Man, you are one of the best people out there for getting an honest review, anyone that thinks any of those problems are acceptable to compete at the price range is out of their mind IMO. It has a ton of potential which I hope I show but out of the box its got a lot of issues like the X8 from TronXY that Isabella and I put together on the Community Build. I think its a TronXY issue
@nerys71
6 жыл бұрын
Eddie Moser the problem is they're both right it can be a great printer while the same time being a horrible printer the problem is they did not handle that replies correctly very unprofessionally being mean and nasty deserves nothing more than a delete so good on you for deleting those immature posters It looks like you handle reviews similar to how I handle reviews twice first I review what I received second like the Mythbusters I get the results and review that my overall review is determined by how difficult it was to get from the first one to the second one :-) and whether or not it was worth that effort to get to that end result both in time difficulty and cost Don't worry about the negative comments just keep doing what you're doing I love watching your videos
@andersstromqvist2211
6 жыл бұрын
Depends on how you look at it. You can get an ok printer for under 300$ but you cant get a great printer for that kind of cash. but if you want a great printer and spend under 600$ it really is a great start and many of the ok printers for under 300$ is not as good base to start with. to some a printer is just the sum of it's parts and many cheap printers will need upgraded psu's and electronics anyway.
@nerys71
6 жыл бұрын
Anders Strömqvist you can get a truly great printer for under $200. Ender 2. I have over 30 printers and it is without question so far the best printer i have ever toucbed.
@ThePhantazmya
6 жыл бұрын
Anders It might be a good base to build on but honestly if you have to replace so many parts, wouldn't you be better off just building what you want from scratch? If you buy this kit it seems that half of your investment is straight up garbage. Any kit should work out of the box without tinkering and replacing half the parts. It's just bad business. If they wanted to sell a "good base" then they should cut the fat and market it as a shell that you put your own heatbed and extruder on for $100 less.
@andersstromqvist2211
6 жыл бұрын
I would not call that a great printer with those limitations. it may be great if you want to go pla only. but what i mean by great it should handel all materials poly carbon etc. Just from the spec sheet you can se that that machine is under powered wich is not a problem if you only want to print pla petg. But there will be nothing left of that machine if you want to extend it's properties.
@AndreGuerrieri
5 жыл бұрын
I believe your review is spot on. It is NOT a good machine out of the box. It's an excellent base for a killer printer if you properly upgrade it. I have one on order and I also have $200 worth of upgrades on order as well. So at around $530 USD, it will out perform A LOT of 3D printers on the market.
@westbaystars
6 жыл бұрын
Love your reviews, as always. I got the TronXY X5S back in September after watching many reviews of it and other 3D printers. After watching many 3D printer KZitemrs for almost a year, I was anxious to get started. And the one piece of advice I heard over and over was that if I wanted to really learn about 3D printing, I should start with a kit. The frame and dual Z-axis lead screws (as opposed to the X5) made this look like a solid printer. And it's the shortfalls of this printer that have taught me a LOT about 3D printing. Having to upgrade the parts to make it print better was what I wanted to do. As I wanted to add a BLTouch, and the firmware was not flashable, I got a different controller. Every shortfall of the printer was a learning experience, which has given me no end of enjoyment as I tune and tinker. A future upgrade is a 24V power supply for the heat bed. I thought it was both 12V and 24V, but that bit from this video really helps me understand the issue. The learning and tinkering never ends. Thank you.
@MCarlzon
5 жыл бұрын
Joined a co-worker in buying this printer and watched your videos after we ordered it.... I know, do research first :) But thankfully for your two videos I know what I have to wait for, I need to prepare myself for what will be arriving and the tweaking I might have to do. This will be my first 3d printer and at start I will do inserts for board games so might work without to much tweaking but thanks to these two videos I know some more effort might be needed to be put in for more advanced stuff and where I can look for good information. Thanks for coming back to the printer and telling us how you got it to work even though the reason for you returning was not the most happy one.
@zachhill9604
6 жыл бұрын
I for one completely respect honest reviews an wholeheartedly support you in your endeavor to provide them to the public whether they be good bad or ugly. Having bought my first 3d printer last year, a CR-10, I did a lot of research before purchasing and thankfully knew what the potential pitfalls were going in thanks to honest reviews. Had I not done that, I wouldn’t have been prepared for some of the common CR-10 issues and would most likely have given up. I know own 3 3d printers, all with pitfalls that I knew about before purchasing, and was completely prepared for them. Keep up the great honest reviews, they are truly a service to the community, I for one look forward to many more in the future, G’day from Aus.
@boogerhead0
Жыл бұрын
Realizing this is a several-year old commentary, I want to say this is an "outstanding" report. I have this printer, sitting in the box, brand new, unbuilt, for several years, while I used my Creality Ender 5+ which has performed very nicely... meanwhile, my Creality Ender-4, sitting with a blown driver, newly outfitted and working with 10s mainboard, has now filled in for the h-bot, not corexy, smaller size models (replacing a Wanhao Duplicator 4)... and finally, I see that I can build the X5S, and with a few good, and needed, mods, have another, great, printer, ready to make parts. You commentary I find very uplifting, and soon I shall set to the X5S. Thanks!
