When you studied to become a gynecologist, but changed subjects and become a motor technician
@Fatphobic.
11 ай бұрын
Underrated comment
@CAROLDDISCOVER-1983
10 ай бұрын
Cadillac telling a guy to turn his head and cough 😷
@scothubbard5323
10 ай бұрын
Fu keyboard warrior
@ericeric9475
10 ай бұрын
Когда учился на гинеколога, а работаешь проктологом.
@scothubbard5323
10 ай бұрын
@@ericeric9475 meee nooo speeeekie nooo russian! You're replying to Americans . Speak English or don't reply to my comments!
@robobrien6967
11 ай бұрын
You did all the work already to take the cv axle out though 🤔 all you qould have to do is pull it out and undo a snap ring (in most cases) it would probably be quicker even 🤔🤔🤣🤣
@Metradime
11 ай бұрын
Factual
@uenragedbro
11 ай бұрын
No, the outer boot only comes out after the inner boot comes out. This saves tons of time, axle seals and circlips, if you replace them. But he didn't pack it with grease
@robobrien6967
11 ай бұрын
@@uenragedbro so two snap rings my bad and no one ever replaces the axle seals unless they were previously leaking it literally would take about the same amount of time as this literally as this car sit he could just pop the axle out and break the clamps holding the inner and outer boot on pop the ring out split the axle shaft pop the second ring off and remove the outer boot and reassemble with grease the rings literally pop out easy as hell it's not hard and usually when yo by a cv axle rebuild kit you get everything to do this including grease but the time it takes to rebuild a cv axle is like nothing however you still need you get the knuckle out of the way that's where all your times at so this tool is useless and a waste of money
@robobrien6967
11 ай бұрын
@@uenragedbro and most of the time if you pop the axle out you don't need to remove the whole knuckle but to fit this big ass gun in there you do...so you actually spent more time getting things out of your way then you normally would
@uenragedbro
11 ай бұрын
@@robobrien6967 I guess the tool isn't for everyone. I think it saves time, and since time is money, it saves money too.
@dip5633
11 ай бұрын
And that's a lesson on how not to do it.
@tarcizoritter7151
11 ай бұрын
Crassulaceae.. lixo..crash..continue...me no..eu não!!! This is trash....stop please....
@SL-pg4dh
11 ай бұрын
It's good for a diy guy, but I don't want my mechanic I'm paying $650 to do this.
@adrianloska4247
11 ай бұрын
Suks... what about brand new grease?
@fastinradfordable
10 ай бұрын
@@SL-pg4dhthe fu k no Not good for diy😂😂😂
@CAROLDDISCOVER-1983
10 ай бұрын
In my comment I describe how I would use a split Boot and never have a problem with it back in the nineties. The big thing is you did not have to take anything apart. If you're going to take apart this far well rebuild the shaft with new CV joints or just replace it. Of course you better check and probably should only pull one shaft at a time and be sure to put the plug in so not to screw up the alignment or lose fluid. It all depends on the car. Like the old Mitsubishi in the Dodge 600 and what have you. You did one side at a time.
@CAROLDDISCOVER-1983
10 ай бұрын
Back in the eighties and specialty through the nineties they used to sell a split boot. You did not have to take anything apart. And the secret was to Put ATV clear silicone to 25-year version. Put it along that scene and then screw it together with the little screws that came with it. Then I would use Gates water and heater hose clamps plus a ATV at both ends and let us set a couple of days. Remember back then Gates clamps were fantastic! But I never had one of them to leak. How to do it for other people without any guarantees and usually on the weekends or when I had two days off in a row. Have them come back for the car 4 days after I was finished. I think I only charge anywhere from 35 to 50.00 plus the $7 for the boot. It was good spending money. If I was going to take this apart this far I would probably just pull the axle put the plug in. Replace the whole axle or at least the CV joints and not just the boots 👢. But I love this tool that this guy has
@KurtKoster-s6t
7 ай бұрын
Wish i had that tool back in the eighty's when front wheel drive cars came out,but the replacement boots weren't that flexible
@elttabykcir
11 ай бұрын
Seems like it would be easier, but it really looks like a lot more work!😢
@modifiedmechanix
11 ай бұрын
It's saves a little bit of time but when you do several day it really adds up plus you don't loose any differential fluid this way
@gilbertosoto9753
6 ай бұрын
That took no more than 10 minutes. I love it.
