*Good **MyBest.Tools** value compaired to other brands*
@insylogo
2 жыл бұрын
I was gonna say "just buy a replacement, would be way cheaper than this full rebuild and turning and all that," but then I googled how much a cordless rebar cutter costs. Holy cow good job!
@sypernova6969
2 жыл бұрын
this was REALLY impressive. the whole built, the fit and the finish on the aluminum piece.
@timteecvhn
2 жыл бұрын
Tbh I'm quite impressed with how well that lil cheap motor handled powering the hydraulic pump to get thru that big ol' piece of rebar at the end. Like that's just impressive that it managed to get thru that.
@megaman992
2 жыл бұрын
I’ve used a little hex impact drill like that in a pinch to take lugnuts off.. powering a little hydraulic pump should be easy, on top of being brushed to brushless upgrade
@GerstBladeworks
2 жыл бұрын
@@megaman992 agreed. The motor doesn't really do much work it's the hydraulic pump that holds the load.
@scroungasworkshop4663
2 жыл бұрын
Well done, it looks like it came that way. I think you made a good decision to not open the hydraulic pump as they can be a nightmare to reassemble and the fluid was clean. Cheers Stuart 🇦🇺
@rynecjohnston
2 жыл бұрын
What a Frankenstein-looking tool. Great restoration!
@ftownroe
2 жыл бұрын
Another fantastic restoration. The modification of the modern power source to fit the restored unit to include the machining of the transition section is next level craftsmanship.
@mattrezek320
2 жыл бұрын
The big sigh at 3:24 when it spills all over hit me in the feels
@anands6127
2 жыл бұрын
Making the connecting flange was really hard task that you did nicely. I think that lathe machine is our new member
@JoeRocket-sf6qs
2 жыл бұрын
Alot of time spent to fix a worn out tool,but I admire the effort/skill to make it nice to look at.
@sally6457
Жыл бұрын
I'm new to your channel, and I'm instantly hooked! The previous videos I've watched have been great, I've been inspired, with your help, step by step I've fixed a few of my old tools, I'm on top of the world, full of confidence, by watching you, I can do it too!! Until now, McGyver and the A Team have nothing on you!! Absolutely Brilliant 👏 👌
@stepcorngrumbleteats7683
2 жыл бұрын
Brilliant Restomod, Didn't stop, just kept finding ways to succeed... Most Excellent. Thank you for sharing.
@teddyenriquez3429
2 жыл бұрын
A very skilled restoration artist with knowlege in machine works, electricity and electronics.
@freedomofmotion
2 жыл бұрын
Amazing to watch and amazing skill. But couldn't help but feel making a mount for the smaller motor in the original housing would be so much more efficient 😂
@Maranello12374
Жыл бұрын
Очень хорошо..Я часто смотрю твои видео и сам люблю что то востановить,отремонтировать или переделать..Мне нравится смотреть как ты востанавливаешь инструмент. Привет из России
@Shawn_the_Protogen
2 жыл бұрын
That cutter seems very gentle cutting the rembar, it doesn't suddenly break it and make a loud noise.
@user-xr5py3zm1i
2 жыл бұрын
Проэк супер, но сделал такой красивый переходник, а насадку не почистил и не покрасил, было бы как новое всё!
@antoninpourroy9582
2 жыл бұрын
12:40 the dremel speaking Italian 😂😂
@azioprism3635
2 жыл бұрын
*we have cheap and efficient angle grinders these days but i didn't know such an add on existed, very interesting.*
@christianhilditch9333
2 жыл бұрын
When the budget jumps into hundreds of thousands the consumer tool market falls short of what the industrial trades have. Decking gun that drive finger sized "nails" into thick steel beams. Portable hydraulic benders for pipe or re-bar. Some job sites won't let you make a spark so no friction cutting tools. Hilti has made hi-torque battery powered impact guns and grinders for years before milwaukee even thought about it.