@alanb4778
5 жыл бұрын
As to the 24 volt bed on a 12 volt system, I used the 12 volts from the controller board to close a solid state relay that in turn controls a 24 volt power supply connected to the bed. Got the 20 amp relay on eBay for around seven bucks. It switches the AC going to the power supply. The power supply is an old 24 volt battery charger I had laying around. I like this because the printer controller board is not having to handle the current for the bed so it runs much cooler. And all that ugly equipment is under the bench and out of sight. Thanks for the truthful review. It is a big help.
@PatriotPaulUSA
6 жыл бұрын
Your review was spot on and is much appreciated by 98% of us who watchs these. I bought one months ago knowing it would need upgrading and had problems and its because of the few reviewers who are honest like you. Dont ever stop. Just remember 98% of us agree and appreciate the honesty.
@MrGargoylz
6 жыл бұрын
Thanks for the honesty, Joe! As someone looking to purchase a first 3D printer, it would be extremely detrimental to me to watch a glowing review pandering to a company only to discover their product is a piece of garbage that requires more work than I am able to put into it as a brand new user. Keep doing what you are doing and disregard the ignorant people. I find your reviews to be VERY informative and helpful.
@theoriginaltroll4truth
4 жыл бұрын
Honesty is the best policy! I was looking at this printer and I don't want to have to do too much modding. Know cheap means more work, but honest reviews help us decide. Thank you for you honest opinion.👍👍
@MrGargoylz
6 жыл бұрын
I am amazed that someone would leave hate mail over you being honest. You would think it would be the opposite. It would be more understandable if people were to get mad at you for saying that it WAS the best thing since sliced bread when it is really a pile of garbage. Thank you for your honesty! Your channel is one of the ones that got me into 3D printing only a month or so ago and I am already looking into buying a second printer or doing a MAJOR overhaul of my Anet A8. Keep up the integrity and great videos!
@StefanDembowski
6 жыл бұрын
No hate here, I value your reviews and I think you're unbiased. I listened to the rant and I think you're correct.
@brodytucker3922
3 жыл бұрын
Really Appreciate the clarity and professionalism of your videos. Your Z-offset instruction video saved me tons of frustration. Thank you.
@Ed_Stoddard
6 жыл бұрын
There's always some people who will do a knee jerk reaction in the comments. You have not come this far this fast without doing solid, informational and unbiased reviews of printers. I applaud you for doing what I would like to do, but just don't have the free time. Keep up the great work and thanks for your efforts.
@KevinATJumpWorks
3 жыл бұрын
Absolutely spot-on. As I am typing this, my X5SA is printing a calibration cube behind me and now, after I did quite a couple upgrades on it, it seems to be working just spot-on. It was a great experience to do the upgrades, to get a SKR-board and configure everything exactly how I need it, but you need to be prepared for it. Just like you said, not a machine for a beginner at all.
@0TransAtlantic0
4 жыл бұрын
Glad to see that you are sticking to your honest review. This is just the information that I am looking for, since I have pretty much decided to go with the upgraded version of the Tronxy X5SA Pro. I already knew that this unit has some issues that need to be addressed, and that there are several upgrades that are recommended. The 2019 version seems to come with some of the upgrades you mention, and I believe it will be a great starting point. I just finished building a CNC router from scratch, which was a lot of work, and required quite a bit of adjusting to get everything working properly. Of course I'm already planning several modifications. So building a 3D printer will be a nice distraction. Pay no attention to the haters, your honesty ensures the reviews will be exactly other builders need to make informed decisions. Thanks for the great reviews, keep them coming!
@necasma
6 жыл бұрын
Hi, you're absolutely right. I started with a 3d printer made of metal from scratch. With the learning that I have been seeing videos and forums, I learned a lot, I recognize that I still have a lot to learn. I have a coreXY and a prusa I3. I recently decided to buy a kit on the net. I was shocked by the quality, above all with the lack of mechanical quality, with regard to alignments and correct positioning of the parts to assemble. When I finish my research, I will post videos about all these problems I encountered, and the resolution.
@nightlurker
6 жыл бұрын
Thanks Joe. I bought this printer partly on the basis of your previous review purely because I wanted a printer that is "OK" and that is a good starting point so that I could build a decent printer FROM it, not one that will work out of the box I want to tinker. This shows great promise once I upgrade it first to 24v and then all the other upgrades you (and others, because you are not alone in your views on this machine) have recommended. This is a work in progress kit and should be considered as that when you spend just over $200 for it, which is all I paid.
@Horizoncsafaris
6 жыл бұрын
Well done Joe. The initial review was open and honest.....thats exactly what is needed, not lies and waffle. 300 bucks is a lot of money and people deserve to get a working printer out of the box for that kind of spend. So far ive had 2 300 bucks printer and both were dire out of the box. I felt conned and let down. If I’d spent 100 or even 150 then I’d have expected work and something not quite spot on but not 300! Again thank you for the honest review and please keep down that sir 👍👍
@N.Cognito
6 жыл бұрын
I'm sure others have posted this but Tronxy has fixed alot of the issues you mention. When I get my X5S the belts were parallel, and it came with a 12v bed. The steppers were still turned down too low but they weren't all the way down. I understand your issues with this out of the box. Most of the issues are fairly easy to fix. If someone wants a good basic platform and likes to tinker with things it's an absolute great printer. If someone needs a perfect "no need to tinker" printer it may not be for them.
