I did mine in the 97 RS a few years ago. It was $300, came out of a garage kept 60,000 mile car. Nice car, I hope to have my daughter's new 99 firehawk home soon.
@davidme8623
Жыл бұрын
Thank you for the video, I was worried about the clip location on the side plastic pieces, and didnt want to break them. I was able to see them in your video. Take care. I know how to fix your cracks in the door panel so they are invisable if you want to know how. I was able to do it on mine. First of all release the staples that hold the rubber window molding to the door panel whether your panels are cracked or not. When the rubber gets hot it expands and causes pressure on the plastic, after years of expansion and contraction the crack starts. By removing the staples, the expansion can occur without placing any pressure on the plastic door panel.That is the cause of the cracks. You only need to remove the one or two next to the end of door, past where the crack has formed. I did it to mine about 10 years ago, and the slight crack that had started on the drivers door, has not gotten any worse. I was able to fix the passenger door that cracked almost all the way thru. The trick is get some metal lattice at home depot, cut a section to go behind the door panel and extend from one side of crack to other. I did about 2 x 7 inch piece. I lined up the crack and put a very small drop of super glue on the crack from inside of the door so it would not be seen from outside to temporarily hold the crack together. Its very weak so dont put any pressure on it. Its also helpful to plan how you are going to lay the door panel down so there is no pressure on the crack. I used some towels and a board to support it underneath. Once you have the panel glued and layed down, place the metal lattice, I bent mine so it would so it would follow the curve of the plastic and sit pretty flush against the back of the panel. Evenly space it across the crack. Get some bonding glue like JB weld, but make sure it is the kind that does NOT set up to being solid hard. You want the type that remains a bit flexible to give and take with expansion and contraction of the plastic, or it will eventually break the bond. Do not put the glue directly on the crack, you can be close but not on it because it may soak thru and show on the outside. I did this about 10 years ago and mine has held since then. I live in a hot area that temperatures reach over 100 F. I was going to make a video about it, but it hadnt stood the test of time, and it was an experiment. But I am proud to say it has worked this long, and you still cant see where the crack was, unless you really look for it.
@mikes.1882
3 ай бұрын
I have a 95 z28. I have a buzz in the dash I believe caused by sonic induced vibration. Anybody ever Conquer this issue?
@sabaisabai8895
3 ай бұрын
I have the same problem😔 (Pontiac Firebird V6/1994) Now I can solve the problem.☺ Thank you for the video.👍Greetings from Austria
@solidtenpin
2 жыл бұрын
I put an ABS overlay on mine, and when I was removing the weights the next day (to hold it down so the silicone could cure), I dropped one on the dash above the steering wheel and cracked it, lmao. The overlay ended up warping from the Florida sun, so I just ended up putting my carpet back over the whole thing. Some day I would like to fix that crack and also attach studs to the ABS overlay and just replace the entire dash pad with that, since the ABS plastic is much more durable. Any OEM pad will eventually turn to candy and shatter again anyway.
@angeldiaz-gv8uk
3 жыл бұрын
Your car is gorgeous
@timmahoney9207
Жыл бұрын
Excellent job!
@bobbyprd
4 жыл бұрын
Nice to see your 4th Gen back on here dude!
@errinbrown4170
4 жыл бұрын
I would also like to know how you did the front splitter. Especially the stainless braces. It’s looks great. I enjoy your videos.
@3rdworldjo183
3 жыл бұрын
Fixing up my grandfather‘s 93 Trans Am this video helped a lot thank you nobody I knew knew how to change the dash and the only person I know to ever do one was my grandfather and when he did it he busted the fucking windshield out to do it😂😂😂
@SKRooU2
2 жыл бұрын
I didn't realize how thin and flimsy those pads are. And $300 for a used one ? Damn LOL I removed the pad on my IROC to remove the speakers and it was thick and made well.
@HondaATC330R
3 жыл бұрын
Nice car!!
@romero.4089
4 жыл бұрын
Finally found a new channel to watch
@AllTimePerformance
3 жыл бұрын
Thanks for subscribing. More to came!
@romero.4089
3 жыл бұрын
@@AllTimePerformance 🔥🤝
@patricksharkey4669
2 жыл бұрын
Nice job & very informative.I have to hunt one down for my 98 camaro.