@ideaoverload910
Жыл бұрын
Near video should be restoring and making the front part look like it matches, like it was one whole tool. Awesome video.
@lolcec81
2 жыл бұрын
Комментарий в поддержку канала и ролика, а также труда мастера ремонтника.
@user-rr7vs8wx4u
2 жыл бұрын
Отличный ремонт
@mgnstore
2 жыл бұрын
Ещё 3d- -принтер добавить и можно самостоятельно инструмент делать, а не переделывать))) А так залипательно и прикольно)
@FaZuQ
2 жыл бұрын
Еще можно самому накопать в шахте медь, железо и выплавить
@hassankhosravi3306
2 жыл бұрын
آرامش شما توی کار رو خیلی دوست دارم. عالی بود ممنون 👍👍👍
@Jugc0006
2 жыл бұрын
I am Soo impressed. You should sell it. Pit it on an auction for your viewers.
@oneshotme
2 жыл бұрын
Great job fixing and making parts for it but why didn't you clean up the cutter part of it?? Enjoyed the video and I gave it a Thumbs Up
@DockterDoom
2 жыл бұрын
My god, I've never seen a pinion puller that small. Now I need one B)
@Abedjuc_85
2 жыл бұрын
In the beginning .. I thought that not get fitt . But that was creative . Amazing job 🥰
@user-me1us4ln5h
2 жыл бұрын
Что вы там сами не можете? Когда он вал переходной изготовил ,я уже был восхищён но вот когда из балванки такое выточил! Молодец
@wpowerwagon
2 жыл бұрын
Just wow, a really great job of repair, and thanks again for sharing your thoughts and great video
@yeahright3348
2 жыл бұрын
seeing you use the tap at the end made my arse pucker up. looked so close to snapping.
@akabiscuitwaffle
2 жыл бұрын
we need to fund our boy a milling machine, even if it's just a manual one.
@peteraugust5295
2 жыл бұрын
Why the impact wrench when the cutter is using a hydraulic reduction?
@LP-ei4pi
2 жыл бұрын
Однозначно молодец! Золотые руки! 🤝👍
@gosha.87
2 жыл бұрын
Мы сами себе создаём трудности и героически с ними боремся!!!
@powertoolsrepair
2 жыл бұрын
Great restoration and video
@sysierius
2 жыл бұрын
Finally! Nailclippers that are worthy of my nails!
@blackops84321
2 жыл бұрын
Awesome job. You have a great talent.
@en2oh
Жыл бұрын
fantastic! Thanks for sharing the approach you took to solving this problem.
@cukupalan4147
2 жыл бұрын
Kalau bisa di perjual belikan akan lebih ada manfaat nya dan berguna lagi dan harga di sesuai kan dengan harga pokok... Mungkin ini yang dinamakan ide jenius ada nilai tambah dari barang yang sudah jadi di tambah pemikiran yang baik 👍
@user-iv9rl4nv7f
2 жыл бұрын
Разобрать гайковёрт что бы собрать это сомнительная выгода)
@sergek2172
2 жыл бұрын
думаю, главная выгода -- контент и комментарии. Ну и сделал всё же рабочую вещь.
@AlexxxxBY
2 жыл бұрын
Так она и так рабочая была, нужно было просто акб подключить.
@tomswindler64
2 жыл бұрын
Good video,impressive retro fit.you mean the old one wasn’t a makita keep on doing what your doing.👍👍👍😎😎😎
@shanefowkes7451
2 жыл бұрын
Is it just me or those sounds while sanding the aluminium @ 12:51 these sounded like the ray gun Toy I had when I was a kid wow the early 90s where a blast for me, other than that fantastic video, from a metal worker point of view - very little planning from what I could see but over all I'm very impressed
@hgghgguk
2 жыл бұрын
Seems like a lot of effort to repair something that you could probably just buy new for the same cost you repaired it for but yeah, ik you were doing it so you can improve your own skills and make a good video and it turned out well, good job :)
@franksando635
2 жыл бұрын
Also knowing it could be done is better yet beside would would not been able to watch it
@Capturing-Memories
2 жыл бұрын
You should have covered the magnetic core with tape, It is hard to clean the metal shavings. Also for machining the contour of the aluminum piece, you could have mounted the drill with the cutting rotating bit against the lathe and turn the lathe head by hand for the three 120 degree portions to machine that lip.
