Lol I’ve seen 3 vids from this dude and he is working on his bike at night, reviving the hell out of that engine in each one of them lol. Neighbors must love you, man. Good vids though. I’m doing this swap on my ZX-6R soon and it looks a little more involved than my 300 was (pre Euro 5 emissions standards).
@adamstratford6740
3 жыл бұрын
Glad you went with the M4 Street Slayer as opposed to the M4GP imo looks way better 👌. I ran the GP on both my ZX6Rs few years ago and definitely prefer the Street Slayer Adam 🇬🇧
@khazzzzzz
3 жыл бұрын
I have the GP installed on my 2020. I like it better because it is short, and it is the best sounding exhaust for me.
@adamstratford6740
3 жыл бұрын
@@khazzzzzz hi buddy the Street Slayer is no longer in length than the GP or if it is it’s not really noticeable. As for sound the GP is a little deeper sounding imo but hey both sound and look great but for me if i was doing it all over again I’d definitely go with the Street Slayer. Adam 🇬🇧
@khazzzzzz
3 жыл бұрын
@@adamstratford6740 I agree. It's all personal preferences. Both slip-ons are great!
@adamstratford6740
3 жыл бұрын
@@khazzzzzz good talking to ya bro 👍🏻
@danrock54321
3 жыл бұрын
Yeah the M4GP ain't look as good as this one
@1983thunderbird
3 жыл бұрын
M4 with baffle in, sounds best to me!
@reroan2670
3 жыл бұрын
Baffle ouuuut.
@raikyjin4569
3 жыл бұрын
I cant wait for my m4 slayer to get here from usa im in nz love the content
@hakunamatata3118
3 жыл бұрын
can you make a video of your mods list so far that carbon took my attentiion
@Yessir-ed8do
Жыл бұрын
Baffle in sounds best Sounds smoother without rough idle
@cmbiker
Жыл бұрын
Thanks for your video of installing the A2 and this M4. Both are very helpful. I had a 2021 ZX6R with the A2 on it and loved the sound, but recently test rode a used 21 ZX6R with the M4 Street Slayer on it and really loved the sound. It sounded a bit louder and more gnarly, but I kind of loved it. I'm picking up a 23 ZX6R tomorrow and decided to order the M4 Street Slayer this time around. Quick question. I read some comments on KZitem from folk that said because the swingarm is made of aluminum and the M4 can is pushing heat out directly on it, that could soften up the swingarm over time and cause it to warp or even break. I know you are not an expert by any means on this topic, but just wondered what your 2 cents were, if any, on it?
@chadrichards8930
Жыл бұрын
Whoever said that about the heat and swingarm is an absolute idiot and stay as far away from them and any of their advice as possible
@johnb1797
3 жыл бұрын
I have enjoyed your easy step by step videos. I just received my street slayer and will be removing my stock exhaust. The installations that came with the slip on says I just need to remove the cables from the service motor and remove the old muffler and muffler box before installing. Is it really that easy? I saw in your yoshimura video that exhaust came with an attachment for the servo motor. Am I missing something, or need to purchase any additional parts.
@blainehouser4354
3 жыл бұрын
Bike Looks Awesome! I got the 2020 ZX6R KTR Version.
@jc_alpha
2 жыл бұрын
Oh man that sounds so sick! Does the heat/fumes from the exhaust not bother you or the passenger (for people who have passengers) being that the exhaust is so close to your feet and pointing in the direction of the passenger?
@eastcoastish
2 жыл бұрын
I haven't noticed any excessive heat or fumes. I don't really ever have passengers on this bike so not sure about a 2 up situation.
@joshb6469
3 жыл бұрын
My ZX6R had an M4 exhaust with no baffle when i bought it. Would you happen to know if i can buy any M4 baffle or does it have to be a specific one? It looks exactly like the one you installed in this video.
@eastcoastish
3 жыл бұрын
I'd just hit up M4, I'm sure they can sell you just the baffle.
@footballa57
9 ай бұрын
Looking back are you glad you switched? What are you currently using? Were you unhappy with the yoshimura? I have the same bike and am considering these same 2 exhausts.
@trese0000
3 жыл бұрын
Hey buddy, do you have plans on anymore update mods for the ZX6? Been some time since you uploaded for this series playlist. Looking forward to some fresh vids. Thanks 😊
@eastcoastish
3 жыл бұрын
I just put on the TST levers; I've got some more mods coming that I'll do once my bikes get down here in San Diego :)
@trese0000
3 жыл бұрын
@@eastcoastish I put those exact same shorty levers on mine. San Diego is not a bad destination to be waiting on them to arrive 😊.
