ive really not had very many problems with the Volvos, but when I did they are pretty high on parts and they have a high shop charge. as far as warranty work all my stuff is way beyond warranty
@astro1218
11 жыл бұрын
" Pipe finding teeth "
@MrMom4
8 жыл бұрын
any video of the new teeth in action?
@melaniew77msn
5 жыл бұрын
Not trying to be a critic but the welds around the shanks are wearing away. It might be time to just clean them up and weld them like 2 beads side be side all the way around each tooth. You are welding cast steel to the cutting edge so preheat to around 400 degrees and use 7018.
@w056007568
11 жыл бұрын
They look a ferocious set of teeth and will exert a great deal more strain on the bucket structure surely? Price = very expensive but ought to be some of the best quality Swedish steel. I think that it lasts longer than other stuff in my area of work (not construction work I might add!)
@1GuyGamingCo
11 жыл бұрын
chris im just wondering your thoughts on Volvo customer service, my dad and owner have a partnership in a paving company and we have bought a paver and a track steer off of them and we have had nothing but problems with both and they don't do anything for us nothing that they said was covered by warranty is actually covered, we don't plan on buying anything else from them but i just wanna know your thoughts
@gangesexcavating
10 жыл бұрын
I was getting a week out of a set of teeth on some jobs. Burnt right off. Big fan of the Esco horseshoe lock threaded teeth. Any tooth with rubber or urethane locks end up literally falling apart once you work in stump fires.
@specialks1953
11 жыл бұрын
You did a fine dentistry job on that bucket.
@letsdig18
11 жыл бұрын
really Id guess this tooth weighs 10-12LBS? I picked up the box with 5 and it wasn't that hard to carry
@bobmccann1886
6 жыл бұрын
450 big ones just for the teeth and pins!? How much do you charge per hour to run the machine?
@donald1056
9 жыл бұрын
You need a camera stand for this work!!!
@chrischerm1297
6 жыл бұрын
Should of considered some build up weld on those worn shanks before those new teeth...
@unknown1129
10 жыл бұрын
its seems to me that for the tooth pins there should be a cross linked retainer pin to keep that tooth pin in place
@diggerdave51
11 жыл бұрын
Good Video, Chris have you replaced the sidecutters yet ??
@Ghost23100
7 жыл бұрын
We rented a 210 for a concrete bridge tear out. When I got the hoe it was missing a tooth already so the company that we rented it from put a full set on. The bucket was so wore out that the new teeth wiggled with new pins. I didn't even get the the excavator off the trailer before a tooth fell off. The owners came out to the sight and tried to weld it back on and they decided to weld the other four. Long story short I lost two teeth and they have to buy a new bucket. That Volvo was very nice machine to operate. Very smooth and quick to respond. Cutting grade with a 2 inch was a piece of cake.
@letsdig18
11 жыл бұрын
id guess 1000 hours but ive done a lot of hard digging
@soldierofdirt81
11 жыл бұрын
You are dead right about the cost of the teeth and keepers, a set of tiger teeth for a bucket like that would be over $500.00 for sure
@slone465
11 жыл бұрын
hey Chris do u own the company or do u work for them
@stevehorne10000
11 жыл бұрын
Take one of your old teeth split it down the centre, you can then use the pieces to guide you rebuilding the shanks that are worn bad and the new teeth flop around too much
@allied1394
11 жыл бұрын
Moving that rock just destroys those teeth doesn't it we had a job this summer moving some big stone used our backhoe and excavator at that job and I checked the teeth on the excavator after we were done they were destroyed from the abuse good vid nice looking teeth perfect for some tricks nice pointy new teeth
@jimlong527
5 жыл бұрын
Learned something new today...and you got an upgrade.
@codykeel6575
11 жыл бұрын
How many hours you reckon you got out of the old teeth
@longearthworksllc
6 жыл бұрын
How do those stay on? Have you lost many?
@larrywiggins672
8 жыл бұрын
I'd be real careful with the new teeth to big could rip the boss right out .
@mushenji
3 жыл бұрын
The fun part is watching you install them not in you talking about it
@antonykahil
11 жыл бұрын
what year is your machine
@Sinister_Reaper
11 жыл бұрын
what model teeth are they
@OMBIC
11 жыл бұрын
man you should get a "go-pro" cam or what ever its called so you can strap it to your body, it would make for much better vids and make it ezey'er on you to film :) they are like 200 bucks
@TWICKY420
11 жыл бұрын
You got a knack for the videos dude
@melaniew77msn
5 жыл бұрын
At 100$ per tooth those would have been well worth hard surface welding. Lincoln Electric makes a good welding rod for this application called Wearshield ME or a good wire called Lincore 60. Too bad this machine has way too much power for 23 series JD those teeth can be gotten for like 6$ per tooth on amazon. JD's price is fair it is just a hunk of cast steel no finish machine work or finish grinding. Sorry Volvo puts the hammer on you so hard. Digginok sent me here!
