I sent you only 10 bucks but I really appreciate your assistance it made my job so easy!!!
@AhmedTaha12392
2 жыл бұрын
Peace be upon you, I am an engineer from Yemen, the same problem happened to me in several cars, American specifications, Korean cars, the holidays with the code is p1326 and p0326 I did not like checking the computer at all, and the solution is the same piece that you replaced. Thank you very much for your creativity in solving the problem without insisting on replacing the pieces. Which the computer requests, thank you Ahmed Taha Al-Yaman
@JohnDoe-vr1fc
2 ай бұрын
Best video for this issue ever!!!
@pjefsquad
11 ай бұрын
This is perfect , best video and that’s without taking off the radiator and stuff like other videos.
@mikemurphy5655
Жыл бұрын
awesome video, straight and to the point.Thank you
@edman1015
2 жыл бұрын
I have seen other videos where some code readers can't get the P200A (Intake Runner) and some can. Then you get these other codes that don't relate to the problem at hand. Maybe Kia and Hyundai have a computer read-out problem?????? The P1326 code (knock sensor - Rod Bearing Clearance) also has a similar performance condition to limit acceleration like code P200A (intake runner) limits acceleration also. I have seen other videos where Techs get a code P1326 (knock sensor) but replace the intake runner motor and it fixes the problem. Why didn't they get a code P200A for the intake runner motor??
@DULLAHGOSOHARD
2 жыл бұрын
That's crazy but i think it have to do with the computer and there company Data base because i use 2 different computer and get 2 different code and if i wasn't updating the main shop computer i wouldn't have found it
@edman1015
2 жыл бұрын
@@DULLAHGOSOHARD Keep up the great work - thank you for the reply
@mafazullah8478
2 жыл бұрын
I have the same issue p2600 and what can I do now
@mubarakissa7033
Жыл бұрын
@@mafazullah8478 Do you notice any failure in the performance of the engine?
@sergiomejia9700
Жыл бұрын
Did you do an ECM update? I replaced the VCM and have been told it needs an uodate
@JohnDoe-vr1fc
2 ай бұрын
You’re good bro!!!!
@geralddelescavagejr.7554
8 ай бұрын
Thank you so much for this video/ would this also have caused a blinking check engine light? My car died/lost power while I was driving it- I couldn’t go over 40 then I just couldn’t go- now it won’t start- I’m hoping this is the issue- I also heard the noise you explained in the other video so I’m really thinking it’s one of the gears from this part
@rodrigozunigajr2382
Жыл бұрын
I have a 2016 Hyundai Sonata and I’m have the same issue. P1326 and car went into limp mode. Changed knock sensor,new spark plus and new oil change. 700 miles later,P1326 again.
@yb2112
2 ай бұрын
should i just change the whole intake assembly ?
@ganeshkhatri8869
6 ай бұрын
can we get the arm attachment (white which is attached to the manifold) separately? what's the part name?
@joeydelmarsjr.646
9 ай бұрын
2017 kia optima replaced VCM aka Imrc after getting p200a but i get same CEL either solid or flashing and code came back. so now i dont know what do to
@kervenexantus5133
4 ай бұрын
I changed this part twice, got it from autozone with a yea warranty on it and it’s still showing the same code. can you please assist
@glennsmith8662
Жыл бұрын
Thanks!
@sansiro5538
Жыл бұрын
i have problem with camshaft and cranshaft i change every thing but have same problem . but i dnt change same thing in video pls help me
@stockyboys7231
Жыл бұрын
What’s bro what else can code p1326 be beside that part because I replaced that part and it’s still has acceleration problems
@dominiczido1572
Жыл бұрын
knock sensor
@karlitozdestroye
Жыл бұрын
Did you find what is your problem?
@migueljaden23
9 ай бұрын
Would this cause o1326 and car not accelerate
@manuelmaldonado6304
2 жыл бұрын
Do you happen to know the part number for just the VCM arm? My VCM arm has cracked in two so I need to replace it.
@joeb134
10 ай бұрын
If anyone is still looking for this it's in the VCM service kit. $13 at the dealership. It includes the bar, the clip, the white plastic piece with the nipple that connects to the motor and it's clip
@abelaguirre7725
9 ай бұрын
@joeb134 , thanks for the update definitely common it happened to me
@javierlares1669
Жыл бұрын
Did you erase the code or anything after replacing it? Or it just went off by itslef?
@DULLAHGOSOHARD
Жыл бұрын
Erase the code
@abelaguirre7725
Жыл бұрын
will this work for 2016 kia optima 2.4 ?
@jeffreyjones1801
Жыл бұрын
Should work.
@Peppermint1
Жыл бұрын
What exactly does fail ? I it inside the VCM unit or is it the small arm and knuckle wear ?
@DULLAHGOSOHARD
Жыл бұрын
Inside the vcm
@Peppermint1
Жыл бұрын
@@DULLAHGOSOHARD I want to open one and look inside, perhaps the plastic gears lack a bit of grease or the teeth just break. Perhaps stuck knuckles also cause too much force on these plastic gears
@DULLAHGOSOHARD
Жыл бұрын
Some time the fail is mechanical and some time it’s electrical but when you open it you might see it and other times you might not see anything
@Peppermint1
Жыл бұрын
@@DULLAHGOSOHARD Do you think it's risky to open it ? It is difficult to put the gears back in place ?
@DULLAHGOSOHARD
Жыл бұрын
@@Peppermint1 it look simple
@fernandoguardia-kd1wt
Жыл бұрын
Hi i have the same code but the mecanic erase the code and don’t chance the vcm if i change the vcm i need to do something in the obd scan?thanks i will apreciate the help
@DULLAHGOSOHARD
Жыл бұрын
You can change the parts and clear the code again and that should take care of it
@visualfan651
Жыл бұрын
I have replaced this part and the arm link kit. This has been about four times and every time I install a new arm link ,3 to 4 days after it snaps broken. Is there something that I have to do after do I have to relearn the car?
@DULLAHGOSOHARD
Жыл бұрын
Take off the intake and clean the runner flops that it control
@visualfan651
Жыл бұрын
@@DULLAHGOSOHARD would this be the same as me having the car on 2000rpm and taking off the brake booster hose and spraying brake cleaner ?
@lorenzohart9560
Жыл бұрын
You didnt have to reprogram it?
@DULLAHGOSOHARD
Жыл бұрын
No just clear the code
@lorenzohart9560
Жыл бұрын
@@DULLAHGOSOHARD preciate it
@karlitozdestroye
Жыл бұрын
I already change that part, and the motor is doing a ticking sound I need to clear the code again and will dissapear the sound?
@lorenzohart9560
Жыл бұрын
@@karlitozdestroye you might not have it going the right direction if that vcm motor is clicking. I ended up having to change the whole intake though because the runner in it was messed up. I did have to reprogram it for it to have full power.
@haydaralsultaniu2567
Жыл бұрын
ماهو الوظيفة هذا الجهاز
@douhghlie0444
Жыл бұрын
Dealer wants to charge me for two bucks/runner motor at $150 a piece for the part and $360 for labor. I belong 2016 Sonata SE only uses 1 bucks/runner motor
@lorenzohart9560
Жыл бұрын
They have a vcm actuator and a vcm position sensor on the 4cyl and v6. You sure thats not what they mean?
Пікірлер: 54