Check out the full guide on howchoo for a text and photo version of this build! howchoo.com/g/zjm4zwzjzgi/pi-retrobox-build-your-own-diy-raspberry-pi-arcade-joystick
@n0anime342
6 жыл бұрын
No joke I'm building this right now
@matthewhibner1092
6 жыл бұрын
Hopefully your joystick isn't mounted crooked and your vents don't look a dog chewed on it like his. A little care goes a long way. Good luck and happy gaming Boss
@darken3150
4 жыл бұрын
Did you complete it?
@edwardwalsh9558
4 жыл бұрын
Flame polishing the edge of the acrylic would be a nice touch, its pretty simple and looks amazing.
@walterbkeen
6 жыл бұрын
FYI, You can clean up your edges by sanding with 220 grit sandpaper, and using a butane torch for a finished polish. Takes some practice, but the results are well worth the effort.
@Spiritual_Architect
5 жыл бұрын
Thank you. You wouldn't believe how many bad videos of this kind of build i had to watch before i finally found this one.
@uneCENT
6 жыл бұрын
Great video, thanks for showing us step by step and just how simple it can be to produce something so nice.
@Howchoo
6 жыл бұрын
Glad you enjoyed it! :)
@radkat7392
5 жыл бұрын
Thank you so much for the info about the additional controllers at 0:36. No other "KZitemr" answered this for me, and here you are first 30 seconds with an answer. Subbed 👍
@Howchoo
5 жыл бұрын
No problem! :)
@leemarson7350
5 жыл бұрын
Interesting project. Love retro gaming! I have no experience with Raspberry Pi's and would love build something. I have been looking at a few videos lately on how to make a bartop arcade. Hopefully one day I will get the chance. Thank you for taking the time to make the video!
@jdell6250
3 жыл бұрын
Your wet package on your porch came from the US Post Office (25 years with UPS). Thanks for a good guide for reference.
@Howchoo
3 жыл бұрын
Lol thanks for the insight! I believe you are correct.
@finnyabsley5685
4 жыл бұрын
Really happy this came up in recommended just finished setting up retro pie today 🙂
@MrWerepop
4 жыл бұрын
This was the videos I was looking for !!! Thanks Man
@Howchoo
4 жыл бұрын
No problem! Enjoy
@kevinbarton9052
6 жыл бұрын
That's great, lad. That is what I want playing all MAME arcade games only.
@SinX4Lyfe
5 жыл бұрын
Just bought all everything on the list to make this even the band saw. Bought some extra part just in case I fail! Wish me luck, I invested in this cost me 350$ for everything... planning to make a few once I become succesful to make for the family :)
@Howchoo
5 жыл бұрын
Awesome! You’re going to have a blast. If you run into any issues, feel free to post in the guide comments section or PM me and I’ll help you out. I monitor all the comments on howchoo so I’ll see it right away. :)
@edmund8954
5 жыл бұрын
how u do
@JuneLake158
5 жыл бұрын
Ahahahahaha, I’m building this, great vid. Shout out to Patrick. He lost. lol, I don’t know why that made me laugh.
@MikeysLab
6 жыл бұрын
Love the portable idea, I literally built this into an ikea table. One piece of advice add a laptop HD for much more storage, and a lipo for portable power haven’t played with a pi on my channel in a while, maybe time for a revisit
@TheEricclayton
7 жыл бұрын
Awesome video! Thanks for taking the time to make it. Gonna build one in the next few days
@Howchoo
7 жыл бұрын
No problem! :) Excited to see how your build turns out!
@MrLosttheplot
5 жыл бұрын
thanks for a great video, i built my own today, worked first time.
@Howchoo
5 жыл бұрын
Awesome! Glad it worked out well for you
@AndyMac40K
4 жыл бұрын
Quarantine project
@brianpdalton
6 жыл бұрын
This is great. Was this done with no soldering? EDIT: Yes it was.
@Minitaur89
5 жыл бұрын
Cool video inspiring me to make my own Arcade joystick :D
@Masterchief0521
6 жыл бұрын
my abs box finally came in, so next time I have a few days off I'm going to put it together!
@CCMAC0427
7 жыл бұрын
Thank you. I have been wanting to build something like this for a while but was stuck on how to get an enclosure. I do wish though you showed cutting the holes for it. That's the one place I am a little worried I'm gonna mess up and have to start over.
