Preventive Maintenance > Maintenance ☆OBDEleven: obdeleven.com/?aff=1175& ☆For a 10% DISCOUNT on ANYTHING, type in NEED4BUILT10 in the add discount code section!
@liamcole6586
Жыл бұрын
Just had my brake booster go out in my 2018 b9 s4 but never experienced anything else and almost at 60k miles. About to go stage 1 finally but waiting for Audi to get this part. Haven't had the issue with the PCV value but now im considering doing it.
What PCV did you use ? Can you please let me know I need one .
@Need4Built
9 ай бұрын
@@CHRISCAPO9 please check the description. Oem pcv.
@________________7279
Жыл бұрын
Bout my S5 b9 at 5 miles and had to replace this particular part at 70k. Started leaking oil and lose power - - seems like a major issue for many in the Audi line up. Thanks for posting!
@Need4Built
Жыл бұрын
Get her changed out! Thanks for the support!
@Corbots80
6 ай бұрын
It sucks that you were not aware. Put the PCV is a maintenance item on this engine. Thank fully it's easy to get to and replace as a DIY
@thebobb8654
Жыл бұрын
funny have same car and the PCV just went bad yesterday. thx for the video.
@Need4Built
Жыл бұрын
Get that bad boi replaced! You’re welcome! 🤝
@stefanomarcellino6701
Жыл бұрын
How many miles do you have
@Need4Built
Жыл бұрын
@@stefanomarcellino6701 My sq5 pcv failed at 55k miles. This S5’s pcv failed at approx 60k miles.
@thebobb8654
Жыл бұрын
@@stefanomarcellino6701 53k
@blade643
Жыл бұрын
Good to know how easy of a job this is, thanks bro
@benjiiponomrenko7046
Жыл бұрын
Bro that’s crazy 🔥 love the s5 and sq5
@Need4Built
Жыл бұрын
Both are torque monsters! 🚀
@Corbots80
6 ай бұрын
Glad to see it is such an easier replacement vs the B8
@Need4Built
6 ай бұрын
I know right! B8 is a bust.
@Corbots80
6 ай бұрын
@@Need4Built I can't afford it just yet. But I'm excited to upgrade to a B9
@flipboi952
Жыл бұрын
Good to know info. Looking to get a sq5 after selling my b9 s4 two years ago.
@Need4Built
Жыл бұрын
Excited to see you make that happen man! SQ5’s are the move!
@fredzimmer8626
Жыл бұрын
Well it looks like moving to the B9 doesn't end dealing with PCV issues but it definitely appears to be a much easier job so that's a big plus.
@Need4Built
Жыл бұрын
Much easier than removing the supercharger like on the B8/B8.5! There’s still one hose under the turbo, but it’s a very rare failure and can easily be replaced when going stage 3🚀
@fredzimmer8626
Жыл бұрын
@@Need4Built I have to also say for me the B9 S4/S5 exterior is not even close to the B8.5 look. Interior win goes to the B9 hands down. The B8.5 SQ5 exterior vs the B9 SQ5 is a tie for me at this point. I think the B8.5 S4 is going to be one of those timeless looks that just gets better with age. (my unsolicited opinion) 😬
@Need4Built
Жыл бұрын
@@fredzimmer8626 I cannot argue with you on the B8.5 S4 being a timeless perfect example. I believe it’s going to turn into a collectors car similar to the B5 S4. The b9 interior is awesome and all but I would totally swap the interior into a b8.5 and keep the body/chassis. Maybe I’ll buy a B8.5 S4 for my little guy one day and build it with him! BUT I think the B9 SQ5 inside/out is a huge difference and improvement over the b8.5 S4, not even talking about the motor, just looks. Come through, I’ll give you a ride in mine. Change your mind 😉
@uncensored6420
Жыл бұрын
Hey easy now. We love and appreciate all Audi's interior and exterior 😁
@Need4Built
Жыл бұрын
@@uncensored6420 I couldn’t agree more 👏🏼
@davejones3434
Жыл бұрын
Hey guys great video. For future reference those triple socket thingys you refer to are called Torx bits. Party on.
@bokiNYC
10 ай бұрын
Or tripple square?
@me5ponk454
Жыл бұрын
How is replacing the PCV restoring any lost horsepower?