@theessence2440
2 жыл бұрын
Hands down best f body car ever made
@brandonhodnett5420
4 жыл бұрын
Great videos man I really appreciate em, hey where did you get the ground effects for the sides? They look great!
@collectiblemotorcar
Жыл бұрын
Great video!
@michaelcobb4814
3 жыл бұрын
Nice work! I know how intense projects like that can be! 👍🏻👍🏻
@DennisWilliams-nf2gn
3 жыл бұрын
Something about Pontiacs in red or black!
@petersheamorris4852
Жыл бұрын
I LIVE IN ATLANTIC BEACH NORTH CAROLINA I GOT A ANOTHER ONE OF THOSE DASHBOARDS AND IT'S NOT BUSTED THIS IS PRETTY MUCH THE SAME THING AS YOU GOT IF YOU WANT IT
@keilylmm6377
4 жыл бұрын
Your trans am looks great.. I where did you purchase the dashboard? I have a 94 Pontiac Trans am that I'm restoring. I have the front windshield out of mine cause it's getting prepped for a brand new paint job.. I'm replacing the entire dash panel and the upper dash pad..
@thehegt
Жыл бұрын
Nice engineer all hard plastic vs the sun shine
@peterwindle4453
3 жыл бұрын
I had to do this with a right hand drive 98 Formula... imagine what a pandora's box that is... (still in pieces now)
@3500camarz
2 жыл бұрын
Dash pads are so expensive these days to replace. I think I bought one for an older F body in 2012-2013 for around 300. Last I looked I saw them going for 500-600 new on eBay!
@Someguy6571
7 ай бұрын
Gotta be careful with the ones on eBay as there is a lot of repos that are not factory original
@bobvires9650
Жыл бұрын
Nice car man!
@408civettethreat
2 жыл бұрын
Excellent video! Beautiful bird! Gotta ask what type of seats an where can I get a set? Lastly low profile seats make it easier to get in an out of or harder? 🍻 subscribed
@AllTimePerformance
2 жыл бұрын
corbeau and yiou can get them on there website
@somebody2409
Жыл бұрын
Where'd you get your white shift knob? 👀
@NJRangerGeorge
Жыл бұрын
Hi question what brand are them rims do you need spacers also how much do they cost
@ricardogonzalez8509
3 жыл бұрын
Beautiful fucking car my guy
@AllTimePerformance
3 жыл бұрын
Thank you.
@mikesimard47
3 жыл бұрын
Good work
@AllTimePerformance
3 жыл бұрын
Thanks
@7BigEasy
Жыл бұрын
You have same colour of grey is that “medium grey?” Colour code
@smokeypupper6145
3 жыл бұрын
when i replaced mine i took off those clips they are unnecessary and useless. pretty much makes it impossible to take a good dash pad out once it is clipped back into place
@leeleses
3 жыл бұрын
What holds it in then? Velcro?
@lincolnls0416
Жыл бұрын
So the dash pad out of a Camaro fits Pontiacs Firebirds, Trans Ams?. What about side mirrors?. I bought a 99 Firebird. This helps. Thanks.
@AllTimePerformance
Жыл бұрын
yes they are all the same. on the 4th gen's
@tony1978mj23
3 жыл бұрын
Where did you buy the dash pad and the seats
@JonuhOfficial
2 жыл бұрын
Seriously where do you buy the dash board?? 😭 my Camaro’s dash is shattered. I had no choice but to throw is away
@legalizitt
3 жыл бұрын
Where did you find an OEM replacement, and how much did it cost you? I have a '94 25th and my crash pad is cracked and broken, too.
@AllTimePerformance
3 жыл бұрын
we got it from a guy we meet will buying a car he had all type of 4th gen parts
@ttspeedster8930
3 жыл бұрын
😎👍🏾💯🔥
@phoqueewe7230
4 ай бұрын
Pontiac really cheaped out on the 4th gen. It's a shame...
@2H2521
2 ай бұрын
GM cheaps out on everything.
@music7arts
2 жыл бұрын
On my car my dash is still good but wanted to get it wrapped so it would be like brand new love to carbon fiber it. No one wants to touch it because of the Airbag. Maybe let us all know what you did. Thanks... I even offered to pull it out of the car but people are scared to touch it.