@daveytn
11 ай бұрын
Not sure when taking the cv joint off become difficult
@Chevytech1977
11 ай бұрын
It's definitely easier than this looks. This looks like it's a big pain in the ass! Also this way only works with the rubber CV boots. The plastic ones will tear apart
@modifiedmechanix
11 ай бұрын
@Chevytech1977 the nylon absolutely wouldn't work. These are actually sold by blue point for about $30
@hellsingdiablo23
8 ай бұрын
Ich benutze das an meinem PKW auch. Antriebswelle ist sehr schwer zugänglich in der Ausbau schwer. Die Kanone hilft da wirklich gut. Auch keine Probleme nach Wochen. 60 000km nach dem Wechsel immer noch gut 👍🏻
@jacobythomas8556
11 ай бұрын
When your wife says she wants to do a gender reveal and she hears the airline hook up lol
@jacobbrozenick8366
2 ай бұрын
So that’s what a customer price inflation device looks like, no wonder it hurts so much.
@paulkircher9542
7 ай бұрын
Great concept but in reality a few grains of sand rust grit in the grease and the cv joint is toast in a couple of months anyway.
@terrynieman4711
10 ай бұрын
So you teplace a boot but what about the dirt and lack.of grease in the rest of thr cv.? If boot was split in first place ..isnt cv shot ?
@exwldr6945
11 ай бұрын
Absolutely Rediculous That you even need something Like This What a Waste of Money!!
@modifiedmechanix
11 ай бұрын
Until you're averaging 20-50 a week. The mechanic that gets paid by the job comes out ahead and the customer vehicle down time is reduced dramatically by not waiting on parts and saves hundreds of dollars compared to some of the new axles
@rosengrantchris
11 ай бұрын
I'll take "How I pinched off my finger" for 200, Alex
@modifiedmechanix
11 ай бұрын
🤣
@GhaithAlshaary
5 ай бұрын
That’s how babys come out
@charlesjenkins1191
11 ай бұрын
I want to condemn and congratulate you at the same time. I hate those boots but i don't have that tool.
@seyavushabdulxaliqov
10 ай бұрын
)))😅
@fastinradfordable
10 ай бұрын
Meanwhile the other side just pops out with a screw driver 😂
@modifiedmechanix
10 ай бұрын
Buy you still would disassemble it to replace boot
@ha-dieg_b_e_8227
7 ай бұрын
Oft passen, wie auch hier, zu locker, die Achsmanschetten nicht 100% zu den Halterillen des Gelenks und sind bald wieder KO. Beim Zerlegen kann man auch besser das Fett erneuern. Wir verwenden den Spreizer kaum mehr 😢 keine 100% Arbeit, bei Garantie1- 2 Jahre zu beachten😮
@youngwang5959
4 ай бұрын
You need special cv boot that made for this tool. It doesn’t apply to every case. Factory boot will NOT expend that much.
@hagerhog118
10 ай бұрын
Genius tool. But for the cost of new axle....... you can have that tool
@stevedaniels3064
10 ай бұрын
That looks like more work than just replacing the half shaft.
@modifiedmechanix
10 ай бұрын
Yes when has repairing something be faster than replacing?
@tomas3861
11 ай бұрын
Same thing when i help my wife to put her long black latex gloves on
@MECHANICAUTOMOTIFSHORTVIDEO
9 ай бұрын
Best tools my brather
@ericetheridge9802
10 ай бұрын
Wish I had one of those years ago
@adrianloska4247
11 ай бұрын
Suks... what about brand new grease?
@modifiedmechanix
11 ай бұрын
It's a 60 second video
@Pamir19-61
10 ай бұрын
А кто промоет шрус после того как там стоял порваный пыльник?