@Azteca_016
3 жыл бұрын
Question: I know you said you like the bolt that comes with the bike. But due to the size of the hole in the street slayer, you weren’t able to fit it. Wouldn’t it had worked if you would’ve filed the hole a bit for fitment for the original hardware? Did that crossed your mind or were you worried it could cause some structural damage if you filed the hole? Thanks for feedback. I’ll be swapping my exhaust for a M4 as well.
@eastcoastish
3 жыл бұрын
Yeh filing or drilling out the hole would have allowed use of the stock bolt.
@Azteca_016
3 жыл бұрын
@@eastcoastish ok thanks. Unfortunately my ZX6R didn’t come with the stock exhaust system, which included an altered stock exhaust that ran a straight pipe that was welded at the base and no cat, so the bolt was gone. I also ran into the problem that the exhaust header gasket that came with it was bigger than the OEM gasket. I believe this was cause the pipe they welded was smaller in diameter to the original. I went all the way to Austin to go get the OEM gasket. So that should fix the problem. Thanks for your input sir.
@VicsVlogz
3 жыл бұрын
WOW. Can’t wait to get mine 😍😩
@michaelwright5856
2 жыл бұрын
In love with all the carbon on the bike. If you don't mind me asking, where did you get it from? I'm planning on getting a ZX6R in the spring time of 2022 so I'd love to know a good place to get carbon pieces for the bike thanks!!!!
@eastcoastish
2 жыл бұрын
Check out Z4-Motorsports on eBay.
@Isaiasmancilla-mc8pl
2 ай бұрын
I actually did the opposite. The street slayer was too loud and droned like crazy when I was commuting at 70 mph. Got the Yosh pipe and it was much better.
@Lucky_Logan
2 жыл бұрын
Dude do you live in Florida? Like around the east coast of Florida? Because that track day clip you put in looks exactly like Palm Beach International Raceway (PBIR), and that’s the closest track to me. I live in the Treasure Coast of Florida.
@eastcoastish
2 жыл бұрын
Yeh I was in Melbourne Florida and yes that was PBIR! However, I just moved to San Diego, CA so looking for tracks over here now...
@carlosfrances01
3 жыл бұрын
Did you delete the cat with the M4 ?
@tnamesneo9063
2 жыл бұрын
Man he said there was no sound difference, is he drugged or completely deaf? Jesus that m4 is eargasm I need one for my zx6r currently got a decat Leo Vince but it's just not enough for my liking😄
@eastcoastish
2 жыл бұрын
You can def here the difference when you play the clips side by side. In my echoing garage it was hard to notice a difference.
@Jayjayperalta1990
3 жыл бұрын
Do u have that breaking/crackling sound when ur off the throttle? I dont know to explain it lol..It just sounds weird to me.
@angelahayward4407
Жыл бұрын
The M4 sounds much cleaner and and clear than the Yosh
@shawnmacquillan8782
2 жыл бұрын
When you first added the slip on did you lose low end power?
@eastcoastish
2 жыл бұрын
No, I got my PCV re-tuned for this after I replaced the Yoshimura Alpha and I actually picked up 1-2hp across the RPM range.
@HemiBurns
2 жыл бұрын
M4 is fucking SICK sound.....
@M82Predator
3 жыл бұрын
Hey! I have stock exhaust on my 2021 ZX6R, if I were to get this M4, would I need the linkage pipe or anything like that. Or should be good to go from stock to the M4. Thanks!
@eastcoastish
3 жыл бұрын
The M4 goes straight into the factory headers so you should be good to go.
@fernandoreyes8400
3 жыл бұрын
Dude I had the same question! Thanks great video!
@M82Predator
3 жыл бұрын
@@fernandoreyes8400 I got it and it is great. I just had to remove the bigger exhaust part under, was fine.
@fernandoreyes8400
3 жыл бұрын
@@M82Predator did you remove that cat as well?
@M82Predator
3 жыл бұрын
@@fernandoreyes8400 I think so, was the bigger square shaped pan almost. Was heavier.
