Just followed this video and managed to replace a damaged FEP film within 20 minutes. Very easy to follow, and definitely works a treat. Many thanks Anycubic.
@clintstlaurent4263
3 жыл бұрын
"According to the tightness of the FEP" - Which would be what exactly? Instead of the meaningless music how about letting us HEAR the tone when you thump the installed FEP? Maybe provide a proper tone value so we can use an audio app to tune it?
@yeeturmcbeetur8197
3 жыл бұрын
I still giggle even from the original photon FEP replacement video that I watched a year-ish ago when I bought my original photon that a bottle cap is still a necessary part to get this to work. Never change anycubic, never change 😂 Ordered my mono X yesterday. It’ll come in on Monday (4 days). Can’t wait!!!!
@KonkelVonk
2 жыл бұрын
I want to buy a Mono x, are you happy with yours? My other choice is Elegoo Saturn
@yeeturmcbeetur8197
2 жыл бұрын
@@KonkelVonk very happy. Extremely sturdy and absolutely no z wobble. Super high quality prints as well.
@bbigboy01
10 ай бұрын
A good tool to have for a hole maker in the FEP sheet is a door hinge hole centering tool. It fits great into the tapered bore of the ring and centers a nice clean hole into the center of the screw bore. It works fine, but if you want to even improve on that, make a fixture that lifts the total ring about 5mm above the surface your working on. This will allow the centering tool's center pin to full penetrate the FEP and make a nice round hole for the screw's placement.
@brokenheroics8223
2 жыл бұрын
Super useful. Just changed my fep now and this helped.
@shivercanada
3 жыл бұрын
Thank you! I love my Mono X it's amazing!
@christopherjoiner2798
3 жыл бұрын
The mono x fep size is advertised as 240mm x 165mm and the Elegoo Saturn 297mm x 210 so you can use the Saturn fep and trim to fit. Since both printers are pretty new I'm not surprised stock of replacement sheets are low.
@jimmyjames1807
Жыл бұрын
fep doesn't come particular sizes for each printer, they come in a generic size, like small medium large, its like anything u buy, tshirts come in s m l xxl xxxl xxxxl , same thing
@MarcoNoPolo
2 жыл бұрын
Before installing the frame into the vat, run a pair of scissors around the edge to trim off the excess film. It's much easier than cutting it off after it's installed.
@barrysmyth7496
Жыл бұрын
Great tip, I used a model knife & it was easier than scissors :)
@MarcoNoPolo
Жыл бұрын
@@barrysmyth7496 I bet you can get it done really quick that way. I think I'll use that method from now on. =)
@jimmyjames1807
Жыл бұрын
@@MarcoNoPolo dont not a knife, use that plastic scraper u get with printer, thats why the supply u with 1, make sure u use the metal scrapper on the fep when have a fail
@neohsiewpeng8078
2 жыл бұрын
Thank you for the helpful video. Bottle cap works great, perfect FEP tension. 👍🏻👏🏻 Keep up the good work!
@frumpeting
3 жыл бұрын
Good video. Where can i order the bottle cap?
@yeeturmcbeetur8197
3 жыл бұрын
God, if they sell 13mm tall anycubic bottle caps on their store I would shit 😂
@vladimirharkonnen458
2 жыл бұрын
I’ve got one I can ship to you for $4.99.
@rolandmine6693
2 жыл бұрын
@@vladimirharkonnen458 4.99 LMAO
@StreamerLimelight
2 жыл бұрын
No way this guys serious right?
@professorcannabis8748
Жыл бұрын
mine are 10.99 comes with water
@ShatterBox
3 жыл бұрын
Thanks for the video, where do I get a replacement fep sheet for the mono x?
@robertmckelvey3091
3 жыл бұрын
What upgrade do I need to take screws out that quick and how much was it the upgrade
@Lutzow706
2 жыл бұрын
Thank you for posting this!
@jankais3r
3 жыл бұрын
Please start selling replacement vats and FEP sheets for Mono X. It is ridiculous that there are no official replacement parts.
@tomkazansky9911
3 жыл бұрын
Video on how to change the Pep film of a photon mono? The whole is made from plastic and it too easy to crack it when changing film
@SilasoftheLamb
2 жыл бұрын
Awesome vid! Thank you!
@JPLGFun
3 жыл бұрын
How thick is the FEP?
@manuel_57334
Жыл бұрын
How tight should the FEP srewed together, or isnt there a limit (except to the point where its already worn out while installing)? Many thanks forward
@Mad_Catter_
Жыл бұрын
FEP Torque rating? FEP Frequency? Torque of the screws? Distance for Anycubic Photon M3 Max? Cap still the same?
@raymondjayjohnson693
3 жыл бұрын
Where can we get NFEP, instead of FEP, for this printer? Is EPAX the only source, and will their films fit?
@fleamarketkeanu
2 жыл бұрын
Love you, Anycubic!
@FarhadKazombie
3 жыл бұрын
Still no link to the actual product. Pathetic customer support from Anycubic. No replacement part available anywhere???