@Evergreen1400
2 жыл бұрын
I was very surprised he didn’t use the lathe to contour that piece. He still did a good job but I figured the lathe would have been the machine for the job rather than a dremel
@AJ1990.
2 жыл бұрын
12:48 - Sounds like when Schwartz in A Christmas Story is pleading with Ralphie not to leave him because his tongue is stuck to the pole.
@oherman
2 жыл бұрын
When a not-so-genuine Makita was repurposed to do something extraordinary.
@doctorlefthandthread
2 жыл бұрын
Wow that is phenomenal you are an artist
@jareklotz
2 жыл бұрын
What a great project. Congrats. Btw. Could you repair my wife?
@alanerickson3075
2 жыл бұрын
Nice work makes me wish I had a lathe.
@kylemarcelo24
2 жыл бұрын
watching from Philippines 🇵🇭
@oleque1
2 жыл бұрын
Lots of skilled work. Nice!
@daves4026
2 жыл бұрын
Beautiful work
@Mad.Man.Marine
2 жыл бұрын
Awesome!! Absolutely awesome work!!!
@Beggli1996
2 жыл бұрын
Well done dude. Fantastic.
@cujbaion1
2 жыл бұрын
They should make newer with fast gap closure, for thin bars would improve the response time
@scottpecora371
5 ай бұрын
I confess I had my doubts but that turned out damn impressive! BTW: i assume you did but change the gear oil. Preferably with synthetic. I'm certain it oil requirements will be in the owners manual on line! Also stir a magnet through the oil to see if its shedding metal.
@pirateskeleton7828
2 жыл бұрын
The problem with brushed motors is that when they get stuck, they take on the new title of short circuit.
@user-qh2ml4hp1c
2 жыл бұрын
А нужно было только батарею добавить и всё
@AlexxxxBY
2 жыл бұрын
Вот и я про это написал, там всё и так рабочее было. Работа ради работы сделана и загублен новый гайковёрт, ну как говорится всё ради бесполезного контента.
@christianvolpato7579
2 жыл бұрын
Cool restoration and very impressive tool!
@user-gv4tn9nb7f
2 жыл бұрын
Thank you; was very pleasant to watch.
@sddiymakeitworthit7512
2 жыл бұрын
Really great job 👏
@thomasgaucher-peressini8785
2 жыл бұрын
thats a 1000 $ tool good job
@DaSlotho
2 жыл бұрын
7:36 where has that tool been all my life?
@yeagerxp
2 жыл бұрын
Awesome 👍👍👍Thanks for sharing.
@MICUTU511
2 жыл бұрын
You made me say: wait what a couple of times. Makita wannabe was the hardest one. (The original Makita is not cheap at all).
@maxhouseman3129
2 жыл бұрын
There are some mounts for a hand mill to mount it on your lathe. Just an idea for saving time.
@mobinurrahman6783
2 жыл бұрын
Nice work man..
@robertdiehl4384
2 жыл бұрын
What benchtop power supply is that? May be looking for a nicer one for my tinkering
@donparker8246
2 жыл бұрын
Very nice job. Works like a charm.
@solehhadi7714
2 жыл бұрын
12.19 = mini EDM 😁 nice 👍
@REAPER85151
2 жыл бұрын
u could out faze the bolts to use the old screw holes ,,,, and making a milling machine from an angle grinder maybe next project...
@matthewhall435
2 жыл бұрын
Loved this project very well done !
@takis8vas
2 жыл бұрын
Use a centering bit on lathe! it will make your life a lot easier ! good job tho. i was curious about that small motor having enough torque to cut that!