@topx2698
Жыл бұрын
what the decibel for yoshi and m4 please
@w.e.bdesigndetail5047
Жыл бұрын
How do you removed the insert
@curtisyoung4028
2 жыл бұрын
Where can I get the m4 from what website
@jc_alpha
2 жыл бұрын
I read somewhere that having the exhaust pointing to the swing arm like that is a bad idea because the heat may damage the swing arm. Have you heard anything like that anywhere?
@eastcoastish
2 жыл бұрын
If it's pointing straight at the swingarm I guess I could see it being a problem, but yeh this setup doesn't even get the swingarm warm.
@Christophershredz
2 жыл бұрын
Nothing is pointing directly at the swing arm
@Rizziculous
Жыл бұрын
I highly doubt any company would design an exhaust pointing towards the rear tire…
@jc_alpha
Жыл бұрын
@@Rizziculous not the tire… the swingarm. This exhaust pipe is right against it and I heard the heat is not good for it. Don’t know if it’s true though and that’s why I asked here.
@richardjones5632
3 жыл бұрын
I have a 2021 636 and I bought the same exhaust.. the m4 pipe diameter is measuring alittle of 2" but the other is measuring 2⅜. Could you tell me what the diameter is on your m4?
@eastcoastish
3 жыл бұрын
Putting calipers on it, the OD of the M4 pipe is 55mm.
@HOPPOVERSION1
3 жыл бұрын
fantastic buddy
@bryangutierrez4455
Жыл бұрын
What headers do you have on?
@adonisdario6182
3 жыл бұрын
where you buy those carbon fiber parts of it? thanks im planning to get that slip on.
@eastcoastish
3 жыл бұрын
Check out Z4 Motorsports on eBay
@lexthebarber9813
3 жыл бұрын
Does the m4 kit come with the same servo replacement as the yoshimura kit?
@eastcoastish
3 жыл бұрын
Nope, It only comes with the slip on.
@Keep_on_Dreaming
Жыл бұрын
I really want the 636 '19+ as my starter because they sound so good. Do you guys recommend getting it; it does have low power mode and 3 tcs.
@eastcoastish
Жыл бұрын
it's a pretty fast bike for a starter, i had a couple of bikes CBR500 and CBR650 before this...
@Keep_on_Dreaming
Жыл бұрын
@@eastcoastish What is a more beginner bike that has a quick shifter other than the zx-6r than?
@eastcoastish
Жыл бұрын
@@Keep_on_Dreaming quick shifters are neat but they’re not a big deal - it’s better to learn to ride well without one first anyway. Good starter bikes: Yamaha R3, Honda CBR500R and Kawasaki Ninja 400 in my opinion.
@Keep_on_Dreaming
Жыл бұрын
@@eastcoastish What about the cbr650r? and are the honda bikes as reliable as their cars?
@Traetz
2 жыл бұрын
Does it come with the mid pipe? Cause I still have stock everything on my bike and I'm wondering if I buy this will it come with the mid pipe
@eastcoastish
2 жыл бұрын
The pipe I bought did not come with the mid pipe.
@Christophershredz
2 жыл бұрын
This deletes the second muffler as well so it works like a mid pipe
@lucas.310
Жыл бұрын
Is a tune or flash needed after installing a slip on for zx6r?
@IWouldConclude
Жыл бұрын
Nope😊
@peters5903
2 жыл бұрын
m4 looks way better, yoshi sounds better imo it lsounds more refined...like crisp and clear, m4 sounds a little blurry like
@willterrell2748
3 жыл бұрын
Hey Kent. Nice video. Where'd you get that fresh hat?
@eastcoastish
3 жыл бұрын
Thanks man, got the hat from Tilly's.
@echo.motion
3 жыл бұрын
Did you sell the Yoshimura exhaust?
@eastcoastish
3 жыл бұрын
I just through it up on eBay: www.ebay.com/itm/203201913433
@robscherer
3 жыл бұрын
Still loving this thing? It is awesome haha
@eastcoastish
3 жыл бұрын
Yep, it's my go-to bike when I need to get somewhere fast :)
@robscherer
3 жыл бұрын
Kent, if you don't mind me asking lol, what do you do for a living?
@Jon-et3eo
3 жыл бұрын
Which exhaust is louder at idle, and open throttle... Yoshi or M4? It sounds like the M4 is louder even with the baffle insert than the Yoshi without insert. The M4 looks great.
@eastcoastish
3 жыл бұрын
M4 with the baffle is about the same as the Yoshi. The M4 without the baffle is louder at idle and throttle than the Yoshi.
