To remove flywheel, position a punch on center of shaft, after removing flywheel nut. Strike punch with hammer, the shock will loosen flywheel. Remove by hand.
@dbaker3264
6 жыл бұрын
Light coat of RTV in the seal channels of the case both side needed as well. Hence casing seal and bearing channels are part of the molding, not a milled process to make sure they are perfectly round, so the light coat of RTV is needed in the seal case channels so the outside of the seals get fully seal to the case channels as well.
@daphlavor
6 ай бұрын
You’ve given me more courage to tackle my ms250, which needs a new piston & cylinder, great info on the visuals especially the sealant at the bottom!
@danhenderson783
7 жыл бұрын
The flywheel pops right off with a slight pry to the backside while tapping the loosened flywheel nut. Don't drill Hiles into it!!!! It is precisely balanced.
@crankshaft1053
4 жыл бұрын
Dan Henderson I just tap the crank with a hammer
@BobChanter
4 ай бұрын
Was balanced. Not anymore.
@johnclarke6647
7 жыл бұрын
just screw the flywheel nut on the shift a few turns and hit the nut with a small hammer, sharply, and the flywheel will usually come off the shift. if not try a BFH.
@lildonkey292
6 жыл бұрын
you should get a flywheel puller and crank case splitter . they make life alot easier
@BobChanter
4 ай бұрын
A crankcase puller is not needed in this job.
@Antonio-pd7tn
5 жыл бұрын
Неплохая бытовая пила , мягкие амортизаторы , приятная работа двигателя . В хозяйстве с 2008 года .
@roystheboy
3 жыл бұрын
I had a customer that replaced hes own crank case and piston rings but engine fires but wont run unless I'm holding the throttle in and cuts out even when the throttle adjustment is on full, I did a compression test only showing just over 25 carb has been cleaned this one has got me
@neddy1287
Жыл бұрын
Well the compression should be well over 125 psi but you mentioned 25psi usually means there's air leak somewhere on the engine. Or worse case the cylinder head, piston and rings are shot. To get compression to come back you would have to clean the bore with two stroke oil and a lint free cloth, clean the piston ring gaps for crud buildup and clean the rings as it needs to be moving. I have heard of sticky rings stuck to the piston resulting extremely low compression or holding the pull cord letting the chainsaw free falling on it own as signs of dropping too quick is lack of compression. That all I can think of due to my brother asking me 101 questions of why it not working for him
@timsturgill3617
5 жыл бұрын
We do repairs on chainsaws & I learned from this video
@moeenahmed6853
10 ай бұрын
Hi. Where did you get the sealant from and what is the brand called??? Can you use any sealant which is heat resistant?
@claudiocorigliano8493
8 ай бұрын
Ciao, interessa anche a me questa informazione
@stevewrightington1583
6 жыл бұрын
put the nut back on flywheel a few turns and put socket on nut hit with hammer two taps flywheel will pop right off
@leogagnon5339
5 жыл бұрын
Exactly what I was about to comment... simple fast and easy
@crankshaft1053
4 жыл бұрын
I just tap my hammer in the crank
@Mike-tg8gl
7 жыл бұрын
I enjoy watching your videos.
@DonnDIY
7 жыл бұрын
Thanks, buddy!
@Wcf-qn9ip
5 ай бұрын
Great video. Thanks
@tm171717
4 жыл бұрын
Great video, thanks.
@KentuckyFriedFixes
2 жыл бұрын
This is a great video. I can see why its gotten over a quarter million views. Good stuff.
@johnclarke6647
5 жыл бұрын
Just run the flywheel nut down until it is flush with the top of the crankshaft and hit the end of the nut with a brass or hard plastic hammer while putting upward pressure on the flywheel. I use small pry bars to to that and the flywheel, after a few raps, will pop loose. They do make flywheel pullers but they are specific to each model of saw. I just do the rap method. With the nut screwed on to protect the threads on the. Rankshaft.
@sergeyprohorov1659
4 жыл бұрын
Магнето снять минуту, на 1/3 откручеваешь гайку , берешь за магнето пальцами , приподнимаешь за магнето пилу и по гайке резко молотком бьешь.
@user-yd1oe5tj1u
3 жыл бұрын
Так только наши умеют)
@geedubb2005
7 жыл бұрын
another awesome project Donn!
@DonnDIY
7 жыл бұрын
Thank you, Gee!
@danhenderson783
7 жыл бұрын
Should do a simple vacuum test on the engine before tearing into the saw.
@jacoblang2712
5 жыл бұрын
I just love my 021
@JamesParus
7 жыл бұрын
yep, getting two stroke to start and run with bad seals is very hard.