@J-_-S
Жыл бұрын
and where did you put smaller screws?
@PJthePlayer
3 жыл бұрын
Where can we get these replacement FEP films?
@ray24051
3 жыл бұрын
www.mcmaster.com/fep-film/
@3dprintingjean-pierrefabri854
Жыл бұрын
G Great tip, the cap to give amplitude to the film.
@mustafaassad2916
3 жыл бұрын
Where the one can buy a replacement FEP? Its an essential part need to be available once the printer released.
@robertmckelvey3091
3 жыл бұрын
Amazon has them
@jimmyjames1807
Жыл бұрын
google it , does ur internet not work
@mikaelbjornson2666
9 ай бұрын
Did you just install the FEP with the protective film still on? Otherwise, why is it so cloudy in the final shots?
@Alvar_g
3 жыл бұрын
is the same system for the Phonton mono?
@ryolacap
2 жыл бұрын
Ordering a mono x, how often does this occur?
@PierresVLOG
3 жыл бұрын
instead of the ridiculous annoying music you could've let us hear how the fep should sound when tapping after tightening it. It has a very distinct sound to it that could help some ppl get the tension correct.
@codubob4787
Жыл бұрын
따라하니 쉽게 되네요. 도움되었습니다
@lacrauzorro
2 жыл бұрын
A noob question: When do you know it's time to change it?
@shotgun2010
Жыл бұрын
How do i know if the FEP is too tight
@Redbox013
Жыл бұрын
Done this procedure a couple of times. Worked but I still have a doubt about the last phase: tightening the metal frame on the vat. In this phase it is up to you to choose the tension of the fep... I don't screw all the way down but I stop at a certain point... there is a way to tension the film in a more repeatable way? In the video this is not underlined. They just screw some bolts but how hard?
@Mad_Catter_
Жыл бұрын
I'd recommend a torque screwdriver, but as for how tight, I have no clue. Some people recommend tuning the FEP sheet with a PC speaker playing the right frequency, but again, I have no clue what frequency for each model of printer.
@stargana7585
2 жыл бұрын
Anyone else come back to this video just for the song?
@ideasdecoleccionista2979
3 жыл бұрын
Donde puedo comprar el fep de la mono x???
@workrase1
Жыл бұрын
Please make a video on the m3 max replacement. Is it the same? Again thing with the bottle cap?
@Mad_Catter_
Жыл бұрын
I wish to know this too.
@HBComics
Жыл бұрын
what size for X2 model?
@starshipengine
3 жыл бұрын
Just watched this to check after doing.. all else the same, I didn’t use a bottle cap. Do I need to redo it? Do I need to re-zero the z axis? It feels like there is a few microns of gap between the fep and the glass
@rewalczak74
2 жыл бұрын
i have never used a bottle cap and things are fine.
@remmside
3 жыл бұрын
y donde compro el FEP film?
@gomzovoncel
3 жыл бұрын
Where can I buy that film in Germany? Anycubic store shows no FEP film for the Photon Mono X!!!!
@gomzovoncel
3 жыл бұрын
@mw w 👍thy
@MikesProjectsandHobbiesMC
3 жыл бұрын
Amazon has it.
@eujin209
3 жыл бұрын
Thanks for this video. Should I need to replace my Mono X FEP down the road, I can refer back to this.
@jimmyjames1807
Жыл бұрын
its a 1 time only, they change the method daily, once you see it they change it
@erieschl
2 жыл бұрын
@3:47 is there a specific tightness for the fep or do they just mean to not over tighten the screws?
@rolandkohler1155
2 жыл бұрын
i have the same question. I would appreciate an answer, Anycubic. Thank You!
@williamvalentin7647
2 жыл бұрын
Same question here!
@Diamerlin696
3 жыл бұрын
Good video but where can I get the fep film for the mono x?
@mrfumetsu
3 жыл бұрын
Considering my FEP came pre-damaged for me, and not having the same answer... I ordered the .1 and .2 from here: www.amazon.com/gp/product/B07GRLC4H4 Should be able to cut this to size.
@anycubicsupport917
3 жыл бұрын
Hello, Thank you for reaching out and sorry for the trouble it may cause. Our tech support team will reach to you soon. Could you please click the link below, so that our tech team will know the details and give a hand. support.anycubic.com/en Please feel free to contact us if we can be of further assistance. Thank you! Regard
@Chippers_
3 жыл бұрын
@@mrfumetsu Which thickness worked best for you?
@user-sk2ec1il5s
4 ай бұрын
Ok for mono x2 ? Thx
@tribelaboratory9845
2 жыл бұрын
can you play the drums on it?
@shaggyrumplenutz1610
Жыл бұрын
The techno-Disney music slaps.
@poussinmoumoute
Жыл бұрын
Je ne comprends pas sur mon film moi jai un coté givré et un coté lisse lequel va en haut?