@nickclarke587
6 жыл бұрын
My example came with dual voltage 12+24V bed and upgraded belt runs. There is now a bracket mounted across the wheels of the X carriage to attach 2 of the belt ends to and the spacers on the idler wheels have been improved... Keep up the good work....
@infernofury5567
6 жыл бұрын
I think I am one of those people in the actual community that loves your videos and is watching this video with a dropped jaw as result of not understanding that people can be so terrible and short sighted.. Reviews need to be honest, and like you said, at least a 100 hours on a machine before reviewing; that is real dedication, that is carrying a heart for what you do, for what you do for other people with the same passion. So therefore I thank you for everything you do. Honestly. ;-)
@StuElliott1980
6 жыл бұрын
Thank you Joe for going back and putting the effort into getting this printer working properly, I stick by my opinion that I don't think for one second that it was intended for a first printer though and your original review bashed it too much for not being noob friendly. certainly turned out to be a pretty good printer in the end.
@ScottMitchum
6 жыл бұрын
Well, I have no problems with your reviews at all. Straightforward and well written so information is presented in an organized manner. It seems to be luck of the draw whether or not you get one of these lower-end 3d printers without at least a few glitches, bad parts/connectors, etc. That is no reason to shoot the messenger! Keep up the great work and ignore the haters...
@grumpy2384
6 жыл бұрын
Hi Joe, Having just watched your original review, I cannot see why people would post negative comments. The review was honest and informative in my opinion. Keep up the good work mate and don't let the haters grind you down.
@_SamUSA_
4 жыл бұрын
I value your reviews above just about anyone else. The reason: UNBIASED REVIEWS. You tell us all about the good stuff and the bad stuff. I bought a 3D printer knowing all the issues, which is great. I got a very good START of a great 3D printer, but out of the box... not so great. I worked through all the issues you mentioned and now have a great 3D printer.
@johnkkkj
6 жыл бұрын
For what it's worth I think you do a great job with your reviews and just generally. I never find you to be fake, or saying positive things because you got a free printer from somebody. You are always honest so with all the hate here is some love. Some people got this printer and they need someone else to validate it, as they can't be objective. I personally don't see the sense in getting a printer and having to upgrade it to make it work.
@KennethBareuther
6 жыл бұрын
Most of us, wants your and other youtubers honest reviews. And I actually think that manufacturers want that to. Keep up the good work and don't let haters get to you!
@LemarinelNet
6 жыл бұрын
Thumbs up to encourage you ! You're 100% right, a honest review is that one that tells the true about how will run the printer outside the box ! I bought a x5s knowing all the things that are wrong with this printer, and I know what I'm going to face when time to assemble it will come ! Go on ! It's a nice review !
@goodgoat3096
6 жыл бұрын
I appreciate the fact that you chose to do a followup video on the Tronxy X5S printer. As a person considering getting into 3D printing the reviews going from "This printer is the bee's knees" to your review which basically called the printer a pile of scrap metal, were confusing to say the least. I have noticed the same range of great to terrible reviews on other printers as well. One item lacking in all; reviews was a discussion regarding print accuracy. In my previous life as a mechanical engineer the Makerbot that we owned was used to make assembly jigs and fixtures where accuracy was more important than print quality. I guess what I would prefer to see in a review of a 3D printer would be: 1 performance "out of the box", 2 performance improvements with minimal, low dollar, modifications, and 3 maximum performance with unlimited (almost) modification. If that is beyond the scope of what you would prefer to do, so be it. Most of the review videos comment on at least one of the shortcomings of the X5S printer, and there are others offering relatively inexpensive solutions. Now there appears to be a new model, the X5SA which offers auto bed leveling and possibly more, hard to tell. I guess that a little confusion is typical of a new technology. I look forward to your review of the Tronxy X5SA
@damianfirecaster7230
6 жыл бұрын
Thank you for giving an Honest Review of this printer. It is a CHEAP printer :), but it has Great potential, no the electronics are not good they suck, but we still Love it. Im New to 3d printing they told me I was crazy to get this printer, but I did , I learned Fast how to Rebuild a hotend, how to keep this printer from jamming, I lost two hotends, to jams in the screw pipe, bought new ones, rebuilt it and got no james for 20 prints, then I left the filament in the printer between prints and it jammed again in the same place. so I rebuilt my hotend a Second time. got it back working great, I ordered 4 more 40mm pipes and Steel nozzles. once i get the steel nozzles I will Rebuild the hotend better. I want to try out carbon fiber and nylon filaments. so again Thank you for the truthful reviev of the TRONXY X5S. She has issues out of the box but so much potential. keep making these great informative videos. Thank you Damian :)
@dren2547
6 жыл бұрын
I feel you made many good points in this video and the original review and can't fault anything you stated. I appreciate your honest opinion and believe you have the community's best interests at heart. Keep up the great work and thanks for the awesome videos!