@DonnDIY
7 жыл бұрын
It did start eventually with the choke fully on though. But yeah, the joys of two strokes... :D
@AndrewBrowner
6 жыл бұрын
atleast it could be fixed for 10$.. a 4stroke will cost alot more when you get into oil seals and pumps and valves and rockers ect 2stroke small engines are the way to go if youre gonna fix them yourself.. if youre paying someone to fix them go 4stroke as 2 strokes typically have an issue yearly where 4 strokes can be quite reliable
@clearlakebunch8569
Жыл бұрын
Excellent very helpful I have question on Seals my old seals are ones brown the other is blue Why// why are they called soft seals and hard seals and if they are different which one goes where??
@perkypat2214
6 жыл бұрын
How did you stop the crankshaft from turning when you loosened the flywheel nut?
@gonkeyhughes
3 жыл бұрын
I put parra cord in top of cylinder through the spark plug hole about. 2 foot leave a bit hanging out and it traps piston on the head. After undoing the nut pull cord out easy
@dstevenpaisley
7 жыл бұрын
we use a match book cover to set clearence
@bborkzilla
7 жыл бұрын
I've used a good stout business card for the same purpose!
@Wanous-hv7zo
7 жыл бұрын
D Steven Paisley i use the Stihl tool
@phillipkramer6638
7 жыл бұрын
You really had to get into that thing to replace those. Think they should be made of some special material instead of just any type of plastic or rubber like I have seen on different brands.
@jdailey19811
6 жыл бұрын
Phillip Kramer this is typical of the homeowner series of saws. The pro series has easy access to the top end bolts on top and can easily replace the top half an about 2 hours, if you know what you are doing. The homeowner series engines can be fixed, as proven here, but takes more time to get into everything. If you have the know how, you can take a homeowner model and replace things and they will last a lifetime, if you use them for what they are intended for.
@magicone9327
3 ай бұрын
Please don’t go through this type of flywheel removal technique. Just put the nut back on the shaft so that it can be hit upon without hitting the threaded end of the shaft. Get a brass drift punch to hit the nut with. Place a wide blade screw driver or similar under the flywheel at a magnet location and against the main body at the top of flywheel. Apply slight leverage and wack the nut using the brass drift with a hammer. It will come off!
@olivierj.2435
3 жыл бұрын
Don't forget to use gaz resistant gasket maker
@ciftsarili
3 жыл бұрын
Nice job👍
@JuhaErkkila
7 жыл бұрын
This was cool. Have to do the same for my 026 some day! :)
@DonnDIY
7 жыл бұрын
That's funny, I have my 026 (MS260) waiting in the line for a top end rebuild and crank seals replacing. I will make a video of it for sure. Stay tuned. :D
@JuhaErkkila
7 жыл бұрын
You can bet on it.
@same9090
6 жыл бұрын
very good video
@DonnDIY
6 жыл бұрын
Cheers!
@marcb8874
6 жыл бұрын
THANK YOU FOR THIS video but you change the segments, and the grooves on the cilyndre what do you do? I ALSO SEE BEARINGS open without grease? I AM TR7S SURPRIS are they greased by the oil of the mixture?
@robertstroh4803
4 жыл бұрын
Yes the oil in gas lubes bearings .if you think about it kinda amazing that they don't burn up
@phillipkramer1897
6 жыл бұрын
I hope you cleaned out the exhaust port at top dead center
@fu420b9
3 жыл бұрын
Omfg to the drilling.
@phillipkramer1897
7 жыл бұрын
Did you dirco the outside flanges of the seals and grease the insides? I also was surprised to see you didn't use a feeler to gap the coil.
@robertyearian227
4 жыл бұрын
How long did the changing of seals take
@DonnDIY
4 жыл бұрын
One evening.
@AndrewBrowner
6 жыл бұрын
i assume the flywheel only goes on the crankshaft one way so theres no timing settings as long as those two parts are bolted together the sparks timed properly?
@DonnDIY
6 жыл бұрын
Yes, it goes on only one way.
@mimiporsche
7 жыл бұрын
Bravo you have replaced the crankshaft oil seals! The ball bearings were good?
@DonnDIY
7 жыл бұрын
Bearings were good.
@vwtaro
2 жыл бұрын
What was the problem Don?The saw won’t start?
@musurmonergashov1298
3 жыл бұрын
Good job nice
@isotsakov9159
4 жыл бұрын
Very good
@DonnDIY
4 жыл бұрын
💪
@garengtutorial8923
Жыл бұрын
Keren bos
@dejan9713
6 жыл бұрын
How long you wait usually after aplications of gasket sealer?
