I'm dealing with an M80 that was leaking out the pitman arm side of the sector shaft; it was just pouring out. Off my 2001 Monaco Knight 36R motorhome. I tried to get the pitman arm off using a smaller puller and it just broke lol so I've ordered a big one like you used and will try again tomorrow. Thanks so much for the video!
@davehughesfarm7983
8 ай бұрын
I am tackling this project right now on My IH eagle...Very very similar except 4 bolts on a 9400...
@thehunteking
6 ай бұрын
I found one of these on a fire truck .. dust cover was leaking and didnt know any better. Couldn't get the pitman arm off had to pretty much hire someone to get damn thing off. Replace what I needed to get back in service and I'm paying for it today...gotta go back in and replace the rest. FML. But you give me ideas. 💪
@terrellscaife2411
3 жыл бұрын
Hey man nice work I recently did a steering box on a 1994 Lincoln town car so I can say your job was a little bit bigger than mine
@manuelcalderon3597
2 жыл бұрын
Donde puedo conseguir el extractor para sacar el brazo de la dirección
@davidkutz1051
8 ай бұрын
And now I know better… thank you!
@thehunteking
6 ай бұрын
You said you could do it on the truck? How you getting that last seal in with it on the truck? That's where mines leaking from. So I gotta go that deep.
@yeisonorozco6407
3 жыл бұрын
Hi very helpful video.. by any chance you know where I can order the replacement seals? I have a 1991 international 4900 dt 466 7.6 motor.?
@srandsonsrepair4685
3 жыл бұрын
Try mpparts.com
@technicalitems731
Жыл бұрын
What’s the proper way to fix the shaft where the seal has made a groove? If you use a lathe…..how do you take up the slack? I have found these seal kits on eBay. I need to do my 1997 Mack ch613 dump truck. Sheppard m100. Leaking on inner side by frame rail. A shop on atlanta quoted me $550 to do a rebuild and reseal on whole unit. A local parts dealer said they could get me an m100 for my Mack out of Orlando for $1200. October 2022. Unit weighs 90 plus pounds.
@crenninger1000
Жыл бұрын
i had a machine shop spray weld the shaft to build up the wear groove. there is a seal on the inside of the box near the frame that i replaced without removing the box. pull arm off and then remove the shaft ,install new seal on inside and reinstall parts,was not that hard
@davehughesfarm7983
8 ай бұрын
Ridiculous aint it? Thats why I am doing it my self..
@mercades0
7 ай бұрын
Are you still rebuilding steering gear boxes ?
@cranerigging3604
2 жыл бұрын
Nice work ! I need to replace the steering shaft seal on one in the morning . Any part numbers or places you recommend to get the seals ?
@srandsonsrepair4685
2 жыл бұрын
I ordered seal kit from mp parts, it covered several models.
@cranerigging3604
2 жыл бұрын
@@srandsonsrepair4685 Thank you and will do !
@cranerigging3604
2 жыл бұрын
@@srandsonsrepair4685 We ended up calling the International dealer and they had the seal kit in stock . Went back together fine and no more leaks . Thanks again !
@srandsonsrepair4685
2 жыл бұрын
@@cranerigging3604 excellent
@gary6357
Жыл бұрын
I was wondering if you had the part number for the Mp parts I have the identical gear box leaking and the international part number I give them isn’t cross referencing
@srandsonsrepair4685
Жыл бұрын
Seal kit for a sheppard m100 is what i used, they’re available on ebay as well
@melgar484
4 жыл бұрын
Nice video, I was wondering if you can tell me where did you get that puller? Thank you
@srandsonsrepair4685
4 жыл бұрын
Otc 4534 puller set
@melgar484
4 жыл бұрын
sr and sons repair , thank you very much
@luisaucu7688
2 жыл бұрын
Excelente
@user-jr8lf6pl2m
3 жыл бұрын
Hi! Thanks for video! What kinde of engine on this dump truck?
@srandsonsrepair4685
3 жыл бұрын
L10 cummins
@rodrigoperez-jn7rg
4 жыл бұрын
Where did you buy the kit? My international dealer said those seals were not available
@srandsonsrepair4685
4 жыл бұрын
I ordered kit from mpparts
@carytowncat
3 жыл бұрын
Have same exact seal leak on 93 International. M100.
Пікірлер: 30