@ChamberlainCody
6 жыл бұрын
Definitely need more subs man I'm gonna share this stuff around
@massv953
7 жыл бұрын
Why not make the board comfortable/bigger though? Your joystick is too close to the buttons and there is no real estate there for palm rest, thats going to make extended fighter game play really uncomfortable. Control boxes are bigger for a reason.
@Howchoo
7 жыл бұрын
You can definitely make it bigger if you'd like -- same guide/process, just use a different project enclosure ;) I opted for this size because it's more portable and compact. It shares the same button layout/spacing as the Pimoroni PiCade, if you're familiar with that.
@Agamemnon2
6 жыл бұрын
Yeah, a bigger box would be more ergonomical. Plus you could add things like an amplifier and speakers in the extra internal space. Or just a stash for some candy.
@megido878
5 жыл бұрын
It's free real estate
@depopa1033
5 жыл бұрын
definitely building this some day.
@yahyalaouici9749
5 жыл бұрын
greetings from Algeria bro ur channel is a treasure,u have a new subscriber
@Howchoo
5 жыл бұрын
Thanks dude! Can’t wait to bring you more
@calebcook7324
7 жыл бұрын
600th subscriber ;) hope you guys grow more, great videos! keep it up
@Howchoo
7 жыл бұрын
Thanks Caleb! It means a lot. We're working on increasing video/guide frequency so we can share more with you!
@Fireblazer41
6 жыл бұрын
Can you show how you set up the controller on retropie? (As in what each button was mapped to)
@AndyCinDallas
6 жыл бұрын
I'm struggling with that part myself.
@railrenegade3040
6 жыл бұрын
Once you boot into the Emulation Station and choose controller setup, it will step you through programming buttons. You basically hit the corresponding button or move the controller direction according to what button you are programming.
@LAvocat
6 жыл бұрын
Nice video, and your voice is amazing, thanks for the tutorial !
@Howchoo
6 жыл бұрын
Why thank you! :)
@benbenben94
7 жыл бұрын
the "go ahead and..." guide to building a Retrobox
@chriscappello8240
7 жыл бұрын
Can you include direct links to the exact parts?
@Howchoo
7 жыл бұрын
Sure! Direct links to the exact parts is here: howchoo.com/g/zjm4zwzjzgi/pi-retrobox-build-your-own-diy-raspberry-pi-arcade-joystick#parts-list
@chriscappello8240
7 жыл бұрын
Jeez I looked at that too and skipped right over it. Thanks!
@Greyswyndir
6 жыл бұрын
Excellent video! Thanks for taking the time to show us how relatively easy it is to make this wonderful little box! It looks sweet! One question about the joystick: I imagine it's an eight-way, so you can play games like Pacman and games like Robotron? How does the eight-way effect Pacman, which originally used a four-way joystick? Does the eight-way joystick still work well with Pac-man, or do you sacrifice a little precision for variety/the ability to play many different games? Thanks again, great job!
@Howchoo
6 жыл бұрын
So the precision is really controlled in the emulation software; I don't think that this (or anything) can ever be a substitute for the original arcade hardware, but I've played a lot of Pacman and this is about as on-point as you can get from home :)
@Greyswyndir
6 жыл бұрын
Good to know. I'm going with the Sanwa JLF-TP-8YT-SK as it's an excellent stick, but I'm sure the one you used was/is perfectly exceptable. The "feel" comes from the joystick's gate (square or octagonal), though I get what you're saying about the emulation itself, very true. Sanwa made a lot of the original hardware we grew up using.
@twochainsandrollies
4 жыл бұрын
I wish I was born with the ability to cut.
@Howchoo
4 жыл бұрын
We could all be so lucky.
@davewoeckener5719
3 жыл бұрын
is this the same thing for the raspberry pi4? I ask because your post is a couple years old now... and I've never built one - but this answers everything perfect except anything to do with RP4. Would a RP4 just be faster and more robust for bigger/newer games?
@alejandrozamora3468
2 жыл бұрын
This is amazing! By any chance, have you tried using the arcade version of Pac-Man, like from those Plug and Play consoles?
@ericjedgar
Жыл бұрын
Would you ever make a magic mirror + retrofit project. Magic mirror by day. Game system at night..
@RunningCordoroy
5 жыл бұрын
Your video is really easy to understand. However, I am wondering why some tutorials wire up a separate power supply for the leds? Do you know anything about this?
