Here is one method of debugging your Flight controller and saving some of your FPV money. Components used in this Video: www.digikey.co... www.digikey.co...
You deserve more subscribers, I searched all over the internet and found nothing for my omnibus f4 pro v3 controller, you know what? when I touch test prob on Vin of the voltage regulator it booted, which is kinda strange considering how it can turn on by just touching the single multimeter lead on Vin, then it slowly fades and processor gets hot so I removed USB cable quicker. After searching for hours I stumbled upon your video and the way you traced the issue is remarkable. Thank you so much for the video Sir, subscribed to you and seriously, such stuff isn't shown by the experts. if it's possible to shed some light on my issue would be very helpful. Guys sub to this lovely person. He deserves more subscribers.
@e2ekielus
4 жыл бұрын
Was the other probe on gnd when you touched Vin and it booted?
@xpertcrush
4 жыл бұрын
@@e2ekielus nowhere. Just one prob while multimeter set to voltage reading. Now it's very faint leds of I try again. So I quickly disconnect as mcu herts up. 3.3 and ground is shorted and I found couple of capacitor showing short.
@xpertcrush
4 жыл бұрын
Board was working fine. Yesterday I plug in battery and only heard escs beep. Does boards fail like this?
@e2ekielus
4 жыл бұрын
@@xpertcrush i wouldnt use test probes with usb powered up. pins are so close on these boards that you could short more components by cross contact. however considering the situation that it is receiving usb power when this happens it sounds like heat from the short has made the Vin pin desolder enough to have a bad connection and when you are making contact with the probe it is making better contact and trying to boot. but the short still exsist and is caausing the mcu to fault.
@osvaldolopez4549
2 жыл бұрын
I wish I would have seen your video a year ago. I have a couple of fc’s I can do the same you showed. Thank you 🙏
@andriy1000
9 ай бұрын
Amazing repair, bro
@aowbrasilfpv4797
2 жыл бұрын
Video entry with a Brazilian song, cool that., I'm Brazilian
@crushyad2939
2 жыл бұрын
how to fix flight controller when it shows short across diode? Thank Will!
@jasonburbidge3964
4 жыл бұрын
HI HOW DID YOU KNOW WHAT 0402 CAPACITOR TO USE?
@dustinplee5067
Жыл бұрын
My flight controller says config file appears to be corrupted ASCII what does that mean and how do I fix it I was trying to flash it in betaflight
@h2o-fpv623
3 жыл бұрын
men thank u for this video its giving me an idea on how to fix a flight controller that is new but i guess i damage and i subscribe thank u again.
@marcosmatos8213
2 жыл бұрын
When testing regulator output voltage should I use a ground pad on the board or the battery negative pad? I have a betafpv 12a aio that I get correct voltage reading on both the main linear regulator that feeds the ESCs and the 5v regulator when placing my negative lead of my probe on the battery negative. But if I place the negative lead on a ground pad I get 1.4 volts on the 5v output and input with the F411 already out. haven't found a dead cap yet, I just started fixing this stuff about 2 months ago and have been able to revive a ton of gear and is so satisfying but I always go back to this board determined to figure it out someday.
@e2ekielus
2 жыл бұрын
Marcus, if you can, send me a short video to my email showing me these results. I think I may be reading something wrong in your question.
@f0xvibes
2 жыл бұрын
How do you found out the right value for the dead capacitor?
@Ammar50767
4 жыл бұрын
Can you help Me with my flight controller it has solid red light on it. I was installing firmware update something went wrong
@dmhans22
4 жыл бұрын
What is the cause of 3.3v issue? Short?
@srul76
4 жыл бұрын
Is the pin out from the regulator is common for most of the 5pin regulator or I should look for the datasheet for each difrent one?
@e2ekielus
4 жыл бұрын
Some pinouts are slightly different on regulators that might look similar however for this FC the pin outs are all the same.
@Waylandir
5 жыл бұрын
I don't have the skill or the equipment to do that type of micro-soldering. What would you charge me to fix 2 Kiss V2 FC's?
@e2ekielus
5 жыл бұрын
Waylandir well that would just depend on the parts needed for those specific fc’s. Would need to be debugged first. Btw I didn’t have my hot air solder gun at the time I filmed this video. I actually used a temp controlled solder iron with a really small tip. Works just as good just not as easy.
@srul76
4 жыл бұрын
BTW excellent video 👍👍👍
@Toast_Charms-lm6mr
4 жыл бұрын
Hey I’m in the video 🤗🤗🙃
@CarbonGlassMan
3 жыл бұрын
Thanks for making this video. It is really going to be a big help in trying to track down my problem. Where are you getting the electrical components? I can't find the 3.3v regulator A1117B 3.3 HJ. I ordered an AMB1117 regulator thinking it might work, but it's too large. I trimmed the legs down and made it work anyway, but the pads under the regulator are all shorted. Well 3 of the 4 pads are grounded, so where can I buy the tiny caps? Thanks.
@e2ekielus
3 жыл бұрын
Digi-key has a large selection. Shipping is fast too
@CarbonGlassMan
3 жыл бұрын
@@e2ekielus Thanks. I also found a place in China called LCSC Electronics. The STM32F405RGT6 is $5.38 each.
@shaundsouza
2 жыл бұрын
@@CarbonGlassMan which was your flight controller?
@CarbonGlassMan
2 жыл бұрын
@@shaundsouza It was a Mamba F405 20x20. It was a MK2. My 3.3v regulator was getting very hot as soon as I put power to the flight controller but the problem was not the 3.3v regulator. It was the F405 chip that was shorted out. I bought a few F405 chips and replaced the one on my flight controller and the flight controller works fine again. I'm still flying it today.
@shaundsouza
2 жыл бұрын
@@CarbonGlassMan I have the same flight controller, the 5v and 9v led's are on but not the 3.3v power rail led, I hope it's just the 3.3v regulator that's burnt out.
@jmc_fpv
10 ай бұрын
Hi, did you substitute the processor or it was only the caps and voltage regulator??
@e2ekielus
10 ай бұрын
Jmc, in my case it was only the cap and reg.
@jmc_fpv
10 ай бұрын
@e2ekielus but did you still have a short after remove the last cap?
@e2ekielus
10 ай бұрын
No. the reg shorted which caused the cap to short. Any trace after the cap was not damaged. Your case might be different
Пікірлер: 36