@docrenatoms
6 жыл бұрын
Your channel is the best one. I learned a lot from your lessons and I think your reviews are the most honest possible. So, don't waste your time with these haters. Congratulations!
@totbenru
6 жыл бұрын
I love your content and the way you present yourself with honesty and empathy. You, Joel (3DPN), Cody's Lab, to mention a few, are the nicest persons on Earth. Haters will hate, trolls will troll. I would just enjoy the ride. Magandang umaga from PH!
@johnstewart1266
6 жыл бұрын
Don't let the hecklers get you down. I think you did a fine job giving us a great unbiased review of the printer in your first review. What they don't understand is that you give us your time just to give us an honest opinion. I would just like to say thank you for all your hard work.
@SimonMenu
6 жыл бұрын
Do not take care about haters, you're doing a really job, it is a pleasure to watch your videos. Keep going !
@VincentGroenewold
6 жыл бұрын
Oh this is great stuff, your explanation is simply spot on. To say these issues would be ok is just ridiculous. Thanks for being honest and critical where you should be critical! And btw; really don't focus on hateful comments, I mean, the positive majority always is silent.. this is KZitem, haters never accomplished anything.
@ThePhantazmya
6 жыл бұрын
We need more people to be more critical about these products. Just because the community is full of tinkerers who are able and willing to throw more time and money into a kit to get it working nicely doesn't mean that everyone is. I don't want to pay 300 euro for a buggy mess that I have to do major surgery on. Even if I wanted a kit to doctor up and make my own, I would still expect a working printer out of the box. If I accept buying a kit that is less than plug and play, then I want to know what I'm walking into so I can factor that into my calculations and comparisons. So many reviewers gloss over the negatives and just try to sell you the machine without giving a thought to who is the appropriate buyer of that machine and what that person is going to expect. Keep being honest and thorough.
@JamesBYo1
6 жыл бұрын
When you do a review, you have to give the good with the bad! I appreciate an unbiased opinion over "buy this!" "most awesome printer ever!" I'd rather know what I'm getting into before hand, and your reviews are awesome! Made some impulse buys because of popular opinion and regret it at this point. Keep up the good work, and keep the unbiased reviews coming!
@bbutoob
6 жыл бұрын
It was good that you shared your findings. . . Otherwise few people out there would have even thought about adjusting the motor current pot. In your previous review my first assumption would have been that you didn't adjust the belt tension evenly, thus causing the layer shift. Kudos!
@jessescott9704
5 жыл бұрын
Great review and glad you pointed out the shortcomings for those thinking about getting this printer. Great job!
@randomguy7253
6 жыл бұрын
I've got mine last week, and they've changed a few things: - 12V heat bed - 5 minutes 20° to 60°, but the cabling gets HOT, and mine was missing a solder joint so only 2/3s heated up - better belt routing, including a second metal plate at the X carriage for belt mounting - metal mounting plates for the Z motors The file names on the SD card say "v2.02". But this printer definitely has its fanboys that behave like a**holes. Your review, with the stated target audience, was correct.
@WMCLComputers
6 жыл бұрын
I have been following you since your first videos... there are only a handful of people that can create really good content and you are one of them. My first 3D printer was a Creality CR-10 because all the reviewers where telling amazing stories and I had nothing but problems since first day. I did tons of mods to try to make it a reliable machine, ruby nozzle, bondtech extruder, insulated heated bead, noctua fans, marlin firmware, otoprint all and many others... I ended trowing it to the trash because of all the frustration, then I went for the Monoprice Select Mini, had to modify it and upgraded too now I have ordered a Prusa i3 mk3 and I have not blame anyone for my mistakes or my bad luck with printers... I have learned that there is a lot of work and effort that you need to invest on this bunch of trial and error and the technology is simply not there yet... but without people like you that inspires others and try to put out there a honest review the frustration would be even bigger and the and the community would simply not be as good as it is. Keep your hard work.... you a great at this you have gone a long way to let ignorant people to take way your passions....
@StichtingSCHERP
6 жыл бұрын
9:28 Yes! exactly! Thank you Joe for staying honest in your review, this is the reason I watch your channel!
@techoutreach5647
6 жыл бұрын
I never understand all the hate over a video. I respect your videos and some others thats why i watch. If someone does not agree with your review there are plenty other reviewers out there. Keep up the good work Joe and I for one really like your reviews
@donaldwright2426
5 жыл бұрын
Never owned a 3D printer. For this past week, i have been watching and reading a lot of reviews. From me to you, I like your honnesty! I was dispointed when I saw you first review of this 3D printer because I was so pleased with a low price tag for a coreXY type 3D printer. Knowing all the problems, and knowing that there are solutions, I will problably buy this model knowing the risks. Thumbs up and thanks ! :)
@cardonagulihermino672
6 жыл бұрын
ain't easy being honest and haters always gonna hate so don't get bothered by them! I love your reviews. YOU ARE THE MAN
@skullcraftcustoms
3 жыл бұрын
I bought one as my first 3-D printer my average prints are 6 to 16 hours and they come out flawless I’m exceptionally happy with my purchase I can’t believe it only cost me 300 bucks
@richardb2382
6 жыл бұрын
Respect for totally honest review. I’ve bought this printer, but the new x5st version. I know it has issues, they have actually resolved the belt alignment issue, but still could be better, they should just do away with the bearing and washer idler solution, and just pay a few pence more for a proper gt2 idler. Fortunately, I’m a printer engineer by trade, so not daunted at all by what needs doing to make this a superb unit. Already ordered corner brackets, don’t see the point of printing them when correct aluminium ones for 2020 profile are available. I hate Philips screws being used so have sourced Allen bolts to replace every one. Mine will be dual mosfet, dual psu and probably lots more mods before it ever makes a print.