@mikiejr111
10 ай бұрын
My boot tore and all over the web it said to replace the whole thing,once the boot tears the gears get dirt and water,no for de good,,,,cutting CORNERS WILL always come back to get you at the worst possible time
@modifiedmechanix
10 ай бұрын
I have done 100s
@mikiejr111
10 ай бұрын
@@modifiedmechanix All Good,being I have never done one I guess reading that the gears get spent put the fear in me,keep up the good work.I just went on 20yrs WITH my 03' Z71,I'm big on MAINTENANCE,disabled and dont DO anything I think will get me stuck in my garage.I have a 66'IMPALA SS ZZ502/600HP..5SPD,3:42 WITHOUT Boots,lol,Peace
@brianwright4058
11 ай бұрын
F that. He's a mobile tech. Put a new axle in the POS.
@modifiedmechanix
11 ай бұрын
Mobility tech?
@theblockchainclub1
9 ай бұрын
Now you got two broken rubbers 😂
@larrybrooks9068
11 ай бұрын
a speedy booth will work too!🤔😟🤣🥴
@pawegruba7787
11 ай бұрын
Super
@2strokelover93
11 ай бұрын
Bro the core charge for the old one is worth the quality and time you spent wasted. 😢
@modifiedmechanix
11 ай бұрын
Why would you need to have core charge repair the part. And it with out a doubt saves time
@ydgin1609
11 ай бұрын
Шрус снять было бы проще, тоже мне мастер😂
@Алекс-ы1о6т
10 ай бұрын
Проверка пыльника на прочность....😂😂😂 А сколько уже отбраковали?😂😂😂
@richardshoat8711
10 ай бұрын
Boot all stretched out now. Look at it😢
@ЕгорЛысенко-б8ь
10 ай бұрын
Мудрак😂😂😂! Шрус скинуть 2 мин! За одно и смаску сменить!!!! Это будет добросовестнее и качественее Я так по видео понял СТО не блещет качеством своей работы!
@kirbycollins3223
11 ай бұрын
That Tool Cost More that a Dozen Complete Axles 😂
@modifiedmechanix
11 ай бұрын
Nope
@natersalad889
11 ай бұрын
Lol this is comical actually
@robertpaul3675
10 ай бұрын
That thing is gonna leak like a siv cutting corners dont pay this is why i work on my own cars.
@modifiedmechanix
10 ай бұрын
Only done a few 1000 over the years with no leaks
@robertpaul3675
10 ай бұрын
Well can't say I've tested that out myself just looks to be a far stretch if it works it works
@modifiedmechanix
10 ай бұрын
@robertpaul3675 you have to use the rubber boots made foe it and not the nylon ones
@robertpaul3675
10 ай бұрын
@@modifiedmechanix that's cool, no disrespect on original comment just that thing looked crazy excessive of a stretch for the boots I've dealt with lol
@VadimGavrilenko592
10 ай бұрын
За такой «ремонт» надо отрывать руки в прямом смысле слова
@Toolaholic7
6 ай бұрын
Replace the axle,new axles are not that much money
@Vitali_L
5 ай бұрын
Бедный пыльник😢
@HawarHawar-z4u
7 ай бұрын
Why don’t you just replace the cv axle so you don’t have to do all that..the cv axle is prolly bad anyways
@cliffordbrooks1702
11 ай бұрын
Unless that’s a new CV joint and you replacing the boot on it you’re just wasting your time because you can’t rebuild a CV joint once they go bad you have to replace the entire joint and if you see one, that’s got a busted boot replaced the entire joint because they cannot be rebuilt
@modifiedmechanix
11 ай бұрын
What do you think they do with the ones with a core charge ?
@СветланаЛобанова-я6я
11 ай бұрын
Такие пыльники в наши морозы не ходят -30
@geoffreycalligan9438
11 ай бұрын
That's a REALLY bad idea. You have wear& dirt/ road grime in the hyphoid gear this is why EVERY tech manual is going to say remove,clean,inspect,then re-install boot& grease.Then re-install axle
@modifiedmechanix
11 ай бұрын
This would be more for one with a fresh cut or pin hole that hasn't been exposed to the elements. Have done 1000s over the years and not one issue
@geoffreycalligan9438
11 ай бұрын
@@modifiedmechanix ok But stretching the boot like that ,can't be good doing it the easy way & doing it the right way. Aren't always the same thing. I've replaced 100's of constant velocity shafts over the years. It's far more efficient. To just R&R the damn thing. And considering hourly labor costs these days. Likely a better deal for your customer. And an hours less labor for you. a CV shaft $60 to $80 from your supplier. As opposed to $125 an hr for labor. I'd say your a crook. And give the profession a bad name
@modifiedmechanix
11 ай бұрын
@@geoffreycalligan9438 the boots are designed for that. I wouldn't try that with an oem boot
@RowdyEnt.