@DaMoneyFan
7 жыл бұрын
I did the same case and used your plans. ...I took of the 6 buttons on top and moved 2 of them on top as shoulder buttons...so i have 4 on top and the other 2 on the top side as my shoulder buttons for games like street fighter and mario kart. works great. Was not sure why you had placed all 6 on the top ....thanks
@ivanb4681
6 жыл бұрын
David D. Your setup is dumb lol unless your playing pinball
@Vintiqueture
6 жыл бұрын
Like SF??? This is a normal arcade button layout, which SF started.
@Labyrnthdom
6 жыл бұрын
Pretty damn cool. I'm going to use a couple pcb encoders for big 2 player box. Already have the RBP 3B up and running using a ps4 controller to test the Arcade, Nes, Snes & Sega Gen emulations. Don't really care to have it connect to another system. Going to build a full size arcade cabinet also. With a pc to run launchbox and research. So basically looking at about $100 right from the start for a couple 2 player button and stick kits lol.
@matthewgraton7394
6 жыл бұрын
Can a two player one be built like this similar to the xarcade and also is it possible to use this as a controller for a console
@aaronspacee
6 жыл бұрын
Yeah, don’t yank out the cable in retropie, I thought a theme install was done (it wasn’t) and I pulled the cord out, after plugging it back in, my theme was gone, the thing worked fine, still played games, but the theme was gone and it was all just a white screen with black text and basic animations, an update fixed it but don’t yank cables
@chriscase4726
6 жыл бұрын
Great Video! This was my first foray into building something like this and it went very well. Except for the joystick...I'm not certain why it's not recognized by ES. Any insight? None of the buttons, nor the joystick are recognized. I can maneuver to the 'configure new input' menu, but once I'm there, no recognition of the joystick or buttons. There is power, as the LED lights are on. Any help would be appreciated.
@Hijynx87
7 жыл бұрын
Shit I might have to do this on my lunchbreak. I've got access to saws and drill presses for days.
@brettniquinn6121
6 жыл бұрын
awesome!
@toad2394
7 жыл бұрын
Thank you I'm planning on building it but I need more $
@luxuryhomes8889
2 жыл бұрын
yea sick
@HowDoesOneMeme
7 жыл бұрын
Nice video! Are you ever planning to put out a 3D printable case for the little guy? It would help SO much, as it speeds up the process for me.
@Howchoo
7 жыл бұрын
Thanks! We weren't planning on it, but someone may have modeled something similar on Thingiverse -- let us know if you find a good one and we can add it to the guide!
@massv953
7 жыл бұрын
Why would you 3d print something that is essentially a box when you will get much clearer results with basic tools?
@OmoiSenpai
5 жыл бұрын
Random thought while watching this. Your voice really remind me of Corpse Husband from KZitem haha.
@Howchoo
5 жыл бұрын
Haha thanks, I’ll have to check out my voice doppelgänger
@ocelotmadness6287
4 жыл бұрын
Man havent heard that name in a while.
@Xdatetools
7 жыл бұрын
What would you have to do to have a back lite arcade box? How many LEDs would you need and where would you wire them into the Raspberry Pi?
@Howchoo
7 жыл бұрын
I don't understand -- which part do you want to backlight?
@evanskan6326
3 жыл бұрын
I am going to make something like this with the Pi 4 (and then move on to a tabletop cabinet). Any issues with temperature inside the box? I plan to 3D print the case and need to see if a certain airflow is required.
@sociallyresponsiblexenomor7608
5 жыл бұрын
What blows my mind is why no one has made a damn box or kit you can buy that you would just need to buy a pi and some arcade buttons/stick to just put into it. Instead you have to actually have all the tools and everything to make one, how has no one come up with selling a premade plastic case or anything that does this?
@Howchoo
5 жыл бұрын
Interesting thought Phillip, I'm going to look into this a bit further.
@lkreviews3162
6 жыл бұрын
I built this for Retropie to play NES games - specifically PacMan and Frogger. I setup the joystick and buttons fine in EmulationStation, but they joystick will not work with the NES games. Any ideas? I need a joystick for PacMan, the d-pad controllers are useless for that game.
