno1411
Ай бұрын
What size are they
@bobbyhancock170
Жыл бұрын
I just done mine in my 01 gmc 5.3 and used extensions at the front of the truck got all 3 out but not without busting my knuckles first ouch but im going to replace rhem with regular bolts thats for sure
@user-os6qt4hi9y
Жыл бұрын
Snapped my flex plate in my an was able to hand loosen those bolts 🤣
@jasminekolar400
2 жыл бұрын
Cool
@toneloccskii
15 күн бұрын
What is the other smaller inspection plug next to the big one? I know the big one shows the flywheel but what’s the purpose of the other?
@WilliamJones-pl2hx
2 жыл бұрын
What would you do if you had torque converter bolts go in at an angle?
@chriskolar
2 жыл бұрын
You mean they were cross threaded? Take it back apart Drill out the messed-up threads Tap to a larger size If that is not possible, then the anchors will have to be removed and new ones installed.
@radioactivecat1345
Жыл бұрын
Does that access hole need a cover on it?
@chriskolar
Жыл бұрын
Yes, there is a cover for the access hole
@adriangarcia7307
2 жыл бұрын
How long did you heat up each bolt?
@chriskolar
2 жыл бұрын
About 2 minutes, approximately 250 degrees to get the thread locker loosened up.
@adriangarcia7307
2 жыл бұрын
@@chriskolar gonna give it a shot today hopefully it all turns out alright. Thanks for the video
@adriangarcia7307
2 жыл бұрын
@@chriskolar i also doused the bolts with pb blaster so gonna try it later see how it all goes
@adriangarcia7307
2 жыл бұрын
Update: I tried the this method it did not work for me. So what I did I heated the bolt for about 4 minutes than put a breaker bar with a 8mm hex and luckily it worked and I didn’t round out the nut.
@bensonben921
7 ай бұрын
What’s wrong with a regular bolts. Why Allen wrench
@chriskolar
7 ай бұрын
I suppose the factory has a machine that tightens up the bolts.
@joshratcliff3065
11 ай бұрын
I'm working on my first ls 5.3 everyone loves these engines why ??? This has been the BIGGEST PILE OF SHIT I HAVER LAYED WRENCHES ON BESIDES A JAGUAR LONG TIME GM FAN BUT GAHH LEEE MAN ! The fucking cam bearings fall out when you pull the cam fucking really 😅!! I've never in the 100 cam swaps on gm ford's dodge seen somthing soo pathetic . The ones that didn't fall out look like some one went in there with a die grinder with a cartridge roll for porting all I can say is I sure hope this cam swap and head work ,tune an torque converter wakes this turd up !. My 1997 z71 could do donuts around this turd !!! Sorry I was just venting !!
Пікірлер: 23