@wibble1999
5 жыл бұрын
100% AGREE. im a nrwbie, bought a tronxy x3a on the strength of reports and groups saying it was awesome. It sat for a year assembled but prints were unuseable. utter crap. Now ive 12 months under my belt and my anycubic kossel is goosed awaiting spares Ive taken my ecperience to date to try to sort the x3a. How many others got caught the same way due to the nasty bar stewards who had a go because you spoke the truth. It doesnt say requires years of experience and tuning of motors etc because even if you follow our build guide it wont work. as we in the uk say "sod em" MY FRIEND. YOURE ONLY EVER HONEST TRUTHFUL AND FAIR
@PrestonBannister
6 жыл бұрын
As a point of information, your review helped me decide to order a TronXY X5S. I fully understand what I am getting into with this kit. This is my second printer (the first is a decent i3 clone). I can print the needed upgrades for belt-routing and frame alignment/stiffening. Will likely add an A/C heated bed, and replace the electronics - though in stages. There is an odd aspect of psychology when folk have to struggle a bit, they tend to become invested, and defensive/aggressive. Years ago this was DOS "power users" who claimed they would *never* use Windows. Designing a CoreXY printer, but got hung up trying to do something clever with Z-motion. Bothered by the fact I cannot work on later aspects. Can use the TronXY printer to go through the exercise with A/C heated bed, and perhaps the g2core software. So you helped. :) Update ... Largely satisfied after some upgrades: www.thingiverse.com/thing:2861239
@josheh4
6 жыл бұрын
Good to see others plotting the same roads I am. I'm very interested in this printer, since it's a larger corexy. Thanks for sharing your experience, and the link. I had an i3 clone that I brought up to the level of the likes of Prusa's genuine printers. I've been debating if I can do that again, or if this would be too cheap of a base to start from.
@mzakelj
5 жыл бұрын
@@josheh4 I also buy as second printer. And after i watch the few revies, i just simple print the upgrades before the printer arive :D
@anthonyrich1592
5 жыл бұрын
Thanks for this. I have a Tronxy X5S-2E on its way as a second printer, so I'll probably be trying out some/all of your upgrade parts.
@DaveKester
6 жыл бұрын
keep up the good work. If I'm not watching your videos understanding that your opinion is just that then I'm missing the entire point of channels like this. I really appreciate your attention to detail and your thoughtful approach. :)
@stuh4645
4 жыл бұрын
I just ordered one and all my reading agrees with everything you said, even the Facebook group people are pretty open about the potential of the printer and how to get there. I'm a tweaker so a project printer suits me, its fun to know when I get the unit I can start printing parts to improve it. It will be my first 3D printer so it will be a learning curve!! :D
@FriedPi-mc5yt
6 жыл бұрын
Don’t worry about the haters. I’ve been looking at various reviews for 3D printers. I thought your review was honest and well reasoned. I don’t want to spend my hard earned money on something that’s less than what it should be. I can’t imagine who would want to spend money on one that will need a new heat bed right after they open the box. Not to mention the lack of documentation to tweak motor current correctly. Okay, there is a community of people out there that can help you get the motor and alignment issues corrected. But still, short comings are short comings and I for one appreciate you suffering through the time spent with it rather than me doing it. As I said, I don’t want to throw out a bunch of money and I’m looking for a Dad and Son project printer. So I think I’ll be going for the Anet A8. It looks like something me and son can start printing with and upgrade as we go. I liked your review on it and it seems like the best bang for the buck project printer out there.
@FilamentFrenzy
6 жыл бұрын
Awesome and honest as always 😃 But this video is of high significance you just past 150 uploaded videos, congratulations 👍 here’s to another 150
@PapaNutz
6 жыл бұрын
Ignore the Hate, as a newbie to 3D printing I appreciate an honest review. It gives me the right information that I need to make the best decisions as to what I am going to spend my limited amount of money on. Noting what can be improved etc.. is nice, but I'd much rather know what I'm getting right out of the box. Keep up the good work and just ignore those haters, they are always going to be out there no matter what you do.
@nathansanders8613
6 жыл бұрын
I like my X5s after doing several upgrades. It is my 10th 3d printer and 3rd printer kit. Prints super great!!! Worth the money for sure!
