Anytime you don’t have to use a torch inside an attic is always a good thing. 👍🙏
@kg4muc
5 ай бұрын
Great job! Makes things a lot quicker using the RLS press fittings. Probably when you factor in the cost of oxygen,acetylene and Silphos brazing rods it probably equals out or might even be more cost effective. I see why that txv was clamped down so tight😊 You certainly did a nice neat job on this one ☝️ Thanks for the videos!
@AaronPowellvox
5 ай бұрын
Gotta love bolt on txvs!
@robalexander7348
5 ай бұрын
Nice job Curtis 👍 Au
@HVACGUY
5 ай бұрын
Thanks
@TomLawson05
5 ай бұрын
Great job as always curtis good troubleshooting and repair thanks for the video
@whatdoyouthinktodd
5 ай бұрын
You didn't cut the tube You man handle it when you were uncoiling it from the line. And yes you have two seals in that bag. Great job as always 😎
@HVACGUY
5 ай бұрын
Thanks
@stevencossaboon3237
5 ай бұрын
Nice work Curtis.
@HVACGUY
5 ай бұрын
Thanks!
@Eddy63
5 ай бұрын
Nice job Curt ... Thx
@billyk5107
5 ай бұрын
I want to get that pro press next it make a nice looking job
@jthonn
5 ай бұрын
No torches, though I like your brazing, the crimping does look easier. Nice job
@HVACGUY
5 ай бұрын
Thanks 👍
@lancelawrence3259
5 ай бұрын
Nice work
@jeremyfinch8320
5 ай бұрын
I appreciate your videos. I am a service technician from Atlanta.
@HVACGUY
5 ай бұрын
Thanks for watching!
@timnew8830
5 ай бұрын
Sir. Please buy your self the BAHCO adjustable wrench thin jaws no slip and you do not have to keep resetting the jaws
@brettrobinson3499
5 ай бұрын
Dang the couplings
@bigscout1584
5 ай бұрын
I usually take an 1/8 bit an drill through the cap that you took off and that way nothing can fall in the pipe and block it being as all the insulation up there
@woodystokes1543
5 ай бұрын
Is this the second TXV for that one 😊 nice work 😊
@HVACGUY
5 ай бұрын
Yes it is!
@rudolfnavarette2987
5 ай бұрын
How do you determine if you need a powerhead or the whole valve?
@HVACGUY
5 ай бұрын
I only replace the power head if I can see the line is broken, and its replaceable
@bbaaspencer1
3 ай бұрын
Lowest dryer vent outlet I ever seen!
@jevinbrown7402
5 ай бұрын
What model Milwaukee is that? Would like to get the same set up.
@OnusBones
5 ай бұрын
Nice fix. How long do your batteries last (2.0AH M12) between charges?
@bobboscarato1313
5 ай бұрын
I hope kit comes with a spare battery which should be fully charged!
@OnusBones
5 ай бұрын
@@bobboscarato1313 I believe he has a column of batteries on their chargers in his van.
@bobboscarato1313
5 ай бұрын
@@OnusBones Thank you; he has lots of gadgets and back up tools and parts!
@HVACGUY
5 ай бұрын
Battery may last me 10 days of work or more
@andyvitz
5 ай бұрын
When you're feeling it with freon I don't know if you noticed but that machine was set for r10a
@andyvitz
5 ай бұрын
R410
@fernandobazan829
5 ай бұрын
hey curtis what happen to the high end appion vacuum gauge ? I see ur using FP again? I’m guessing it not clogging up with the new valve core tools?
@markchapman4197
5 ай бұрын
I'd adjust the txv a little
@billj4859
5 ай бұрын
Unrelated . Is anyone else having issues with the fieldpiece app since the last update?
@harrydickson4575
5 ай бұрын
👍👍👍
@shoosh9996
5 ай бұрын
Could that drier vent be closer to the condenser - lol
@maryfowler9997
2 ай бұрын
Don't you think that's a lot better than soldering. Sorry I used to burn up half the stuff around it if we had to limit what we soldered and where would this type of device you don't have those limitations do you agree with the new technology😊
@jimdavis6833
4 ай бұрын
I'm old school, and you lose me with the micron thing. I'm used to PSI and inches of mercury for vacuum. I suppose I could Google it.
@matt6962
4 ай бұрын
I like your videos but you are a man of too few words. I think your audience must be made up of more non-professionals so more words about what you are doing and what the tools and parts are would be very helpful to go along with your ample video. It took me quite a few videos to figure out that the special shader valve tool allowed you to change the valve and not lose the charge. I appreciate your videos!
@harryschrysan3183
5 ай бұрын
If this is a scroll compressor it's not advisable to pull a pump down especially when it's going less than 30psi. Copeland advices against it because it could arc. I am at the beginning of the video as I am making this comment.
Пікірлер: 42