@asheryunan
6 жыл бұрын
I wonder if they make io shields for the raspberry pi 3 that you could use around the ports
@ezzysoto
5 жыл бұрын
Thank you very much this video help me a lot I just have a question, if I configure my arcade joystick and I wanna go back to my regular control woulndt that mess my configuration? Because I did it with a PlayStation controller and a few days later all the commands were out of order (ex: start move to L2, select to X etc) so now in afraid that if I map my arcade joystick everything's goes out of order, thanks for your help
@tango636
7 жыл бұрын
Still a little bit confused about why are you putting a heat sink on the Ethernet Controller chip instead of the GPU chip underneath the board ? All in all a great project video. Keep it up.
@Howchoo
7 жыл бұрын
Glad you enjoyed it! The ethernet chip is actually one of the hottest parts of the Pi chipset -- check out this heat map: raspberrypi.stackexchange.com/questions/22928/does-the-raspberry-pi-need-a-cooling-system
@tango636
7 жыл бұрын
Great info there man! Didn't know it could get that hot.
@feelingsatisfied
Жыл бұрын
I was wondering if you have any advice on an alternative to the raspberry pi 3b+ as they are extremely hard to find and or expensive since the pandemic. Any help would be much appreciated! Ive been wanting to build this thing for 2 years. Thanks.
@puffball1794
6 жыл бұрын
If you used standoff’s you should have put a heat sink on the chip on the underside of the rpi (SDRAM) instead of the chip on the top left of the rpi (Ethernet and USB controller chip)
@rasteryx123
7 жыл бұрын
Where can I find smaller controllers? more or less than 15 mm,the panel 51x173 mm
@Exodusprime
5 жыл бұрын
I am not mechanically inclined enough to build anything, but I love your design. Have you ever considered making these and selling them already assembled because I am very interested in obtaining one of these for my son.
@Howchoo
5 жыл бұрын
I've definitely considered selling either a kit or a completed unit -- comments like yours will help in deciding whether or not to do it. Thanks for your feedback :)
@Exodusprime
5 жыл бұрын
Well if you do decide to please leave me a message, again your work is incredible.
@Howchoo
5 жыл бұрын
@@Exodusprime I definitely will! And thanks a bunch :)
@sabinshrestha4802
7 жыл бұрын
How did you cut the hole? Can you make a tutorial or say which tool you use to cut the hole?
@daved.5839
7 жыл бұрын
Use a 1 1/4 Whole saw circular blade.
@MrDonescobu
7 жыл бұрын
Dave D. He measured the green button at "about an inch"... The joystick how was also smaller than the button holes... Then he mentioned the white buttons were a bit smaller than the regular buttons.. I'm confused if the guide only says 1-1/4" as a size.. So how would that size be universal for all holes? Wouldn't they fall thro?
@MrDonescobu
7 жыл бұрын
Dave D. He measured the green button at "about an inch"... The joystick how was also smaller than the button holes... Then he mentioned the white buttons were a bit smaller than the regular buttons.. I'm confused if the guide only says 1-1/4" as a size.. So how would that size be universal for all holes? Wouldn't they fall thro?
@railrenegade3040
6 жыл бұрын
If you can hold the drill steady enough, or use a drill press. I found a step bit in a pilot hole on slow speed worked better through the acrylic and the cover.
@gunnarstableford3501
4 жыл бұрын
I love the video. My only issue is that I do not know how to program the buttons or joystick... can someone help me? I'm still pretty new to raspberry pi and python. I'm trying to make my own arcade game
@GTor1226
6 жыл бұрын
Probably a stupid question, but can you use this as a controller even installed with Pi? I.E. can you use this as a fight stick with an xbox one maybe?
@ELO_Dude
7 жыл бұрын
Nice Vid. I converted a Qanba stick with a built-in Pi and external card slot. I would love to know how the power switch and status light are connected to the Pi. I tried one way I saw online and it didn't work. Any chance you can give me the heads up?
@MikaelGuggenheim
6 жыл бұрын
Would it be possible to make two of these, but only have the Rasberry in one and be able to connect the other one to the first one by just a connector of some sort? I like the size of it, but many games for the arcade are more fun when your two players ^^
@Howchoo
6 жыл бұрын
Mikael Guggenheim Definitely! Just put a Pi in only one of them, and then connect its USB cable to the one that has the Pi in it. You only need one Pi, and this gives you two controllers. :)
@MikaelGuggenheim
6 жыл бұрын
It would work like that? Awesome! :D
@Masterchief0521
6 жыл бұрын
You could even use one of those USB extension cables, make a port on the side and keep it super tidy
@kevbou911
6 жыл бұрын
quick question: can we build two of these (like 2 controllers) and plug it onto one raspberry pi? I mean, build one controller with the pi inside the box (as you did) and one controller with juste the buttons and a USB port to plug it in the "main controller"?