@ldboehm
4 жыл бұрын
You are right, your review was spot on, bravo for telling the truth! For some strange reason I bought the TronXY X5SA Pro, and it is so far not a good experience. Seems that physically it is created very well, but support is horribly lacking. This could be a great printer if they actually added support to tell users how to use it properly. Barely any documentation, email support is not enough. Shifts during large prints. I'm left to basically figure it out on my own. Build videos all have questions. I asked for documentation on supported gcode and they needed me to open the power supply to send a picture of what board I have, then sent me firmware for me to decode. I can't even tell what flavor of gcode it uses so I can slice with other slicers, like Slic3R
@damianfirecaster7230
6 жыл бұрын
Oh forgot to tell you, I have the upgraded version of the TRONXY X5S printer, the belt attachments on the carriage are now separated so the belts are now going straight , it also came with updated firmware Marlin 1.1.7. so the maker is listing to the community about the issues with this printer. I ordered mine straight from china, took over a week to get here. next we need to get them to change the power supply to 24v so it has the power it needs for the hotend and bed and stepper motors. Thank you Damian
@wesleyels3847
5 жыл бұрын
Thank you for actually helping and highlighting the most important aspects of this printer and where the faults lie. Now I know what to expext if I were to buy one. Keep up the great reviews!
@Chris173972
6 жыл бұрын
No hate here. I love your honesty and I am glad you are not one of these sponsorship "I love this printer" after making just a benchy channels. Keep on doing what you are doing. Ignore the haters.
@MrMike-fn4hi
6 жыл бұрын
Joe thank you for choosing to maintain your integrity despite criticism! I would unsubscribe if I thought any content creator was simply a Shill to keep Gearbest or any Manufacturer happy. There are too many "reviewers" on KZitem that flat out lie to promote their channel and keep their supplier happy. If you want to hear that everything is all sunshine and rainbows go watch another channel. No need to give a guy a hard time for giving his honest opinion. The review clearly showed his reasons that brought him to that conclusion. The fact that Joe puts at least 100hrs onto a machine before a review is a considerable amount of time and it should make his experience more valuable to you.
@christelledeneau7461
6 жыл бұрын
I agree with you Joe, we need more honest people like you. Keep up the good work !
@Bajicoy
4 жыл бұрын
A friendly reminder that presentation defines people's views more than the information that it contains. I know this video is years old now but as an observer reviewing videos for inspiration the lesson still holds true. Just because you are giving the truth or believe you are in the right or are trying to be helpful, it does not mean others automatically must obey. On a more productive note, I wonder how tronxy created such an avid following and defense for the printer. Was it really just the pricing per advertised feature set?
@Entferenten
6 жыл бұрын
To be honest Joe, I can credit you, Tom Salanderer (probably misspelled that), Joel, Makers Muse, RCLife, Nerys, and a few others with giving me the gumption to even begin this hobby. My first printer was an Anet A8, and I have followed your feed religiously since that review. I now own a CR-10 and a Tevo Little Monster... You (and everyone else I listed) are my “mentors” in this strange journey! I appreciate your honesty and candor. I’ve followed your channel with great interest and enthusiasm, and this is only my second ever time posting a comment. Don’t let anyone change who you are, and keep doing what you’re doing. I am relatively new to this hobby and the insight that I would have to “rebuild” this printer out of the box is invaluable to someone in my position! Thank you for all you do and keep at it! Let the hate be like water off a duck’s back and soldier on!
@moriconanjohn
6 жыл бұрын
Honest talk and great reviews! Don’t bother with those narrow minded. I enjoyed so much watching your channel. I got also this kit and trying to modify it as a beast. Indeed this needs a lot of work. Definitely not for the beginners.
@MightyJabbasCollection
6 жыл бұрын
The whole point of a review is to point out the good and bad points of a product - not to gloss over them or make excuses for it. While it may be true that it can be made decent with enough work and extra parts, that’s beyond the scope of a review IMO and you really went above the call of duty even making this follow-up video. Don’t let the haters get to you, Joe.
@josheh4
6 жыл бұрын
3DMN, thanks for these videos. I was looking at the X5S-400 as a possible starting point. I appreciate that you were honest with the issues. My focus in looking up information on the Tronxy X5S printers is to figure out what's junk, what I'll have to fix/replace, and if the cost of that is worth it. The information you have provided has been helpful.
@israelcontreras5332
4 жыл бұрын
I always appreciate your honesty. Screw the haters! Keep up the awesome work! I hate it when reviewers go cheap on their reviews and say something is good when it isnt.
@mcrotbot
6 жыл бұрын
hey, its been about a year since I last looked at your channel, wow!!!! I was really surprised you have grown by leaps and bounds. I'm pleasantly surprised keep it up man!.
@Jbravo88-m4y
6 жыл бұрын
Sweet revised review, I like it that you took this out to light, some people forget to use reason and facts, which can benefit the manufacturer to correct or revise the manual or parts to the customer collecting info on their search for the printer that suits them. Like always your content is super helpful cheers!