@leestephen4288
3 жыл бұрын
Did u need a tune or anything with just changing the slip on ?
@ckeene2
3 жыл бұрын
Nope not with a slip on. You only need a tuner if you change the headers.
@aaronvassar7706
2 жыл бұрын
"Need", no. But the stock maps on these are garbage, so you should have it tuned anyway, whether stock/ slip-on, or full system.
@R1dermod
3 жыл бұрын
What bolts did you use after taking off the passenger foot pegs?
@eastcoastish
3 жыл бұрын
M8*12mm pan bolts. I got some fancy blue titanium ones, but that was just for the look.
@R1dermod
3 жыл бұрын
@@eastcoastish what site did you get the blue ones from?
Did you need to retune? What did you do with the servo?
@motion-tk4176
Жыл бұрын
i put a two brothers full system on my 2019 636 and i just took the servo out and installed a servo buddy (on amazon) so i didnt get a CEL!
@derickbalualua1921
Жыл бұрын
@@motion-tk4176 how is the bike running now with your current setup? Any plans in the future for a tune?
@GHOSTFACENINJA
3 жыл бұрын
Can you put the m4 exhaust link below?
@eastcoastish
3 жыл бұрын
I purchased mine from eBay seller "wickedracingstore"
@free82r
3 жыл бұрын
Hey man, I'm looking to get a m4 street slayer for my 21 zx6r, do I need to get a servo buddy or no?
@eastcoastish
3 жыл бұрын
Yes you'll need a servo buddy.
@meza5207
3 жыл бұрын
Get a m4 gp19 .. don’t need servo buddy if you keep the servo in but best to take out .. I’ll upload a video of how it sounds I got a full system tho
@meza5207
3 жыл бұрын
Get a m4 gp19 .. don’t need servo buddy if you keep the servo in but best to take out .. I’ll upload a video of how it sounds I got a full system tho
@Christophershredz
2 жыл бұрын
@@eastcoastish you actually don’t if you just pull the cables . It you delete the actual servo mechanism/box then you will just to clarify
@eastcoastish
2 жыл бұрын
@@Christophershredz If you remove the cables, you don't need a servo buddy or the fake-out mount that Yoshi provides in their kit?
@afro3manmoney741
3 жыл бұрын
Does that muffler burn your tire
@eastcoastish
3 жыл бұрын
No
@rolandbasergo6734
2 жыл бұрын
Hi, does that fit on a 2022? Thanks
@eastcoastish
2 жыл бұрын
I would confirm with the manufacturer, but I do not believe anything changed from the '19 to the '22.
@bassboostedmaster7953
2 жыл бұрын
Yes it does. I have it on my 2022
@aleksandarparipovic1450
9 ай бұрын
M4
@gamingradius8057
3 жыл бұрын
I actually find the sound quality a lot lower than the yoshi. But m4 looks better.
@HemiBurns
2 жыл бұрын
M4 wins in the setting car alarms off...so it wins.
@cmbiker
Жыл бұрын
@@HemiBurns 😂🤣😅
@warsok2151
3 жыл бұрын
Is your headers stock?
@eastcoastish
3 жыл бұрын
Yes, stock headers.
@bradenbarnes7800
3 жыл бұрын
Do I need to retune the bike with this exhaust
@eastcoastish
3 жыл бұрын
It depends on what your setup is. If you have a PC-V, it would probably help to have it retuned, but it's not necessary if you're only changing the exhaust.
@bradenbarnes7800
3 жыл бұрын
@@eastcoastish I have Yamaha R3 and I wanna get just the slip on is it necessary
@eastcoastish
3 жыл бұрын
@@bradenbarnes7800 If you're only adding a slip on, you'll be fine without a tune.
@williamdolezal9184
3 жыл бұрын
Does this delete the cat
@Lifeinthecountryfamilyislife
3 жыл бұрын
No just the res.
@garylee9240
3 жыл бұрын
I'll buy your Yoshimura if you still have it
@eastcoastish
3 жыл бұрын
on eBay: www.ebay.com/itm/203201913433
@DERMARCODEUTSCH
3 жыл бұрын
Does this m4 get in my Ninja 650 2019?
@eastcoastish
3 жыл бұрын
It’s a different model but they do make an M4 exhaust for the Ninja 650.
@paserpase2870
2 жыл бұрын
M4 slip on Sounds trash, you gotta do a full exhaust change this ain't working,
Пікірлер: 128