@jimmyjames1807
Жыл бұрын
can you explain the reason for the bottle top? the the thinking behind it
@Mad_Catter_
Жыл бұрын
The FEP film is supposed to allow a certain about of movement so that when the build plate pulls up, the model that is stuck to the FEP (This is completely normal) gets pulled up. the FEP creates a parabolic shape if there is enough movement allowed, instead of a flat surface as friction differences between the two ways of doing it are drastically decreased in the parabolic method.
@andrewroberts7948
2 жыл бұрын
Just found this video after replacing my FEP following the instructions on the anycubic FEP replacement. Just a heads up, the instructions there say nothing about removing the protective film. I wish I had found this video before...
@jimmyjames1807
Жыл бұрын
i thought that would have been obvious, do u eat bananas with the skin on them, did u remove the protective screen off the build plate and the printers screen when u set up ur printer
@sethhanson5771
3 жыл бұрын
Where do you buy the replacement FEP for mono X
@dogbreath99
3 жыл бұрын
wondering that myself
@Flashjunky
3 жыл бұрын
I found some on Amazon - search for 280x200 and that's big enough to fit
@ray24051
3 жыл бұрын
www.mcmaster.com/fep-film/
@hanscakestealer8546
Жыл бұрын
This FEB tray makes since wish the Anycubic Photon had this instead of one set of screw brackets making it so you have to cram the damn thing into the tray
@atissanguansat5207
Жыл бұрын
I replaced my FEP but didn't use the bottle cap while installing. Now, the prints stick to the FEP and pulled down the whole magnetic plate. Could it be that the tension of the FEP is too much because of not using the bottle cap during the installation?
@poussinmoumoute
Жыл бұрын
Me too and there is one froted side on my fep wich one touch the resin?
@andreabadalassi
3 жыл бұрын
Make the fuxxing mono fep kit available!!!!
@sureshgobi599
2 жыл бұрын
How to buy this
@nostrodamus1980
3 жыл бұрын
careful when cleaning the frames, the metal is as sharp as a razor
@kinneyhomemovies5203
3 жыл бұрын
Nice reference. But why is the new film so scratched up?..LOL
@muh1h1
3 жыл бұрын
Probably because that makes it easier to see in the video ^^
@RiderRed
3 жыл бұрын
You all really need to provide all the data on your website if your are going to be selling these printers. Everything can't be out of stock all the time, all these people asking for Fep Film and specifics and getting no response is not professional, however you have no issue taking the money on time. I just got my printer less than 48 hrs ago now I want to do nothing but return it because I can get no supplies for it.
@chrisohms4244
2 жыл бұрын
i do not know what i am doing wrong :) i was able to print 2 stunning prints on day one with my printer but haven't been able to get it to print anything else in months : /
@noway8233
2 жыл бұрын
Clean the fep, relevel the bed, try again, maybe yuo need to sand the base
@edamnaf9265
3 жыл бұрын
You charge 35.99 for the sheets but *50* dollars for shipping? Are you nuts? I'm not getting ripped off in that manner.
@ray24051
3 жыл бұрын
5ft by 24 inch sheet of FEP for $32.35, you can even buy 10 foot sheets at www.mcmaster.com/fep-film/
@ShaunYouth
3 жыл бұрын
No gloves for cleaning resin? Bad form...
@botones3763
Жыл бұрын
POR QUE NO TIENEN ANILLOS DE ALUMINIO PARA EL FEP DE LA PHOTOMONO M3 ES UN ABUSO
@btomas225
3 жыл бұрын
Will this process work without the annoying music?
@JB-xg7io
2 жыл бұрын
Great video. You just have to mute the audio before watching :|
@MatMo.
3 жыл бұрын
Should have gloves if you are cleaning resin residue...
@casperdegooijer1556
2 жыл бұрын
I removed all the screw, threw away the old FEP film and then continued this tutorial just to notice that I dont have a single usefull bottlecap in my house. So in order for me to be able to print something again I have to buy a bottle of coke... Might aswell add 1 to the package or let the person know
@vdsmade
Жыл бұрын
👷👍
@rusiktehnik5048
2 жыл бұрын
God
@gsgidney
2 жыл бұрын
You skip from removing the bottle cap, to already having a tight fit... Come on man!
@JayStein777
3 жыл бұрын
Sand the edges of the metal clamp, and skip the bottle cap.
@jhorn64
3 жыл бұрын
What, why?
@jimmyjames1807
Жыл бұрын
@@jhorn64 cause do need the bottle cap, idiots will use a cap, the fep self tightens, well most printers they do
@hobbychanel5798
3 жыл бұрын
Good
@m8harry
2 жыл бұрын
Remove the music, its annoying and hearing the person tapping on the FEP would have been better!
@ItsBrody
10 ай бұрын
Kinda silly to make this video on a while background.
@MuteMyst
2 жыл бұрын
As annoying as the music is, any cubic so far has been by far the best company in my experience for 3d printing (I came from fighting with an ENDER 5 Filament as well as creality support). At this point any cubic is my Main go to for printers, but I may branch out later.
Пікірлер: 117