@lukaweixler
Жыл бұрын
Brooo I love your channel!! I love Audis😊
@Need4Built
Жыл бұрын
Really happy you found me ! Stay tuned for more!
@lukaweixler
Жыл бұрын
@@Need4Built thank you 😁
@Mr.El_Guapo
11 ай бұрын
The part that fails on the B9 is the Y pipe that unfortunately comes with the turbo inlet, Not the PCV itself. (The really most common atleast, my B9 S4 included). Easier job to to and cheaper too.
@Need4Built
11 ай бұрын
The pcv check valve and gasket have failed on me and many other owners. It’s smart to replace the Y pipe and the pcv itself.
@Mr.El_Guapo
11 ай бұрын
@@Need4Built Yes, I forgot to say your case was probably different. I mean you woulda known if it still leaked after😅 Didn’t mean it in a mean way, just trying to spread infos that were hidden from me on the pages when I got the car last year and it started leaking from the oil cap. Oil would end up in the intake from the check valve failing making my car smoking a lil bit and loose a little bit of power
@lono9885able
Жыл бұрын
This is aspirational for my B9 SQ5 that I love even stock. No one is tuning them like this in the UK. I can't find the answer anywhere but do you know what the standard engine internals are rated to in terms of power? And the ZF in terms of torque?
@Need4Built
Жыл бұрын
I hope to see you build yours! The B9 3.0t rods are rated for 600wtq at a safe limit. I’m making 620wtq/640whp without any issues for 10k miles already. The zf8 transmission, 8hp55 is is rated for upwards of 800wtq I believe. It’s insane. The trans is more bullet proof than the engine. We have seen a few people make 700whp/700wtq without issues but that’s kind of a huge danger zone. The power I’m at right now is right there at the safe limit.
@Kiss__Kiss
Жыл бұрын
What's interesting about this replacement/install, is that the part being removed is 06M 103 A01.. The new(replacement) part @3:23 is also 06M 103 A01 (You can again, see the "replaced" part number @ 6:02 ) ... Yet, in the video description, it reads, For parts needed : PARTS NEEDED: Oil Separator: 06M-103-515-H
@Need4Built
Жыл бұрын
What’s interesting is that you’re behind on the updated part numbers. It’s the same part. 06M-103-515-H is the updated part number and the suppression is 06M 103 A01 parts.audiusa.com/p/Audi__/Engine-Crankcase-Vent-Valve-Engine-Oil-Filler-Tube-Engine-Oil-Separator-Filter/70048001/06M103515H.html If you search up 06M 103 A01, it will pop up as 06M-103-515-H due to it being updated. You stand corrected sir.
@antonioennis1448
Жыл бұрын
With VWAG parts, the numbers and or letters at the end are a revision or variation.
@juniormeyer27
Жыл бұрын
The videos are great, it’s great to see German car enthusiast who actually know what they are talking about. I would also suggest looking in to updated versions of the diverter valve if available or replacing if an older vehicle and or tuned. All good sound information and great execution.
@tombrown9246
Жыл бұрын
Great vid man
@Need4Built
Жыл бұрын
Thank you! 📈
@muzikking
Жыл бұрын
Great video! Keep them coming
@Need4Built
Жыл бұрын
You betcha! Lots more in the works 📈
@petejr7583
Жыл бұрын
2 words: laser lights😉. They are good! Btw, I have the ‘21 Ascari Launch Edition and love it!
@Need4Built
11 ай бұрын
Sick!
@BocaAtractivo82
4 ай бұрын
This is a great save DIY when my CPO warranty expires :) Quick question though, 024 have an expensive oil catch can system that replaces the plastic PVC to a metal unit. What are your thoughts on that? Just curious that you don't have it w/your SQ5. Is it because it have limitations due to the high boost? Would you recommend it? Or an entirely different aftermarket product?
@Need4Built
3 ай бұрын
Wait for 034’s catch can.
@BocaAtractivo82
3 ай бұрын
@@Need4Built Sounds good.Thank You
@sebastiantu6212
Жыл бұрын
I'm now confused as to which of the three parts fail. 034 seems to only specify the host part you've replaced as being the issue (with its check value). You show the PCV itself being replaced for its gasket (this fails as a result of the check valve failing right? As only then does the pressure burst it). The other hose that goes under the turbo is also a PCV hose, but is this involved in any of the failures? I assume not as you didn't replace it
@Need4Built
Жыл бұрын
Replace them both. Pcv and hose. Don’t worry about the hose under the turbo just do it when you go stage 3.
