I've never worked on a Forrrrr. Foooo. FFFFF... I can't do it. LOL
@3Wheels1Block
5 жыл бұрын
I like the video based solely on the intro 😂
@TheDaninator
5 жыл бұрын
3 Wheels & A Block Dad always said it wasn’t nice to say the four letter F word. 😂
@jonathangarzon2798
2 жыл бұрын
Where'd you get the torque rating for the bearing nut?
@assog5737
2 жыл бұрын
Ford. F#$ked Over Recycled Dodge. LOL 😂😆
@AWZ247
5 жыл бұрын
Thanks for including the torques needed. Most leave that out.
@Jcorpus02
Жыл бұрын
I’m extremely grateful for this video! I have a 1999 Ford Ranger and I changed the rotor all by myself following this video. I’m can’t believe I actually did it. This “mechanic” came and tried changing them and he was missing parts. The inner bearing and the wheel seal.. When I checked the rotor was completely loose, almost falling off. It was making such an ugly noise like a screeching sound and he said it was because they were new brake pads and rotor but I just knew something was wrong.. my tire almost fell off. He put the outer bearing in the inside and it was completely broken when I took the wheel off. This video saved me so much money and I learned so much. So thank you! I felt like such a badass cuz I did this all on my own lmao
@RK-dk7bw
2 жыл бұрын
Great video. Best and most informative one I've found before doing my rotors and pads on my Ranger. Thanks guys!
@wrigh003
Жыл бұрын
Video's great. 101%. For others who may watch - note that some rotors have the REAR bearing race preinstalled too. And in that case, if you put the supplied race in over top of it (where it fits and seems it should go, probably useful on a different application), nothing will go together, you'll wonder "why your rotor is 1/4" too tall for the application, dang it (supplier)," etc. But then the OBVIOUS SOLUTION will slap you in the face and all will be well. So, uh, I heard some guy did that. :D
@jeremyrainwater2175
9 ай бұрын
Huh????😮
@oo0Spyder0oo
5 ай бұрын
Yeah this already had the rear race in it as well so your point is moot. He only tapped in the rear seal.
@chrisf9738
11 ай бұрын
Thank you very much for including the parts and torques in your video. It made using Rock Auto that much simpler. I understand the rash. GMC guys are usually allergic to Quality. JK, I have a 2001 Suburban with the 5.3 Vortec. Rock solid engine. I love my Ranger too.
@thomasbreslin7759
3 жыл бұрын
Now that’s how you hand pack bearings perfect job !!
@RedWhiteAndBlueVideo
5 жыл бұрын
I just saw a quick tip. If your changing your rear bearing seal, loosen the castle nut slightly on the front and pop the rotor off. It will pull the rear bearing and seal right out.
@jeremyrainwater2175
9 ай бұрын
Wow! Ty
@Yophillips3272
2 жыл бұрын
I just reused the old bearings they came out pretty easy. Everything seems to be working as it is should.
@theonlybutterflylady
5 жыл бұрын
Thank you for making this video, I'll be needing it VERY soon, got my new rotors that I was told already HAD the bearings in it only to find out....... they aren't so now I gotta get the bearings and seals hopefully after she makes it home from one more night of work.......
@kenoger2866
5 жыл бұрын
Nice fix Dan. I always drove chevrolet and oldsmobile when I was growing up so that's what I was used to. Then a relative left me a grand marquis when he passed and working on it was like entering a foreign country. It's been a good car though and fun to learn .
@TheDaninator
5 жыл бұрын
Ken Oger Foreign country 😂 that’s a good way to put it. 👍
@marv.mon.9845
3 жыл бұрын
Great straight forward video! Informative and easy. Thank you bros
@fixitdanner
5 жыл бұрын
Great opening!
@fza.digital
2 жыл бұрын
Super simple now I need to do this tomorrow
@Playitstraight44
3 ай бұрын
The biggest contradiction I see is on the setting for tightening the nut is one mechanic says 40 inch pounds and you state 240 inch pounds. Thats a big difference.
@TheDaninator
3 ай бұрын
We were following the numbers stated in the repair manual. 🤔 interesting.
@paulshuppert4975
Жыл бұрын
Check slide pins for self centering caliper..make sure they move good ..if not take them apart and fix
@ernestoguzman3697
Жыл бұрын
Muchas gracias me sirvió mucho el tutorial
@midmooutdoors7556
Жыл бұрын
Having a bearing a seal driver kit comes in handy on old shit like these rangers
@mikewikowski3032
4 жыл бұрын
Thank You..Man O Man guys Ty a Billion...
@salvadoralvarez2093
Жыл бұрын
Buen video.cualbes la entrada delos baleros.. cual parte entra i.cual parte es por fuera.
@huntermccarty426
5 ай бұрын
Did you jack it up on the suspension beams?
@toddnichols3117
3 жыл бұрын
in re: info provided at 4:37... as of 9/22/2020 the indicated part is $46.79.