@wyukigurumi
6 жыл бұрын
Hey man, i didn't see any hateful comments, but sorry to hear that you're so upset about it. Btw started printing on the Tonxy 5XSA, 40x40x40... not sure f X5S is the same. I had the same issue, but I found a way to address one of the issues you mentioned. The leveling was a pain when i found the hot tip is closer to the bed in the middle and further from the bed near the edges. I at first thought the bed was curved, but I found the problem. The left and right rods in the middle with the screw threaded pole are fastened so tight, its arching the aluminium frame. Once I loosen them, there was a stress release *clank. And when i did a leveling again, the hot tip moved relatively flat across the whole hotbed. I had to balance the tightening of the left and right middle rods as if its loose I will get rough surfaces.
@brianpercival1829
4 жыл бұрын
Great review. Every 3 D printer that comes out all have room for improvements. Name any printer and there will be blogs and videos of upgrades. The manufacturing companies do a fairly good job getting a printer to the market at an affordable price. I agree with you on the power supply, it should have been matched with the hot bed. I am doing some research into Tronxy as I am looking to buy a Tronxy x5st-500 as I like the big build feature, 'go big or go home'.
@dandare2586
4 жыл бұрын
Thanks for the reviews......it's one year later and I believe tronxy have improved on many of these issues, but not all. Having been looking for a 500mm + height core XY printer that could print flexibles, the minimum cost for non Chinese is going to be more than $3500 + 800 for an enclosure. So that is a big theoretical budget with which to address the issues with this printer, as far as I am concerned!
@SpotterSky
6 жыл бұрын
Hi Maker Noob I find your videos quite good and enjoy them because your reviews seem serious and you are a capable 3d printer enthusiast. All the people who just write a trash can talk and do not participate in a serious debate about the products you show and that you should also have your own opinion about as certain youtubes do not respect or can comprehend in their heads serious is not worth listening to! It's good that you can distinguish between dirt and cinnamon :)
@junkieball
6 жыл бұрын
Your rant is absolutely spot on. Honest reviews is a must! One of the main reasons i watch your videos. Keep up the great content.
@NativSarussi
6 жыл бұрын
Well I'm not a kid but I did saw a few very positive reviews on the x5s... So I went and bought, actually the x5sa (by the time I decide to to buy it the X5SA came out) I'm a bit disappointed but as it turns out the x5sa had some issues from the x5s addressed... Wish I saw your review. Thanks for the honest review! Keep it up.
@shyamdevadas6099
6 жыл бұрын
Screw the haters, Joe! Even if someone makes a mistake, its no reason for uncivil, or rude behavior. No excuse for it! Most of us know your character and the quality of your content. Your initial assessment turns out to be absolutely correct. You said that you may as well spend a bit more money for a finished product than a hinky kit. Well, if after all of the discoveries about this printer, if it still takes over $200 (plus my valuable time) then you're talking about an initial gross capital expense of over $500. For that much, I can buy many excellent printers that AREN'T broken out of the box. (Personally, anyone who would embrace the concept of buying a crappy kit and spending more time and money to make it function doesn't understand the difference between price and value, or the relationship between time and money!) Sorry you had to endure this nonsense.
@CzKaa
3 жыл бұрын
I was bought upgraded 24V version - because this is very good base for good printer. Exact. :)
@rondlh20
6 жыл бұрын
I think your review was very good, you report the issues and solutions. Afterwards solving the problems is always trivial. Keep up the good work. Don't waste your time deleting ignorant messages
@TerenceMurrayWolf
5 жыл бұрын
I have to agree with you on this, I'm looking at the Tronxy x5s as my next 3d printer and as an owner of the anet a8 which was a nightmare in one respect and extremly educational on another I wish someone had given me more info on it... I knew going in it wasn't perfect but thought I could handle it and I did but not living in a country that had easy access to parts and upgrade materials was a pain. Thanks for your honesty.... Oh and yeah I'm still probally going to buy one, lol.
@keith5031
6 жыл бұрын
Just ordered this printer and should get it in a few days. Even with all the downs sides, I think this can be a very good printer. This is my second printer. Spent a lot of time getting the other one up and running, it came as a kit also. Will definitely be upgrading all the different parts. Not sure about the bed though, as I don't print anything in ABS. I'll use my Prusa i3 for that I guess. Keep up the vids, I love 3d printing and only do it as a hobby. Definitely a learning curve to it, but there are a lot of groups and people out there to help if you are willing to ask.
@richardruark6422
6 жыл бұрын
Thanks Joe... I enjoy your reviews and believe you are extremely fair and unbiased. It is appreciated when you give reasons why you like something and why you don't. Along with criticisms and praise, you give reasons and instructions on how to correct some shortcomings, and if it is worth doing and at what cost. Thanks again Joe..... Keep It Up!
@davec3275
6 жыл бұрын
Thanks for your honest reviews and going the extra mile to make an informed review of a printer. I know I bought a printer based off of a glowing review and had a mountain of issues. Come to find out that I wasn't alone. More honest reviews.
@ianide2480
6 жыл бұрын
Thick skin my friend, that's all you need. I've been watching your channel for a while and just subbed today. I appreciate the production quality, time, and thought put into your videos. Your reviews are already better (much better, in fact) than most of the popular channels, and on par with a few others. I wish I could say that "I've learned so much" but the truth is I have really learned very little from any channel. I watch mainly to see what's new and get design ideas. I'll eventually have one of each of the 3 popular designs for 3D printers (delta, core XY, and I already have the cartesian). I had a ton of fun designing and building this printer and I look forward to the next one. Hell I'm still not done tinkering with my current printer. I'd rather tinker than print hehe... I'll just continue enjoying your content and please, keep up the good work.