@nasa_unofficial723
4 ай бұрын
What are your thoughts on the racingline PCV replacement for this vehicle the only downside I think is it’s not rated for over 30psi… 034 motorsports stg 1 has boost of 22-25… worth it or no?
@Need4Built
3 ай бұрын
Waste of money. Wait for 034’s catch can to come out.
@HeavyOnCars
Жыл бұрын
Hi Dude, my S5 B9 Sportback has thrown P2279 and P0507 error codes and I am here in the UK watching your video 1am on a Saturday. Glad to see that it does not look that expensive to fix. Can't believe the PCV valve failure is such a common failure and that Audi hasn't recalled for free replacement. Are there any stronger aftermarket parts that you would recommend? Or shall I just go with Audi OEM and hope that lightning doesn't strike twice?
@Need4Built
Жыл бұрын
034 Motorsport is working on an upgraded option. However at this moment it’s fairly cheap to just replace it with a stock option since it’s quite cheap.
@HeavyOnCars
Жыл бұрын
@@Need4Built yeah you are right. OEM is inexpensive so will stick with that for now thanks.
@giovannimalek9211
Жыл бұрын
Would you be able to link where you purchased it from? Great video btw
@giovannimalek9211
Жыл бұрын
I think mine may be bad because when accelerating I hear a high pitched whistling noise, almost sounds like a supercharger, I’ve heard some people say it’s the ZF8 transmission but this seems more likely
@Need4Built
Жыл бұрын
parts.audiusa.com All oem parts from Audi. You can also see if your local dealership would be cheaper. The part numbers are all listed in the description so check it out! You should look under the hood and see if you can see any oil. This s5 owner also told me the same thing: whistling noises when accelerating. Possibly just vacuum leaking. Zf8 definitely has nothing to do with such sounds.
@giovannimalek9211
Жыл бұрын
@@Need4Built thank you I appreciate that!
@giovannimalek9211
Жыл бұрын
@@Need4Built what part do I lookup on the website. Like what’s it called specifically?
@Need4Built
Жыл бұрын
@@giovannimalek9211 PARTS NEEDED: Oil Separator: 06M-103-515-H Separator Gasket: 06M-103-517-B Oil filter Gasket: 06M-103-727-A Intake Manifold Hose: 06M-129-041-H Positive Crankcase Hose: 06M-103-217-DD (optional, under the turbo) Just look up the part numbers and they will come up directly!
@arif7479
10 ай бұрын
Just got a used b9 s5 with 18k miles. The dealer was sketchy he sold me the car without changing oil and he reset the oil thing so I wouldn’t know. What are some other things thats I should check or replace or look out for this is my first car. Thank you. I also paid 3300 for a 3 yr warranty is that worth it?
@Need4Built
9 ай бұрын
Take it to an Audi/VW third party shop to get inspected if you dont trust the dealer.
@KE0PS77
5 ай бұрын
Hey guys just found out this channel (I really liked btw), question here : -Any issues with the infamous rocker arms? I own an S5 sportback mid 2018, with currently 68k and lost my warranty recently, I'm really hesitating keeping the car because of it... Any advice will do!
@CT_216
3 ай бұрын
Any idea what rear diffuser is on the car? Great video!
@Need4Built
3 ай бұрын
No idea but thank you for watching
@BI4ckdragon
Ай бұрын
@@Need4Built maxton design rear diffusor
@browncowsoftware
Жыл бұрын
that crash bar looks like mine. I had mine powder coated black, but over time it has been getting chipped or flaked away. Mine looks identical. I'm gonna try to spray paint a few coats next time.
@Need4Built
Жыл бұрын
I had the same issue with my B8.5 S4 crash bar and my B9 SQ5 crash bar. One of my buddies recommended instead of regular spray paint or powder coat to use high quality black truck bed linear you can find at your local auto parts store. Apparently its ALOT more durable and will not get chipped or ruined over time. He’s had it on his crash bar for over 10k miles, no chips. I’m doing it next on my SQ5.
@chriss4739
Жыл бұрын
Use 3M rubberized truck bed liner. Scuff it up and clean well before spraying
@Need4Built
Жыл бұрын
@@chriss4739 thanks for the tip!
@mchong91
Жыл бұрын
Do you think black duct tape would work?