@johnsipes4422
Жыл бұрын
I’m gonna do this on my 1999 ford ranger 2wd. I’m replacing the pads and rotors on the front. And I plan on replacing seals and bearings. Is it two bearings per side and one seal per side or is there two seals on each side? Basically what I’m asking is how many bearings and how many seals will I need total?
@MicRuLerZ
Жыл бұрын
There's an inner and outer bearing for each wheel
@michaeld.3779
Жыл бұрын
Did you put the reservoir cap back on?
@erikmendez1302
2 жыл бұрын
Can you reuse the same seal from the old rotor if you’re using the same rotor? Pliz help 😅 thanks
@Mekhanic1
3 жыл бұрын
You should pack some grease in the hub before puttin the outter bearing. Also you may have had too much torque on the spindle nut. It should only be finger tight (with a socket and no wrench).
@_s827
4 жыл бұрын
I just did this on one wheel (thank you for great video) and noticed that there's a huge difference between how freely the new rotor/bearings spin (mine looks just like the video) and how freely the opposite wheel spins. The old opposite wheel (the one I didn't work on) spins much more freely. Is this a sign that bearings are worn or is this normal wear?
@TheDaninator
4 жыл бұрын
The old bearing will spin more freely because it's got wear on it. If there's any play in the hub (not tight), then you'll want to replace it. Worn out bearings can cause premature tire wear.
@21stcenturyfossil7
4 жыл бұрын
The wheel bearings drag more when they're freshly packed with grease. They will spin some grease out as you drive and then spin more freely.
@_s827
3 жыл бұрын
@@TheDaninator thanks!
@yehudaegert2276
4 жыл бұрын
ok. now for us normal people who dont change the whole hub "just because", how do we get out the old and put in the new race??
@toddnichols3117
3 жыл бұрын
I did mine with a hammer and screwdriver to remove the old chases, and a large socket and a hammer to put the new ones in. You need plenty of patience too.
@docbrown303
3 жыл бұрын
Large punch and big hammer i have done plenty on big truck
@norbertrivera
10 ай бұрын
240in/lbs = 20f/lbs and 20in/lbs = 1.6 f/lbs -so this is the final torque,only 1.6f/lbs?
@MichaelPetty
7 ай бұрын
From what I have seen in other videos, they do an inital torque to 15 ft lbs, back it off, and torque back to 2 ft lbs. A lot of torque wrenches do not go below 10 ft lbs.
@alexanderrineman2413
3 жыл бұрын
What if I can’t torque to desired pounds
@dazzargilmour
4 жыл бұрын
what size socket did you need to use to set in the seal please??
@ronjose51
4 жыл бұрын
dazzargilmour I believe it’s 24mm
@sesapup
4 жыл бұрын
@@ronjose51 27 mm
@dragon77721
Жыл бұрын
I wanted to do things perfect so i mad sure i watch your video then I took notes. when i tighten the rotor bolt to 240 foot pounds something strange happen the bolt kept spinning ! Whats going on ? OMG !!!! You said 240 inch pounds !!! WTF is that....man i wish you would have made that clearer... Like this is inch pounds not foot pounds! So what damage did i do and how do i get that bolt out so i can replace it ? I cant find any info about this problem im now having ! Inch pounds when u could of just said 20 foot pounds ?
@SailOnFlyBy
3 жыл бұрын
Darn my abs light came on after changing everything out. Drives fine.... But light is on. Insight?
@Yophillips3272
2 жыл бұрын
Probably the wrong rotors. There's ones with 2 wheel abs and 4 wheel abs.
@poppa861
Жыл бұрын
Did you ever find out the issue
@georgelareese1086
4 жыл бұрын
Can you please tell me what size c-clamp did you use
@MUSTANG408W
4 жыл бұрын
C-clamp isn't required for this job. You can buy a cheap caliper spreader at the parts store. Use an old brake pad on the caliper pistons to push them both back in simultaneously with the spreader.
@apprenticetojourneyman2159
5 жыл бұрын
First comment 🚜🇺🇲
@jonathangarzon2798
4 жыл бұрын
Ya kept switching between ft/lb and in/lb careful of that, people who aren't paying attention to the details will screw up bad. Also sounded like you said main axle but was 24mm but the label looks like its in inches
@keithooo123
Жыл бұрын
so no need to use the races that came with the bearings, to pop off the ones on the rotors and put in press in the timken ones. i rather do it your way...but???.....anybody care to give opinion on that.
@cliff3321
4 жыл бұрын
20 IN/LB torque - saved you from watching the whole video... ya welcome.
@docbrown303
3 жыл бұрын
Wrong way to Do it
@docbrown303
3 жыл бұрын
You need a dial indicator, bring the bearing to 0,001" to 0,005" of END play
@tom.p1986
5 жыл бұрын
I hope you had a good long hot shower after working on that F***. Lol
Пікірлер: 67