11 ай бұрын
I can do it without taking the axle nut or rotor off. And without that fancy spreader. Figure that one out 😮 And leave a comment 👇
@JoeMama-j7s
11 ай бұрын
Rookie moves
@cobrajeff96
10 ай бұрын
There's no way that thing don't leak (again).
@БорисИванов-х4ш
10 ай бұрын
Слабо снять полуось, снять гранаты, промыть и впихнуть смазку?!
@RachidLhboob
10 ай бұрын
❤bou travail
@КарслиевПавел
11 ай бұрын
Быстрей было бы снять шруз 😂😂😂
@LAW-fv6ys
10 ай бұрын
Just a tap to remove it and then you can clean the joint properly and regrease and refit. I don't get why these are used and to save what 5 minutes and do a sub standard job in the end. 😂
@modifiedmechanix
10 ай бұрын
It still gets cleaned an greased. It's only a 60 sec video
@vugamer3594
11 ай бұрын
lol the tool for lazy people, and it will shorten the life of the boots
@modifiedmechanix
11 ай бұрын
The boots are made for it
@karamalqussiri6533
11 ай бұрын
How else is it supposed to be done?
@modifiedmechanix
11 ай бұрын
@karamalqussiri6533 with out the flex boots you have to disassemble the alxe
@Эрхан-м9я
11 ай бұрын
Ужасная работа!!! Мастер иди посуду мой в кафе или дворником работай!!!
@hellcatredeye-g6582
11 ай бұрын
Personally, as a mechanic, it’s just easier to replace the axle. Definitely interesting how they put it on though 😏👍
@ChrisPBolsak
2 ай бұрын
The use case for this is if rebooting is ~$80 but the axle itself is $800, especially if you want to stay OEM instead of going aftermarket
@allengreer8751
Ай бұрын
Really, what have you been working on, tricycle
@johnnyvdpijll2927
13 күн бұрын
Is it advisable to install an used axle? Or pay the full amount for new?
@name-less7268
11 ай бұрын
Two weeks later its clicking around corners. For the corner you cut by not replacing the half shaft. Boot 40 dollars axle 80 let's do the boot!😂
@modifiedmechanix
11 ай бұрын
Lost are getting over 400$ with long wait times
@name-less7268
11 ай бұрын
@@modifiedmechanix I have a shop. Most axles are nearly shot by the time they get a "boot service". They have usually been ripped for at least enough time for the grease to fling out and dirt to contaminate them. What's that tool cost 400 bucks. What do you charge to put the boot on? From what the video looks like you have to take off the same amount or more to get the room for the tool. One more step and the old worn out axle is popped out and the new one can be installed. I dont see the value in this. Constant velocity shaft should be replaced 90 percent of the time! Replacing the boot is a hack job. I have also seen ripped boots caused by metal from the CV coming apart from the inside.
@modifiedmechanix
11 ай бұрын
@name-less7268 these would be normally be used on one's that were noticed in routine maintenance or just happened to caught before any click or damage could be felt. We get alot of mud and hunting rigs in and it's normally a puncture from brush or rocks wouldn't suggest it to a shop that doesn't less than 5 or 6 a week buts its makes its money back after you do a couple
@andries4561
11 ай бұрын
Axle shafts are usually more than 200 in my area
@ipleedafif8033
10 ай бұрын
@@modifiedmechanixwhat warranty do you give for this type of repair? What was the labor cost?
@Tony-rl2fr
11 ай бұрын
... and THAT is how I met your mother.