@Need4Built
Жыл бұрын
@@mchong91 I think you would see it through the grille. Would be pretty ugly I’m not going to lie.
@RandyRandy-s8n
8 ай бұрын
Great video! Can I remove my oil filter canister on my B9 3.0 to change the gasket without removing the turbo?
@Need4Built
8 ай бұрын
Yes absolutely. Would require putting car into service mode for easy access.
@RandyRandy-s8n
8 ай бұрын
@@Need4Built Ok going to try it tomorrow. Thanks!
@matthewfoster9755
7 ай бұрын
Hi from the uk . Great video . Useful information. Have you guys had any issues with rocket arm failures ?
@Need4Built
7 ай бұрын
None of my cars or No one I know has had this failure. It seems to be 1% of all B9’s on the road have suffered this. It’s an over exaggerated failure that’s insanely rare.
@matthewfoster9755
7 ай бұрын
@@Need4Built VAG technic over here have repaired many of these , with an in depth analysis of the issue . The rockers in question are very poorly made and designed . Audi no longer stock the part and only sell the new designed part . Their advice is to have the issue rectified if you going to tune the vehicle . As running it harder could cause catastrophic damage .
@Need4Built
7 ай бұрын
@@matthewfoster9755 Interesting. I can buy the new rockers anywhere in North America. Only the 2018-2019 vehicles have this issue. No running it hardware doesn’t accelerate the issue. Both stock and tuned b9’s have had the failure. VAG technic has fixed what maybe 20-30 b9’s with the failure? Out of HOW many b9’s in the UK? Thousands upon thousands? Again Audi has stated these rockers have had 1% of failure rate across all b9’s in the USA and europe. That’s a tiny ass number. There’s as much piston failures almost as rocker arm failure. Private Audi shops and even Audi techs have recommended simply going to 5w-40 could help the issue however if they fail, they fail. Oh well. It’s not that big of a deal.
@matthewfoster9755
7 ай бұрын
@@Need4Built I am torn as to changing the oil to 5w40 . What are you guys running ?
@Need4Built
7 ай бұрын
@@matthewfoster9755 I’m running 5w-40 in my b9’s and every b9 I touch
@darrinscoilsclouds1498
11 ай бұрын
Y not delete the pcv all together? That’s what I wanna do to mine. But it seems like everyone replaces them instead. I am wondering if there’s a good reason for this?
@Need4Built
8 ай бұрын
Can’t do a pcv delete lol. The entire engine and other systems are all vaccum dependent as well. There needs to be circulation. 034 is working on a solid proper check valve system with a catch can and billet pcv replacement. Wait for that.
@darrinscoilsclouds1498
8 ай бұрын
@@Need4Built i meen delet it from the intake to a check valevd with catch can.
@tsifty1
Жыл бұрын
Curious question, did it make you lose oil quicker then the usual Audi oil consumption?
@Need4Built
Жыл бұрын
Maybe a little bit, considering it was starting to leak outside the pcv. But In theory yes, a bad pcv does cause the engine to eat more oil.
@220g
Жыл бұрын
I thought the breather hose was the most common pcv part to fail? Great content
@Need4Built
Жыл бұрын
Both the hose and the check valve within the pcv fail unfortunately. Thank you!
@220g
Жыл бұрын
@@Need4Built Will be installing new breather hose this coming week, was told to order only that one first because it’s most likely the bad part.
@Need4Built
Жыл бұрын
@@220g Here is another great video that will change your mind. I highly recommend changing the pcv itself as well. kzitem.info/news/bejne/1pdttX9opZtog6A
@Magmaplayss
5 ай бұрын
Do you think this can cause an evap?
@Need4Built
4 ай бұрын
No. evap is fuel system related. There a sensor next to the turbo on the passenger side that goes bad and causes an evap code.
@zionrion5651
7 ай бұрын
Pcv change is insane
@Need4Built
7 ай бұрын
Not sure if this is sarcasm or not 🤣
@humanresources2138
6 ай бұрын
How do you find out that the torque spec was 10NM?
@Need4Built
6 ай бұрын
ALLDATA.
@livelifeyoung1996
9 ай бұрын
Did you guys only replace the PCV and that one? U didn’t do the sec hose right the one that’s hard to get to
@Need4Built
9 ай бұрын
Yes that’s under the turbo.