@Pascal_Robert--Rc_Creations
2 жыл бұрын
Dont forget to add oil to drill bits and taps, especially in alluminium. Otherwise they gum up and dont work as well.
@Ironclad17
2 жыл бұрын
Be honest, you make pew pew sounds whenever you use it.
@sebastiannielsen
2 жыл бұрын
I wonder, why didn't you simply take longer screws and screw all the way from black flange to the blue plastic? Seems the hole pattern is similiar enouch that it would be possible.
@eternalanubis4205
2 жыл бұрын
So how do I watch a video like this with a simple fact that these no talking like please explain to us what in the world you're doing damn tool like please makes it so much more interesting that way
@myrestorations
2 жыл бұрын
Congratulations for the video, friend 👏 👏👏!!!
@vitorcarleto283
2 жыл бұрын
Does the sound of 'loss of power' when you cut something big is it from the drill or the hydraulic system?
@Kregorius
2 жыл бұрын
I would guess it's the drill or specially the battery. Not the original brand, but the idea is the same. 3Ah Makita battery isn't the same as 6Ah battery. Size is one thing, but it doesn't drop the voltage that much under load. Most Makita battery tools characteristics are given with 6ah battery. Smaller batteries may not achieve it. Not that bigger battery would make too much difference but it would have more oomph to go.
@sockpuppets7256
2 жыл бұрын
the cutting bar probbaly isnt that sharp considering the condition of the tool
@hasankorzebor
2 жыл бұрын
this is professional work .... i like it man
@aldrinalejo1810
2 жыл бұрын
I wonder if you restore all the parts ..and paint it with silver..BTW nice idea
@___rkb___9598
2 жыл бұрын
use one for my toenails they work great!
@nordicvision1893
2 жыл бұрын
Wow. Thank you.
@presidentjoethudbrandon7074
2 жыл бұрын
I'd live to see that cheap plastic shell.replaced with a metal one.
@Thadeya.
2 жыл бұрын
If he just had put oil in the old machine. It was perfectly fine. 🤣
@charlievalentino6075
2 жыл бұрын
Los mejores 20 mins de mi vida 💛 que buen vidio
@sheepy777
2 жыл бұрын
Wait a min did homeboy put vegetable oil in the machine?
@user-oe7tw9iv4k
2 жыл бұрын
Cool and very useful tool!
@vi683a
2 жыл бұрын
This is a Mafia Tool!
@FerSniper
2 жыл бұрын
Спасибо!!!
@Ricky32908
2 жыл бұрын
My guy, you can save yourself 2-3 hrs or lathing, drilling, and sanding by getting a Cheap CNC $4,000-$6,000 you can find a decent one
@eduardopascualgarcia3660
2 жыл бұрын
Amazing job
@MixedGears
2 жыл бұрын
Nice rebuild, but I guess it would be way over budget to be financially viable :D
@nizammiah6511
2 жыл бұрын
Actually, a decent automatic rebar cutter will set you back several hundred dollars, and that cheapo impact wrench alone is about $40. So apart from labour costs, this is one of the very few restoration videos that seems quite reasonable
@merlinmagnus873
2 жыл бұрын
Very nice.
@Jimmitime
2 жыл бұрын
Simply wonderful
@michaeldavid4227
2 жыл бұрын
congratulations friend great job 👏🏻👏🏻👏🏻👏🏻👏🏻👏🏻👏🏻👏🏻👏🏻👏🏻👏🏻🇧🇷
@captainamazing1356
9 ай бұрын
Wow!!! So cool!!!
@garethjones6342
2 жыл бұрын
PLEASE FOR THE LOVE OF ALL THINGS CHEESY AND MOLTEN AND TASTY!! What was the hacksaw-ish saw-thing you used at 12:20 that was multidirectional and able to cut slack like that?? I MUST KNOW! Ps love you, stay safe!
Пікірлер: 198