@djberg3483
6 жыл бұрын
I'm not even subbed to your channel, but I did watch the other vid. Honesty is a hard pill for some to swallow, believe me, people hate me for my brutal honesty. Anyways great follow up, and keep the world updated as to how you make out with it. Be safe, DJ
@lolcorporation7308
6 жыл бұрын
Thanks for being unbiased just delete and ban anyone for saying you should be biased it's unacceptable
@ChunkyJo
6 жыл бұрын
It's a kit. What do people expect? It's NOT the best 3D printer for under $300 like everybody says, because it's a kit. Time is just as much a commodity as money. People raging that the Tronxy is best because EVENTUALLY, with enough time and extra money (and assuming you already have a second printer to print addt parts for) you can get decent prints w/ it? Come on. Be real, people. That really sucks man. I didn't like your vids when I first started watching you, don't know why. But you've quickly become one of my favorite 3D printing channels. LOVE your vids. I can tell you really enjoy doing it and that you do it because you enjoy it. That's hard to convey via video. Anyway, keep it up and pay attention to me, not the neckbeard haters who are too emotionally invested in their printer.
@KevinRank
6 жыл бұрын
I think this is a good review. I feel many times, there is a disconnect between many reviews and the products. I started out with a Tevo Tarantula. I KNEW what I was getting into. I knew it was a kit that needed upgraded. Out of the box it is passable, but not great (though, I'd contend it has fewer... issues, than this printer). When you purchase a printer like this, I guess I expect to make upgrades. That is the cult of DIY, behind them. Since I have zero knowledge on this printer, I am surprised to hear other say how great it is. I will sing the praises of the Tarantula... with the strong caveat that you are looking at a month of upgrading it, slowly, since it will not be amazing out of the box. It sounds like this printer is the same. All in all, I think this is a great review, and a great way to handle things. I think these DIY kits require a "newbie" review like your previous one... and then one like you just did talking about some upgrades to make it print better.
@Dieselfitter01
6 жыл бұрын
Great job on all of your content and how you stay true to the here and now. Keep doing what you are doing as you have been and will be because we all know you aren't manipulated in any way. Thank you for being you.
@netwolfstar
6 жыл бұрын
Just getting back into 3d printing after a break from it, really glad to see your still making helpful videos. Don’t worry about the haters they, armchair warriors with nothing better to do than criticise. It’s your channel and your opinion and if they don’t like it they can tune out.
@raspberrypiploy771
5 жыл бұрын
I am surprised and disappointed that you have had so much hate. For me your reviews are my first point of call in my research for a new printer. Sometimes I may not agree with something you say but that is why research is subjective as are the reviews. I personally trust your reviews and am very grateful for your efforts and the ease at which the reviews can be understood. Some people can be just plain rude and ungrateful. Don't let them get to you and never feel you should apologise for the reviews you make. You will 'never be all things to all men'. but at least you make the effort ;-)
@forrera168
6 жыл бұрын
I'm glad I saw this video, because I bought one JUST BEFORE I saw your previous video. Keep up the good work. Thanks
@jymacdougall74
6 жыл бұрын
Joseph, it is better to warn others of issues than to not say anything. Anyone who deals with manufacturing of any product knows that even the best made thing may have issues and in a production run there are outliers that make the product look like crap. It is up to the buyer to decide if they want it or not and it is up to that buyer to research as much as possible to purchase something that they will be willing to accept possible issue that may come up from set-up, practice, and actual use. We don't want them to happen but they may. You are doing selfless act for your time and energy of reviewing and helping others to understand things before purchasing. And I can say with absolutely certainty you do it well.
@Keeping_IT_Simple
6 жыл бұрын
Sorry to hear you've had some nasty people putting bad comments here... Please don't let them put you off , the rest of us value your professional , interesting & best of all honest reviews highly ... Keep on doing what you do so well!
@topedesigns2683
6 жыл бұрын
This video explains why I like your reviews so much. Keep the good work and think that haters are like fans but with a strange ways of showing their love ... by the way, I love your work !!!!!!!
@darren990
6 жыл бұрын
your the man you say it the way it is and no one pays you to say it .great vid like allways joe
@TheMiltonfen
6 жыл бұрын
Thanks for what you do Joe. Sending Love. Mark Like you I got a Trnxy when that's not what I ordered and they have a lot to answer for. I've now joined my local Makespace so I can use their printers to make replacement parts and get it working.
@muckademuck
6 жыл бұрын
Thanks for the impartial review! I'm considering this as my next printer and based on your review (and a couple of other honest ones out there) I know what I'm getting into and can plan ahead. Again, keep up the good work.
@killjoy554455
6 жыл бұрын
For someone getting in to 3d printing. I like reviewers with honest reviews. Plus out of all my research I have been doing. There is no such thing as the perfect printer out of the box. They all need some sort of tweaking.
Пікірлер: 385