@Howchoo
6 жыл бұрын
kevbou911 absolutely! Just build one without a Pi and plug its USB cable into the other Retrobox
@TennisDK-hy7hr
2 жыл бұрын
Love your video. Do you sell one? I never have the time or skill to build one :(
@patokelley
3 жыл бұрын
Dude you should sell these... completed. I bet they sell $200+
@setphaser
6 жыл бұрын
i wish this were a musical instrument
@conejo013
4 жыл бұрын
For the Pimoroni picade hat can I use a different board for the joystick controls?
@bmmcwhirt
6 жыл бұрын
Spend the extra money and get real Sanwa buttons and joystick, you will thank yourself for doing it. Also probably would have been better to position the USB interface board so the port on it just sticks out the back and cut a hole for that. It would just make it cleaner. The joystick here isn't mounted square, I assume that is a space issue, it would drive me nuts, I'll probably go for a slightly larger case just to be sure.
@Reggie1408
5 жыл бұрын
What are Sanwa buttons? What's their advantage?
@yungseed80r
6 жыл бұрын
this sucks. after installing on windows i get no signal in hdmi. tried to reformat and install on mac using apple pi-bake and it takes for ever to write the software. still once done no signal on my hdmi monitor. cables are fine because i can plug my apple tv right up and it displays saw the video about removing the comments in the config file for hdmi to work, howver i cnat even look into the sd card after writing the retro pie image.keeps telling this drive is not able to be read on this computer and would i like to format it? I just formatted it, and wrote the retro pi to it, whats going on?
@joes9545
5 жыл бұрын
This is awesome. Would you be willing to build and wire the hardware for sale?
@felixbrooks7464
5 жыл бұрын
DO YOU HAVE TO DOWNLOAD THE GAMES ON IT, OR ARE THEY BUILT IN RASPBERRY PIE ? AND IF SO,HOW AND FROM WHERE?
@chuyinformatic
6 жыл бұрын
todo me bien solo algunos detalles que se pueden mejorar una de ellas seria los cortes de la caja que se hacen para la Raspberry Pi , en el mercado hay cables reforzados usb cotos que se pueden conectar a la Raspberry Pi y a si evitar que los cables usb que salen de la caja se vean
@TimothyTimPSP
7 жыл бұрын
Cool take on the pi setup there's something uneasy about the video. I can't put my finger on it. Cue cards or something? Ur eyes arnt looking at camera. Video monitor? I gotta know what it is. X)
@Howchoo
7 жыл бұрын
Haha. Well, I actually shot this on my iPad, which makes it tough to know where to look (the actual camera/pinhole small). I set up a field monitor by casting my iPad's display and routing it through an Apple TV, but since it isn't directly behind the camera, I couldn't use it for notes. :) So what you're seeing is the difficulty of shooting on an iPad -- however, as this is only our third *real* video, we're investing in a more "legit" camera soon!
@TimothyTimPSP
7 жыл бұрын
howchoo Okay now my brain can chill Thanks man feel free to point out any oddities on any of my videos. I'm sure there are a few.
@VTVINO
7 жыл бұрын
id buy that
@jackofalltradesllc2116
7 жыл бұрын
was the pie preprogrammed when u ordered it?
@Jordofentdealer
3 жыл бұрын
A pi is always pre programmed. All you have to do is install the os.
@AlphaOmegaKnight77658
3 жыл бұрын
Can the box be made out of cardboard? Or can you build a box straight out of plexiglass?
@Howchoo
3 жыл бұрын
I don’t see why not. However, you might crush the cardboard while playing! You could also use a plastic storage bin I suppose.
@detrw97
7 жыл бұрын
Hey this is awesome! I started today for my son's 7th birthday, which is today. The template for the holes is different then what you are using. Does that matter?
@Howchoo
7 жыл бұрын
Hey there! This is the template I used: github.com/Howchoo/random-bits/raw/master/retrobox/retrobox-template.pdf
@sheriffmenty9968
3 жыл бұрын
Can this be used to play mortal kombat with the 6 buttons?
@josephstiso2
4 жыл бұрын
wouldnt the arcade buttons be lit if the pi is on?
@kiodiekin
6 жыл бұрын
Nice
@CorpLvlNinja
5 жыл бұрын
I know I'm late to the game but will this work with the Pi 2B? From comparing the 2B with the 3, I think it should though the emulation won't be as good.