@muckrunner308
11 жыл бұрын
The teeth in my bucket need a 1 ton vehicle mounted crane ir
@JimsEquipmentShed
11 жыл бұрын
My teeth bolt on, I haven't had to replace any yet, as I seem t replace the machines before the teeth get too bad. B-)
@pjs5191
11 жыл бұрын
Ya i'd say your doing alright if you can get 1500 hours out of them. The $400 might hurt initially but look how much money they'll make you in the next 1500 hours.
@muckrunner308
11 жыл бұрын
The teeth in my excavator need 2 men or a 1 ton crane to lift them on, they last about 2 weeks in hard rock mining, lucky I don't pay for them
@Deere2154D
8 жыл бұрын
should have been changed already. if you can see the shank you're asking for problems. and komatsu I find are easier
@zeldapace4068
7 жыл бұрын
Deere2154D x ft u
@MrMyboymax
5 жыл бұрын
Cat and Kom teeth are also reversible AND you can re use retainers many times. Probably not a country in the world where Cat type teeth are not freely available and dozens of pattern suppliers too
@jessenp20162725
10 жыл бұрын
Any more videos like this?
@samhouston2000
9 жыл бұрын
Did it "Single handedly " like a Boss.. I mean literally, his one hand tied behind the camera.. I mean hold the camera with one hand. I like people who know what they are doing..
@hphillips7425
5 жыл бұрын
I am retired but I would enjoy occasionally doing this type work. I would also like operating the equipment 😎😎
@george7021
2 жыл бұрын
Could you be interested sir, in a team-up, land clearing projects?
@waylondunkin3175
7 жыл бұрын
looks like you need some cutter blades
@Grumpy_old_Boot
11 жыл бұрын
Man, if I could get real teeth for that price, I'd be happy.
@UnitCrane514
11 жыл бұрын
Those are some wicked teeth!
@neftalirosado6167
8 жыл бұрын
No finish? 👎
@mrbluenun
10 жыл бұрын
Hi, And many thanks for the upload of a very interesting video. Seen a few before on this but none as detailed, thanks. Take care mrbluenun
@copperheadmarine
11 жыл бұрын
I like that design of keeper! The Cat keepers are a BITCH to get out!
@LaSouthernGemini
8 жыл бұрын
Good job on the video.
@Pete379andCat3406
11 жыл бұрын
damn what some teeth this time
@leonardo1480
9 жыл бұрын
My god, $400 odd just for the teeth, that just as expensive as going to the dentist
@Deere2154D
8 жыл бұрын
that's cheap. I don't know what they cost for the one I run but can pretty much guarantee damn near double the price and it only has 6 teeth
@leonardo1480
8 жыл бұрын
why are they so expensive? if I had a machine that needed teeth a expensive as that I probably be tempted to build a forgery and cast my own, I feel so sorry for guys that have to pay that kind of price for them -- all the best my friend
@wspycher1006
8 жыл бұрын
Mine would be expensive just for the fact that I'm in a 80 ton class
@brownwarrior6867
6 жыл бұрын
wspycher100 have you tried the F-Plan?
@Simonsimps
11 жыл бұрын
Have you retired ? No video's for a while :|
@1693caterpillar
9 жыл бұрын
These teeth will lower the bucket breakout force,not increase it. There two long.
@benjammin4456
7 жыл бұрын
1693caterpillar site your source
@dman2188
4 жыл бұрын
Obviously it depends on the angle of attack .. if pulled towards the operator and slightly level it will cut through with less force than a blunt worn out one .. just use a little common sense .. a spade shovel thats new or one that has a 1inch round bar welded on the end .. now go shovel dirt
@rogerdrum5936
7 жыл бұрын
I think I'll send you some screw drivers. You must be about out by now. They are a universal tool. Lol
@equipment859
11 жыл бұрын
moore demo
@gangesexcavating
11 жыл бұрын
Don't buy a Volvo. Their dealer support is terrible in British Columbia, Canada. Are you reading this, Great West Equipment? Your support is the shits.
@sorenslothe
10 жыл бұрын
So you get 1500 hours out of these teeth, and you think $450 is expensive? It's about 30 cents an hour for those teeth. If you work jobs that poorly paid, you need another job :-)
Пікірлер: 70