@calsmith7902
11 ай бұрын
Excellent sense of humor 👏 ... I have no idea what you mean but my imagination is running with it 😅
@deant876
11 ай бұрын
Back in the early 90's when I became an auto mechanic, they sold speedy repair boot. The problem with putting a new boot on an axle that has split open, is all of the moisture and dirt that got into the axle while it was open. You have gone this far into reairing the boot, just spend the extra $100-$150 and replace the axle. Or you will be replacing it anyway in a year when the dirt wears out the joint
@roybriggs1951
10 ай бұрын
Damn straight
@deven6518
3 ай бұрын
So if your axle you got not too long ago, or is in good condition, needs a boot, throw it away? Uh, no. Change the boot. There is something called brake cleaner. As for the gluing, many cv boots are glued. There's cyanoasghu cv n g in glue (super glue) and well agents (rubber vulcanizing glue). With no gaps, it'll last years.
@taylorhubanks-os7og
11 ай бұрын
bros got the COD zombie gun
@modifiedmechanix
11 ай бұрын
For real 🤣
@manueljimenez4490
11 ай бұрын
Es un trabajo mal hecho gringuito.... Quitas la espiga, la lavas, metes grasa nueva y cambias la macheta sin broncas...
@cuckstianityisforcowards-rb9xi
10 ай бұрын
Yes. I always add new grease after changing out my machete. 😮 😂😂😂😂😂😂😂😂
@angel2304481989
11 ай бұрын
Might as well replace the complete assembly . Better and faster.
@modifiedmechanix
11 ай бұрын
It just depends on part cost part availability and if the boot was just starting to crack or had been cracked a while
@HawarHawar-z4u
7 ай бұрын
Thank you that’s what i said..it looks damaged anyways
@tbling
9 күн бұрын
Aftermarket axles have a bad rep. They are cheap
@robertlafrieda203
10 ай бұрын
I see some of the comments the guys don’t like this tool but when you have a dime store car roll into your shop that’s not worth $.35 and they’re down to their last hundred dollar bill a quick 60 bucks to repair a problem easy money for a Band-Aid fix if it takes the average mechanic longer than an hour they don’t know what the hell they’re doing
@BradcruiseUSA
Ай бұрын
a dollars a dollar i feel u bro
@calsmith7902
11 ай бұрын
That tool would take up a whole drawer in your tool box... Jiminy 😢
@modifiedmechanix
11 ай бұрын
Sits on top 😆
@jayo552
11 ай бұрын
HANG IT ON THE WALL,,.DOES EVERY TOOL FIT IN IT??
@juandefernandez3619
10 ай бұрын
Con una botella y agua caliente lo hacemos mejor 😅
@vitoprashad5670
11 ай бұрын
All these master mechanics in the comments that never had to deal with an axle that just refuses to come out Also if you catch the leaking axle early you wont have to replace it with a $80 axle that vibrates and starts to click after 2 years Well done, I would suggest both boots so you can pull it off the female inner end if you dont have the tool
@modifiedmechanix
11 ай бұрын
Exactly 💯
@SL-pg4dh
11 ай бұрын
And the $80 axle are Chinese made crap that will break in a few months. You are better off keeping your factory made axle and just replacing the boot if you joints are still good
@Anne_40
10 ай бұрын
You will not find replacing just the boot advised by the majority of people
@jonathankhan187
9 ай бұрын
No such thing as a “axle that refuses to come out” you got defeated by a simple axle
@SafdarAsghar-u3e
9 ай бұрын
Well done gd job where this tool available??
@LeonidasRAZDWATRZY
11 ай бұрын
Szybciej bym to zrobił zdejmując przegub ;)
@modifiedmechanix
11 ай бұрын
I'll race ya... 🏁 🤣
@billtmarchi4320
11 ай бұрын
Hey the proctolagist called, says he needs his tool back by Monday morning. He's got 5 exams scheduled and one surgery.
@EllsAutoCare
11 ай бұрын
Quality work man 👏🏻 saves time! But be honest are you still covered in cv grease ? 😂😂 hate the stuff
@theseldomseenkid6251
7 сағат бұрын
Who wants to clean the bearings and replace the grease anyway. I am sure the existing grease is just fine. LOL
@hermesmusician7327
10 ай бұрын
QUE....? Bro YA ESE GUARDA POLVO O CUBRE POLVO NO SIRVE.. dañaste todas sus propiedades de dureza y duracion.😢
@skippynj1979
8 ай бұрын
Cool.. very neat. For my personal cars. If I'm in there I'll just replace the axle with a fresh one.