@Howchoo
5 жыл бұрын
Not late at all! The Pi 2B will absolutely work.
@spycory1
7 жыл бұрын
Is possible buy this? 😃
@Howchoo
7 жыл бұрын
Not currently, but we're thinking about making a kit if we can get enough interest!
@adamgorelik9283
7 жыл бұрын
Yes Please :D
@Sonny377
7 жыл бұрын
you should add powered by hdmi
@levi6241
7 жыл бұрын
its illegal to sell a raspberry pi without a licences i think
@isaacixtupe8983
7 жыл бұрын
I've notice that the Raspberry Pi shows the image on wide screen. Is there a way to change that setting?
@daved.5839
7 жыл бұрын
What size bit did you use for white buttons.?? THanks.
@irencsak
7 жыл бұрын
If a second one was built per the cheaper route, pi zero build, could it simply be hooked up to the first through the usb port to provide 2 player functionality for the games on the pi 3 build?
@irencsak
7 жыл бұрын
Watched through again, saw my answer, sorry Great looking build though, thanks for sharing
@Howchoo
7 жыл бұрын
No problem! If you want to use it just as a controller, you don't need a Pi at all. ;)
@Annie-dx4bv
3 жыл бұрын
This is probably a stupid question but where do you get the games?
@ThysiosX
Жыл бұрын
How hard would it be to make the controller wireless?
@yasefbey5695
4 жыл бұрын
Can i use it for controlling my robot ? its raspberry pi too
@depopa1033
5 жыл бұрын
the joystick is slightly turned, doesn't that equal to unbalanced controls?
@Howchoo
5 жыл бұрын
It would have to be really turned for that to be an issue ;) the joystick uses multiple limit switches
@alankoza1917
4 жыл бұрын
Can i use this setup WITHOUT the pi . Just connect usb end to a computer
@Howchoo
4 жыл бұрын
Absolutely. This is basically a USB controller with a Pi inside of it. Leave the Pi out and you can connect it directly to your computer (or any other device that accepts USB controllers).
@willbe3043
6 жыл бұрын
holy heck i need this for skullgirls
@joostbeukens312
4 жыл бұрын
and the case you use is that a specific case or is it just a random plastic box??
@Howchoo
4 жыл бұрын
You can use other housings if you want but I used a specific one-the link is in the full guide in the video description :)
@josec.6394
4 жыл бұрын
So you need a raspberry for the emulator and one raspberry for every controller, right?
@Howchoo
4 жыл бұрын
I'm not sure what you mean-you only need one computer (the Raspberry Pi itself). If you build one RetroBox, it should house the Raspberry Pi-if you build additional ones, they don't need a Raspberry Pi since they're basically USB controllers. So multiples can plug directly into the one Pi. Does that make sense?
@ien2023
3 жыл бұрын
Notice how he's holding the joystick. You can't have a comfortable controller without a palm rest and this box has no palm rest.
@TheGrebull
6 жыл бұрын
Can you use this with a game made with pygame? assuming that it has been programmed to use the joystick module and buttons without using RetroPie? Thankyou!
@Howchoo
6 жыл бұрын
Yep, this is essentially a USB gamepad containing a Pi - so you can use it with whatever. Even Windows
@potatopear8739
6 жыл бұрын
Where is the file for the housing???????????? Please answer I need this fast.
@plaingaming566
7 жыл бұрын
I have a cheaper and easier way i got a arcade controller and put in the raspbbery pi got a usb hub put drilld holes for it and the other stuff and then closed it and boom btw nice vid
@Rturrito
6 жыл бұрын
You connected the arcade controller to a rasperry pi? Saw some on ebay and want to do that for 2-4 players
@plaingaming566
6 жыл бұрын
so i opend the controller i made some space marked out the holes drilled them connected all the wires inside and there evrything fits in nice
@kunalgupta938
3 жыл бұрын
Can I connect this in led ??
@SinX4Lyfe
5 жыл бұрын
Can you pls link the band saw thing?... Im trying to do this without the knife
@Howchoo
5 жыл бұрын
SinX4Lyfe This isn’t the exact one I have (I have a Ryobi), but this is the same style: www.amazon.com/WEN-3959-2-5-Amp-9-Inch-Benchtop/dp/B077QMBTLP/?tag=howchoo-20
Пікірлер: 265