@AllTimePerformance
Жыл бұрын
The upper dash bad has nothing to do with air bag
@porfiriacalderon4014
2 жыл бұрын
Buy a small compass to cover it up.
@MW-yd4nk
3 жыл бұрын
great video..hey any idea how to get the A/C vents out and replaced?
@AllTimePerformance
3 жыл бұрын
I don’t I’m sorry.
@b30stm
3 жыл бұрын
Are those deep dish c5 wheels? What size? Sweet car
@AllTimePerformance
2 жыл бұрын
18in
@Bilcoop62
2 жыл бұрын
What kind of seats do you have and where did you buy them. Thanks
@dezbigguns1072
3 жыл бұрын
Oh yeah
@brettbrannon4775
4 жыл бұрын
I’ve been looking for a splitter like that on the front of ur ride. What brand is it and the ones under the side skirts?
@khristopherstevens1794
3 жыл бұрын
Where did you get the front splitter and body under skirt from? ...not sure if I missed the answer.
@carlaskillings4312
5 ай бұрын
Why not get the T tops out of the way, take them out till you’re done
@playingletters
2 жыл бұрын
Turbo
@alessioruiz3186
4 жыл бұрын
How much horsepower is your car pushing
@AllTimePerformance
3 жыл бұрын
not sure it shouldn't be much over factory
@14navi
3 жыл бұрын
Is it possible to remove a good dash pad without cracking it?
@AllTimePerformance
3 жыл бұрын
Yes just have to be very careful.
@jpontiac4294
2 жыл бұрын
Why not just remove the tops ? Great job. Anyways car looks sweet. I would personally put bondo to stop further cracks and another set of gauges.
@sucapizda
3 жыл бұрын
The vids are always awesome as long as they have a Gen 4 Trans Am in them. Ass soon as you switch cars, the channel will die. Just like Kenny Slides. Sorry, thats just how it goes. So no choice but to keep the trans am.
@AllTimePerformance
3 жыл бұрын
the car has been sold for a good min but we have a 3gen Camaro to
@billejeanfoxx3602
3 жыл бұрын
Thats the same color and year I have
@dylanlong2911
2 жыл бұрын
Where does one find a new dash pad!?
@AllTimePerformance
2 жыл бұрын
It’s hard to find f body dash with out paying a arm and leg
@redflag5512
3 жыл бұрын
I never understand the fn carpet people put on the dash!!! And if you keep carpet on why worry about the crack
@playingletters
2 жыл бұрын
😉...thes may car cinc 20 years
@marianogarcia3025
3 жыл бұрын
Where you get the dash pad? Thanks
@billejeanfoxx3602
3 жыл бұрын
What kinda seat belts do u have
@TheEnjoiSkateLife
4 жыл бұрын
Where did you get the new one at ?
@AllTimePerformance
4 жыл бұрын
NeK from a guy on Facebook market. You can buy them from HAWKS MOTORSPORTS.
@MW-yd4nk
3 жыл бұрын
@@AllTimePerformance got our at Hawks also..haven't tempted to put it in yet - not looking forward to it..
@abdrielsoto2020
2 жыл бұрын
We're did u get it?
@jeramiahvelazquez6746
4 жыл бұрын
Where did u get those seats from??!!!?
@AllTimePerformance
4 жыл бұрын
King Savage corbeau.com
@AwesomeFinish
5 ай бұрын
GM and Dodge just can't make a dash that doesn't crack
@burnzillablue
2 жыл бұрын
That car was not that well taken care of, its its an average example of those cars.
@davidfusco6600
3 жыл бұрын
The gauge pod is uglier than the damaged dash.
@Chevy_Guy
2 жыл бұрын
Took longer to find the screwdriver than to replace the dash pad 🤣
@sucapizda
4 жыл бұрын
Just put MAGA decal over that dash rip. Done.
@AllTimePerformance
3 жыл бұрын
LOL Good Idea!!
@MW-yd4nk
3 жыл бұрын
man, we need to keep that going..we are screwed the next 4yrs
@vermin1970
3 ай бұрын
Make Firebirds great again 😂
@troycasarez1215
2 ай бұрын
Where did you get the dash pad ?
@lazylion420
2 ай бұрын
ugh.. please don't mix politics and muscle cars you fuckin boomers 🙄
Пікірлер: 92