@randybloomfield5090
11 ай бұрын
Or you could just get a new axle for 50 bucks 😂
@modifiedmechanix
11 ай бұрын
Lots of these newer vehicles are getting up towards $450 with a 4 month wait
@michaelharvey9552
10 ай бұрын
The right tool is everything.👍👍
@boraotomotiv6405
10 ай бұрын
Körüğü açtıktan sonra çok beklettin yırtılma yapar ve körüğü oraya gecirmenin daha basit yollari var 25 yıl önceden beri var bu sistem yeni değil
@pawebronek4329
10 ай бұрын
Toż nie można było wypiąć przegubu, oczyścić półoś i założyć gumę, osłonę pełną smaru nie rozdzierając jej jakimś "rozdzierakiem"? I mordować się przy tm, żeby to zsunąć? i kompresor do tego, węże itd itd. A tak nawiasem mówiąc, to jestem pełen podziwu, że ta osłona to wytrzymała.
@___ji__7050
10 ай бұрын
Пыльник шруса уже никогда не станет прежним😂🤣🤭 После таких манипуляций с ним,с уверенностью могу сказать что ему настал "пиздец" Хотя проще было снять стопорное кольцо😂😂😂
@frankorobinson1540
10 ай бұрын
So this has been around since the 1980s nothing new if you have a car thats not worth much and won't have long its a great alternative. But if its a nice car don't waste your time .the grease it contaminated now it will eventually wear out the ball and socket join in axel and the cheap rubber boots aren't very robust. The cv joint comes off faster than you can operate that boot stretcher just replace the joint and boot with oem equivalent.better yet just replace the whole axel. And not with those cheap Chinese axels that vibrate under hard acceleration right out of the box .theres never time to do it right but always time to do it twice😂😂😂😂😂
@sers6007
9 ай бұрын
И зачем так сильно растягивать? Всё очень грубо выглядит! Не профессионально как то!
@rocanroller85
Ай бұрын
UTI technician they can't do anything without tool. But they always have their certified in his hand.
@KvadroWok78
10 ай бұрын
😂😂😂😂до ворот гаража хватит этого пыльника 😂😂😂😂
@vlad_zapchastin
10 ай бұрын
Россияне ! Использовать только универсальные пыльники ! Брт и прочее не канает
@ИгорьСоловьев-я6ж
10 ай бұрын
Достаточно попадания одной песчинки в ШРУС и ресурс сократится в разы
@error404-r5u
10 ай бұрын
Шляпа! Не каждый пыльник пойдет!Тоненький как презерватив
@СталкерПулев
10 ай бұрын
Одна рука чуть чуть кривая ....а другая чуть чуть ниже спины....😂
@CreatingExcellence
8 ай бұрын
You’re one final step away from the removal being completed. Why would anyone do this?
@marcanthony854
11 ай бұрын
Doctors did that to me on the Last Trans-Anal resection 😮
@romazadov7457
10 ай бұрын
Типо песок не попал в шрус....главное пыльник новый поставить😂
@kevinoneill41
10 ай бұрын
Cool every DIY has one of these some where around his work bench.
@robertkrieger8394
7 ай бұрын
If you're going to replace the boot just take the axle apart clean all the old grease out put the new boot on repack it and put it back together
@noelopez9046
11 ай бұрын
porque se complican tanto la vida? es lo mismo y más fácil meter primero el cubrepolvo 🤦
@АбвгдЕжзийклмн-ж6п
10 ай бұрын
Это когда лень промыть и смазать шрус,😊работа на отешись😅
@Rafael...chiquinho78129
11 ай бұрын
Com ferramenta adequado chegar da gosto de trabalhar melhor ate achar a trava limpa a graxa tudo
@Guns6478
11 ай бұрын
É muito mais facil tirar o homocinetico que estourar a coifa pra colocar sem tirar o homocinetico
@ericeric9475
10 ай бұрын
Когда учился на гинеколога, а работаешь проктологом
@ВалерийНоргайло
10 ай бұрын
Зачем такая му-та-та , когда шрус снимается за 3 секунды?
@keithl9025
8 ай бұрын
Just replace the axle at that point, also who the fuck has that tool lying around?
@garymcconnell4379
7 ай бұрын
UUUUUH? Once your that far the axle comes out in about 8 seconds.
Пікірлер: 434