@Blank2SS
6 ай бұрын
Right now I have a camaro 2ss but I want an s5 or tts or s3 idk why bro
@Need4Built
6 ай бұрын
S5 would be the way to go my man. You can’t go wrong with that decision.
@Adubs808
Жыл бұрын
Help- where is the n80 valve in the s5 b9? I cant locate it :(
@Need4Built
Жыл бұрын
On the left side by the Hpfp.
@adamone90
Жыл бұрын
how did u get the mmi to look like that in the dash with the circle guage?
@Need4Built
Жыл бұрын
If you're talking about my SQ5, OBDELEVEN is really cool. Check it out!
@IainB
Жыл бұрын
Thanks for the PCV replacement walkthrough! Going under a car only held up by a single jackstand and a floor jack though? That's sketchy AF dude. At least slide a spare wheel under the frame.
@Need4Built
Жыл бұрын
I knew someone was gonna call me out, and you’re ABSOLUTELY correct it was sketch. We were in such a hurry to finish up the car, spaced about a secondary jack stand on the other side. I’ve never worked on something so dangerous. Lesson learned, the extra minute might save your life.
@ericjensen6993
Жыл бұрын
Hey what grill he he running on the s5 where did you guys buy it from looks good
@Need4Built
Жыл бұрын
I think it’s from canautoperformance. Check them out
@ferpi30
Ай бұрын
I'm going to do it myself. Stupid question, is it necessary to put the lucas heavy duty on? Because I don't have it in my country.
@Need4Built
15 күн бұрын
DIY all the way
@ferpi30
14 күн бұрын
@@Need4Built ✌🏻 i do it! Thanks bro. Here a follower for South America 🫡
@Madeiniran420
Жыл бұрын
Hi , would H&R Super Sport Spring Set with 2" lowering be perfect for my 2022 Audi Q5 45 Sline?
@Need4Built
Жыл бұрын
Yeah! Get that suv dropped
@Nikolee
6 ай бұрын
Where did you get your PCV from? Maybe I missed that part
@Need4Built
6 ай бұрын
directly from audi
@humanresources2138
6 ай бұрын
When I ordered the PCV hose it also came with the black tube that connects with the turbo. Do you know the torque spec for the 2 bolts?
@Need4Built
6 ай бұрын
10-12 NM. It’s basically hand tight.
@humanresources2138
6 ай бұрын
@@Need4BuiltIs there a secret to removing the hose. The connectors seem like they're locked in there.
@Need4Built
6 ай бұрын
@@humanresources2138 gotta press on both sides of it where there are two little marks on the hose and then get underneath it and it will “unlock” and pop out. Really dumb design and the worst connection Audi/VW ever created.
@mchong91
Жыл бұрын
Which brand of honeycomb grill is this? From what website? Thanks!
@Need4Built
Жыл бұрын
I believe it was from CanAutoPerformance!
@jimmychoi9900
Жыл бұрын
Why didn’t you paint or wrap the crash car to black? I’m installing my honeycomb grill soon and thinking how I’m going to blacked out the crash bar
@Need4Built
Жыл бұрын
You should absolutely do that. I’m not sure why the owner hasn’t done it but he should. All my cars were always blacked out.
@jimmychoi9900
Жыл бұрын
@@Need4Built yeah! I love your contents
@Need4Built
Жыл бұрын
@@jimmychoi9900 thank you! I’ll keep it up with more content then 💪🏼
@jimmychoi9900
Жыл бұрын
@@Need4Built quick question! What tools do I need to install the transmission mount? I want to install mine soon. Thanks and was it noticeable when you shift the gear?
@Need4Built
Жыл бұрын
@@jimmychoi9900 I would say your regular tool set+Triple square set should be able to do so. I think you might have to get a jack and support the transmission however also.
@ericmejia8634
Жыл бұрын
My 18 S5 sportback is giving me code P2227 any help fellas??? Appreciate it. 42k on the dash gave me driveability warning lights check engine and reduced acceleration. Would greatly appreciate any help! Just got it from Cali a week ago from the Porsche down there, they dont wanna take accountability for it.
@Need4Built
Жыл бұрын
Here's a good thread for you to read. www.audizine.com/forum/showthread.php/937555-P2227-and-P0236-(SOLVED)
@ericmejia8634
Жыл бұрын
@@Need4Built Appreciate you bro!
