Solo un video reparando los auriculares de mi trabajo. Tienen un pésimo diseño fácil de romper. Just a video fixing my work headset. This model have a really bad design and is really easy to break.
Thanks man. Worked like a charm. Used 2,4mm rivet. Drilled with 1,5-2-2,5 mm metal drills to keep it nice and centered. Holds nice and don't expect it to break.
@Tignuss
2 ай бұрын
Thanks for the details about the rivet size ! To be more specific you will need 2.4 x 10mm that you will cut around ~8mm long. 6mm are too shorts. Also, for those with the microphone side broken, it is more delicate. Look up other videos on how to open it (force/pry on the ear at the right place), drill the same hole but be careful as it will touch the PCB. Then you have to trim like 3/4 of the head of the rivet (instead of the small cut OP did in this video) so it can fit and once you push it in, it will lock behind the PCB and you can't remove it without removing the whole PCB. I did scratch my PCB while drilling and some copper was visible but for now it works fine.
@ekummel
4 ай бұрын
That's a really good idea using a rivet ferrule as a reinforcement of the pivot point. I just wish you showed more of the disassembly part. I'm having a difficult time getting the collar off so I can get to the remainder of the broken off plastic pivot part. And getting that ear piece off with all that plastic, I'm afraid that I'm going to break something!
@erikbust7209
2 жыл бұрын
thanks man ! really I was about to give up and buy new ones
@jhonattanespilcodelacruz5972
10 ай бұрын
Muy bueno el video, en mi caso se rompió el que tiene el micrófono pero no se cómo desarmarlo para soldar los cables
@oienu
10 ай бұрын
De hecho, se me rompió de los dos lados. Básicamente es igual, el único problema es que ese lado viene soldado por calor, o sea, en lugar de tornillos sujetando el PCB, tenía unos postes de plástico que derriten por lo que este queda sin forma de removerlo, para poder repararlo simplemente corté todo el tubo, no tiene el tope del remache del otro lado, solo un corte en diagonal para darle espacio al cable y lo demás lo sujeta la resina. No se ha despegado.
@mariagallo89
Жыл бұрын
Muy bueno el video! el problema es que a mi paso con el otro que tiene el conecto y la ficha de prendido
@oienu
Жыл бұрын
El problema es que no tiene tornillos en la placa de circuito, sino que va insertado y soldado (básicamente derritiendo los postes de plástico) podrías retirarlo y volverlo a pegar o simplemente dejar el cuerpo del remache, realmente en mi caso se rompieron los dos lados, pero del otro no se ha desprendido tampoco pese a que solo coloqué el tubo sin el tope del extremo para no tener que sacar la placa.
@user-vg3sq9pb2w
2 жыл бұрын
Thanks man, but one question. How did you remove the trim where you screwed the fixing bolts on 11 minutes of this video?
@oienu
2 жыл бұрын
I had to cut the plastic on that parts because is just by pressure and I was more afraid about break all. Anyway that part is not structural so I just use black electrical tape to get all together again. kzitem.info/news/bejne/mGmqzIuYrKt9p4o
@ConstAnnTeenGreenChuck
2 жыл бұрын
@@oienu I just opened it without cutting. Thanks to your videos I understand how it built inside. You can slide it off. It is hard, but possible and it saves the trim.
@oienu
2 жыл бұрын
@@ConstAnnTeenGreenChuck I was like 20 minutes XD and was more possible to me break all so the safe way was cut it, anyway I had epoxy to put all together if need it
@Saddamkhanvlogs-bs8cw
Жыл бұрын
Bhai a shop kahan per hai mujhe bhi theek karvana hai apna
@nienow4
Жыл бұрын
Good work
@micrologypl9360
Жыл бұрын
it looks like it is hidden problem for Jabra65, my first headset was replaced under warranty, but those new after almost 2 years again has been damaged in the same place, in the same joint but they refused, because Jabra for replaced products giving only 6months of Warranty ....
@oienu
Жыл бұрын
Is a design flaw, that piece work fine but by aging the plastic become more weak and that point is too small, the new model look more sturdy. My first attempt was using cyanoacrylate but the shear force is too big, so I put that metal reinforcement using epoxy.
@BraianBe
4 ай бұрын
Alguien que me los arregle así en Colombia Bogotá, cuanto cobrarían?
@Fred-R
Жыл бұрын
Gracias por este tutorial, tendré que hacer lo mismo... ¿Cual es el diametro del remache por favor?
@oienu
Жыл бұрын
no sabría decir directamente, solo compré la más pequeña que tenían, si lo mido con el vernier son como 3/32", como dice otro comentario usó uno de 2,4mm (probablemente igual porque son 2,38mm) y realmente la broca que usé también era la de 2,5mm que compré en Steren (una tienda a de electrónica, se usa para perforar circuitos impresos). El avellanado es con la broca de 3mm solo para eliminar un poco del filo interno y evitar dañar el cable, en teoría no debería rozarlo, pero es mejor prevenirlo igualmente.
@Fred-R
Жыл бұрын
@@oienu muchas gracias 👍🏼
@Saddamkhanvlogs-bs8cw
Жыл бұрын
Mera bhi jabra ka headphone hai kharab ho gaya please mujhe bataiye kahan per shauk hai mujhe theek karvana tut gaya
@victorsalvo5896
2 жыл бұрын
oh man, i broke the same and i dont know how open it, pls do you can make a video open it
@victorsalvo5896
2 жыл бұрын
oh, i see the another video jajaja
@oienu
2 жыл бұрын
@@victorsalvo5896 I was recording using my Lumia but because the overheat I never can do all on one take, so somes parts are loss.
Пікірлер: 24