@DonnDIY
6 жыл бұрын
24 hours is usually said on the sealer tube. Check what your label on the sealer tube says and act accordingly. ;)
@Adam-xs3ng
7 жыл бұрын
good video, really clear video with good focus, what camera do you use¿
@DonnDIY
7 жыл бұрын
Nikon Coolpix.
@AYALARAMON100
6 жыл бұрын
Nice video
@AFHProjects
7 жыл бұрын
Good work! :)
@DonnDIY
7 жыл бұрын
Cheers!
@dstevenpaisley
7 жыл бұрын
I have a 034 that's going to need seals .flip it to cut a tree runs like hell works all right blocking wood.How long did it take you to do? I know the 034 is way different than that saw but gives me a idea!
@DonnDIY
7 жыл бұрын
It took me a whole day basically. If I had known in the first place it needed new seals it would've taken less time.
@nygardenguru
6 жыл бұрын
Danka shein
@bonsaitree1350
7 жыл бұрын
Runs like a champ! Does gramps get it back lol
@DonnDIY
7 жыл бұрын
My grandfather already got it back. He has a new saw already so it's unclear whether he will use it or not.
@sthilthemiracleofalteratio9572
3 жыл бұрын
А как же опресовка?
@chiranagheorghitaeugeniuth98
3 жыл бұрын
you could take those seals apart just by prying them out. no need to tske engine apart. But good job overall
@nadingjeff
6 жыл бұрын
Awesome.
@nutmeggrove8429
6 жыл бұрын
Nice.
@roxy-tj3jo
2 жыл бұрын
What does RTV mean
@andrewklein2349
2 жыл бұрын
Room Temperature Vulcanizing
@jfox9317
7 жыл бұрын
What was the red sealant you used.
@DonnDIY
7 жыл бұрын
Some generic engine putty.
@jorangel87
Жыл бұрын
@@DonnDIY how long you let sit before installing together?
@agritechnicsvideography5497
7 жыл бұрын
You are a genious
@wojciechostrowski3686
7 жыл бұрын
fajny film
@fendtonafarm8513
7 жыл бұрын
Nice! How old is the chainsaw?
@DonnDIY
7 жыл бұрын
Probably around 7 years I think. I remember the time when his previous Husqvarna blew the piston and he bought this one new.
@Junk4508
7 жыл бұрын
what are you use oil?
@DonnDIY
7 жыл бұрын
For the fuel mix my grandfather uses special Husqvarna oil, those little bottles pre-measured for 5 L of fuel. I used some generic oil while assembling the saw just to make the piston and cylinder more slippery.
@usaisalwaysnumber1
5 жыл бұрын
word of wisdom REMOVE THE CHAIN AND BAR FIRST...save your hands..
@carloscosta1280
5 жыл бұрын
Esse eu vi desmontando
@Chogall3295
3 жыл бұрын
Blue chinese seals... why?
@richardschofield2201
2 жыл бұрын
My original Stihl seals are blue from the factory
@Chogall3295
2 жыл бұрын
@@richardschofield2201 Original is between violet and blue.
@bradleyhofer4474
6 ай бұрын
👍🏽
@125dan6
7 жыл бұрын
cool !
@DonnDIY
7 жыл бұрын
:D
@Wanous-hv7zo
7 жыл бұрын
take the china bearings out while you are at it
@leoramirez4024
6 жыл бұрын
Go get parts from the web site called sawzilla they have much better prices and quality parts good luck on your next project
@jdubya54
5 жыл бұрын
Next
@punchogunter2362
4 жыл бұрын
You didn't show that you supposed to lube the cylinder wall and you didn't provide how long the gasket sealant supposed to set up before installation of everything else! Plus provide torque specs for screws!
@usaisalwaysnumber1
5 жыл бұрын
no grease in the seal lips installing them? no dirko on the outside of the seals? I SMELL AIR LEAK...
@user-zs9ht6dp1j
4 жыл бұрын
Я понял,что нехера непонял.
@fredo50250
5 жыл бұрын
wtf l'arrache volant
@johnkosheluk1041
6 жыл бұрын
By your self a knock off i am a cirtfide stihl tech
@ivamsousa9275
6 жыл бұрын
..beya
@gouran21
7 жыл бұрын
Clear this filtr ;---------;
@DonnDIY
7 жыл бұрын
Air filter isn't dirty, it only looks like it's covered with saw dust.
@alexandarpenchev7162
5 жыл бұрын
STILL 0 23 nombar1
@filipandonoski25
6 жыл бұрын
haha funny why u take off engine to change a bearing cap ?? that problem why chainsaw no start ?
Пікірлер: 120