@ericmejia8634
Жыл бұрын
@@Need4Built The dealership told me they dont cover if its the ECM 😒😒 It falls under their 10 year 120k emissions warranty.
@awongvisuals
Жыл бұрын
Working on the car with a white shirt is crazy. Great video tho! lol
@Need4Built
Жыл бұрын
Thanks for the comment! I have some dedicated white work shirts 🫡
@pedromateo2760
8 ай бұрын
Is that transmission mount available for 2015 Q3
@Need4Built
8 ай бұрын
Maybe? See if 034 has it.
@vivanbhathena999
Жыл бұрын
pls send the link of the pcv details page
@Need4Built
Жыл бұрын
Please check description
@jimmychoi9900
Жыл бұрын
Would the transmission mount void my warranty?
@Need4Built
Жыл бұрын
Highly doubt that. Only an ecu tune. Even then the dealer would have to prove that the car is tuned.
@advocado7373
Жыл бұрын
He needs to fix that crush bar lol.
@Need4Built
Жыл бұрын
I’ll make him do it when he upgrades the IC.
@dimetime0
Жыл бұрын
What's the front splitter on the s5?
@Need4Built
Жыл бұрын
maxtondesignusa.net/products/front-splitter-v-2-audi-s5-a5-s-line-f5-coupe-sportback Here you go.
@pgmallon
Жыл бұрын
You want something that looks like a tesla? They may be alot of things, but good looking isn't one of them
@Need4Built
Жыл бұрын
Speaking facts. Don’t even start with the interior build quality 🤣
@pgmallon
Жыл бұрын
@@Need4Built I have seen the horror stories. Lol
@Corbots80
6 ай бұрын
LoL clueless
@pgmallon
6 ай бұрын
@@Corbots80 Please, go on...
@smoked.s3
Жыл бұрын
love the reactions!🤣🤙🏽
@_Imlazy
9 ай бұрын
😂 the BMW rear plate on the b9 😂😂😂😂
@Need4Built
8 ай бұрын
It’s wild. 😂 Ben is still a BMW guy at heart it seems.
@hjaniel4428
Жыл бұрын
👍
@Need4Built
Жыл бұрын
Thank you!
@grenalis
2 ай бұрын
13mm is 1/2in not 3/8in
@henrycervantezzz5566
Жыл бұрын
Launching at a light with school busses. Brilliant. Otherwise, good video.
@Need4Built
Жыл бұрын
🥲I wasn’t the driver. Mexico roads. Thank you so much for the kind words!
@adrianp9283
Жыл бұрын
All that work just to hit Tesla performance
@Need4Built
Жыл бұрын
L
@carramrod8232
Жыл бұрын
Teslas are boring cars. Nothing better than hearing that tuned 3.0 pop and crackle.
@restive3222
3 ай бұрын
What is that part? My English is not so good thanks for help
@Need4Built
3 ай бұрын
PCV. Positive crankcase ventilation
@amedaius8492
8 ай бұрын
Need to repaint that crash bar. Or maybe wrap it.
@Need4Built
8 ай бұрын
He wrapped it I think? Black truck bed liner works much better as well.
@amedaius8492
8 ай бұрын
@@Need4Built I had mine painted professionally when I did my grille swap, glad I went that route even though it was a little more. I've heard truck liner works well too.
@_allthingsdude
8 ай бұрын
5:53 😂😂😂😂
@Need4Built
8 ай бұрын
Solid edit
@timothyfogarty9007
Жыл бұрын
I’ve had a Jetta and nobody mistakes my S4 for a Jetta. I don’t hate the S5 I just prefer the slender look of the S4
@Need4Built
Жыл бұрын
It was absolutely a joke. I want an S4 myself.
@ucisigma
Жыл бұрын
Nice video. About to replace my PCV with racingline’s newly released PCV/Catch Can. Looks to be a solid replacement for the faulty stock
@Need4Built
Жыл бұрын
I agree! It’s definitely one hefty price tag, but the quality is there, and on the bright side you’ll never have to worry about the pcv again. 👏🏼
@4RingsJamz
Жыл бұрын
Can you run that set up on upgrades turbo i see that it’s not made for cars running then 2 barr
@ucisigma
Жыл бұрын
@@4RingsJamz idk. I’m only running 034s Stage 1 and have no issues with it. If you ask Racingline, please report back
Пікірлер: 184