Hi, so with the email color you just use the color normally and when you done you dip the brush in the color mix? Aren't you supposed to mix them together?
@MonsterHobbiesModelCarGarage
4 жыл бұрын
Sounds good guys. With Testor's paints disappearing due to the Rustoleium take-over, I will have to start bringing in an alternative. This might be the way to go.
@vasili1207
4 жыл бұрын
It's the same as humbrol tbh if you are used to humbrol type enamel...you be fine with this
@MonsterHobbiesModelCarGarage
3 жыл бұрын
@Brysen Isaias Ah...this must be the new Spam for the month? I was wondering when it would come out! - Another guy posted the same thing on another one of my posts.
@statoilbensin2190
2 жыл бұрын
@@MonsterHobbiesModelCarGarage its not a spam its quite true what he is saying. Also xtracolor enamel are in similar tins like Revell and Humbrol. Tamiya enamel is wery good and come in similar jars to Testors.
@MonsterHobbiesModelCarGarage
2 жыл бұрын
@@statoilbensin2190 If you look above, I am saying "Is this the Spam for the month" to Brysen Isaias. I see that he removed the comment since then. - I also don't remember what Brysen Isaias even said. Must have been a whopper! :D
@Slouworker
Жыл бұрын
@@vasili1207 only an idition would use humbrol Revell is pretty bad too, so are their kits
@tristanphillips911
4 жыл бұрын
I got a revel fast and furious car but might be using a different kind of paint.
@silvestersze4411
3 жыл бұрын
Thank you for the paint 🎨 introduction. I saw a submarine in the background, what kit is that? 🤩
@ceoofswag6348
2 жыл бұрын
It’s a U-Boat. I don’t remember which kit though.
@attilioledonne2758
4 жыл бұрын
This is great Almost like the old Humbrol paints. Will you be selling these?
@nevillemadden394
3 жыл бұрын
Br cautious when using the (supposedly) equivalent colours with Humbrol & REVELL. They are Not an exact match. If you are using (let's say) TAN, in one Brand, but you run out of it, and have to purchase the Other Brand, you'll end up with almost a Two-Tone Finish.
@maximolotov
2 жыл бұрын
Can i use this enamel paint to paint bumper of my car in black with sponge brush ? Will it last ? Is primer needed please ?
@zje5086
2 жыл бұрын
i dont think so
@seantaplin581
2 жыл бұрын
What cowboy figure is that?
@JASHVEER22
3 жыл бұрын
Can I use normal thinner or turpentine to thin enamel paint?
@stevensinternationalhobbyd4288
3 жыл бұрын
Either would work
@statoilbensin2190
2 жыл бұрын
I would use lacquer thinner it makes it dry faster. I would recomend a plastic friendly one that wont melt it. Like Tamiya.
@Slouworker
Жыл бұрын
@@statoilbensin2190 Tamiya still dissolves plastic, just less
@keithsimpson2372
2 жыл бұрын
Can these paints be used for models used outdoors ?
@stevensinternationalhobbyd4288
2 жыл бұрын
The enamel paints might hold up okay outdoors.
@statoilbensin2190
2 жыл бұрын
Enamel based will hold wery well outside as long as its fully dried and cured. I would still apply revell clear over to protect the enamel paint further.
@michaelvalenzuela2528
2 жыл бұрын
Which country are the products made?
@statoilbensin2190
2 жыл бұрын
Germany
@WoundedBear2k
3 жыл бұрын
Jack from Bachmann got himself a side gig lol.
@stevensinternationalhobbyd4288
2 жыл бұрын
Jack doesn't work for Bachmann anymore
@gero2190
3 жыл бұрын
Im using revell paints, the ones in the silver cans enamel. How i must clean the brushes and my hands? Wich product i must use?
@greggregson9687
3 жыл бұрын
You can use either mineral turpentine (white spirit) or water based turps. Not sure if water based turps will work in an airbrush though, if that is what you mean.
@statoilbensin2190
2 жыл бұрын
Youse nitril gloves and thin with Tamiya lacquer thinner or Mr color thinner. Use extraction fan or a well ventilated area and a respirator.
@juannick69
3 жыл бұрын
Im painting a ju 88 with email green and its horrible please help me
@statoilbensin2190
2 жыл бұрын
You need to prime and thinn the paint. Also you need to spray or brush it in a room with relatively low dust in the air because you dont want dust in youre paint.
@dasabaja
2 жыл бұрын
Define "horrible". What seems to be the problem? I'm brush painting a P51-D with Revell enamels and they work great for brush painting.
@layne182
3 жыл бұрын
The aqua color is not airbrush ready. It needs thinned.
@DWModels
10 ай бұрын
Totally agree some need so much mixing too
@chanous1
4 жыл бұрын
The only sad thing is their customers service never woth a penny . No replacement concerned a defective tiny can of paint ,they prefer lost me ?
@linkk4624
Жыл бұрын
They sent me grey instead antrizit matt and grey have a lot of water
@nevillemadden394
3 жыл бұрын
You Broke The NUMBER 1 Rule! NEVER Shake Tinlets or Cans of Paint! ..... Not only does it not Mix the Paint Properly, but it Creates Bubbles! You need to STIR Thouroughly! Shaking Spray Cans is a different situation, as they have a small metal ball in them to act like a Paint Stirrer: However, you must Shake Them Up & Down Vigourously for at least One Minute, before, and during application. DO NOT 'Rattle' them from Side to Side.
@statoilbensin2190
2 жыл бұрын
I do that with humbrol enamels with a shake ball in it and I got no problems.
@nevillemadden394
2 жыл бұрын
@@statoilbensin2190 ... Yes, I've since found out that it's okay with a Mixing Ball in it, because Spray Cans work that way. Usually though, it can often cause Bubbles in the Paint. However, I've been informed by a Supplier, that the Mixing Balls are really only for Water Based Paints, when used in Cans.
@statoilbensin2190
2 жыл бұрын
@@nevillemadden394 Well, Mr hobby and Ak interactive sell mixing balls and they both sell solvent based paint. Mr hobby has Aqueous and Mr color and Ak has their Real colors. However I have used army painters mixing balls almost only on solvent based paints. I guess their not meant for it since wargaming paint is never solvent based (unless its aersol sprays). I have never had a problem with any interactions. A mixing ball in water based paint might start to rust but most of the model kit paints that are water soluable are actually vinyl based and I belive that is why they can have metal pigments in them without starting to rust. But Humbrol enamel is often too thick for a mixing ball anyways. But I use to have some thinner in them so they get thinner. I like to use lacquer thinner from Tamiya but for matt and satin the paint will dry too fast so I paint from the tin instead with some lacquer thinner in it.
Пікірлер: 42