Designers:How many guns do you want to have? Full Armor Unicorn Gundam:YES
@sddmf4165
Жыл бұрын
Did you topcoat it after decal & panel lining or otherwise? i'm new at this hobby, seeing you building this make me want to have one too someday
@Armstudiogunplaspeedbuild
Жыл бұрын
Yes panel line, decal then flat topcoat
@J1m._.
3 жыл бұрын
nice
@Armstudiogunplaspeedbuild
3 жыл бұрын
Thank you
@ryEzero1three
3 жыл бұрын
Damn! That looks amazing! dis you use Matte or Flat top coat?
@Armstudiogunplaspeedbuild
3 жыл бұрын
I use Tamiya TS-80 Flat clear.
@ryEzero1three
3 жыл бұрын
@@Armstudiogunplaspeedbuild thanks man!
@marcuskwok9313
2 жыл бұрын
@@Armstudiogunplaspeedbuild did u put it back to unicorn mode then apply matt top coat or did u do something else
@Armstudiogunplaspeedbuild
2 жыл бұрын
@@marcuskwok9313 topcoat each part then assemble
@chuggi9592
Жыл бұрын
Beautiful build. I have a question that I noticed because I’m trying to apply top coating in the most efficient way possible without covering the clear parts. Did you break the build in sections before you would apply the clear parts,those sections would be top coated and only then can the clear parts be applied on. Using this would decrease the time of build by a significant number as you don’t need to top coat every individual pieces but rather combined pieces. If this is confusing , I just want to ask if you top coated every individual piece by it’s own (except clear green parts) or not?
@Armstudiogunplaspeedbuild
Жыл бұрын
I normally apply topcoat by section like arm, leg, head, etc. If these sections have some clear parts, I will use masking tape to cover it. I dont like to apply topcoat on clear part becuz it will become foggy. For this kit, It is different. Before building this kit, I think about 3 different ways to apply topcoat. First, turn it to unicorn mode and apply topcoat. I dont like this way becuz the age of armor wont be applied and also i dont think the armor will close perfectly. There will be some gaps and the paint can go inside. Second, turn it to destroy mode and use masking tape. This will take time to mask. and I think it gonna be difficult to mask this kind of part. The last way, apply each piece and assemble later. This way will consume a lot of paint especially when you use spray can. However, I think this way will give the best outcome for this kit. Yes I chose this way. No need to do this on backpack becuz there is no clear part on it. Just assemble and apply the whole part.
@user-yj5js7ux8j
Жыл бұрын
I am building the same unit next week. Wish me luck. I'm gonna start make the base version first cause my panel liner and topcoat come so late😢
@ArkadiosTheodulus
3 жыл бұрын
Which RG is your favorite?
@Armstudiogunplaspeedbuild
3 жыл бұрын
My favorite RG is Tallgeese. it is simple and solid kit. Which is your favorite?
@ArkadiosTheodulus
3 жыл бұрын
@@Armstudiogunplaspeedbuild Not sure yet. Am still building RX-178 and already bought Tallgeese to eventually build. The Sazabi, Nu, and Unicorns all look great too.
@ehhirfxan2524
3 жыл бұрын
Nu gundam so best to build. How about rx 78 bro ? I plan to build it latter
@dagreenshark
3 жыл бұрын
I think mine is Unicorn or Nu Gundam. Maybe Tallgeese will be even better.
@ehhirfxan2524
3 жыл бұрын
Is it topcoat before built bro ? Look so flat colour ❤️❤️
@Armstudiogunplaspeedbuild
3 жыл бұрын
yes I normally apply flatcoat after built but for Unicorn, I do before becuz I dont want clear parts become flat.
@ehhirfxan2524
3 жыл бұрын
@@Armstudiogunplaspeedbuild how many bottles you used bro ? Mr hobby topcoat or tamiya ? You do straight on runners or after cutting
@Armstudiogunplaspeedbuild
3 жыл бұрын
@@ehhirfxan2524 I used 4-5 cans Tamiya TS-80 for RG Unicorn. But for other RG kits, around 2 cans. I always paint after cutting.
@ehhirfxan2524
3 жыл бұрын
@@Armstudiogunplaspeedbuild thank you bro :) thx for information ❤️
@justinjoshuaheller
3 жыл бұрын
Could someone tell me what i need to build him like that? So the exact names of colours and other stuff. I am new to this.
@Armstudiogunplaspeedbuild
3 жыл бұрын
Tamiya panel line accent color black for highlighting panel lines Tamiya x20 enamel thinner for cleaning up excess, use with cotton bud Tamiya TS-80 Flat clear spray can for matt finish
@cesruhf2605
3 жыл бұрын
@@Armstudiogunplaspeedbuild is it better to have grey panel line color or black?
@Armstudiogunplaspeedbuild
3 жыл бұрын
@@cesruhf2605 Both are great, It depends on your taste. Grey is good on white color.
@cesruhf2605
3 жыл бұрын
@@Armstudiogunplaspeedbuild makes sense, also did you topcoat because I usually don't
@Armstudiogunplaspeedbuild
3 жыл бұрын
@@cesruhf2605 I topcoat all my kits. It is a quick way to give painted look to the kit.
@duongnphong
Жыл бұрын
very nice build!! should I buy water decals for this kit?
@Armstudiogunplaspeedbuild
Жыл бұрын
I didnt use. But yes water slide decals will be better.
@jasonstimson6617
8 ай бұрын
Dude get the final Battle ones or whatever, that’s what I ordered and they’re sick. Last battle water decals newtype
@vuviethung6999
3 ай бұрын
How are you supposed to loosen the unicorn shoulder joints? Could you pls tell me the most efficient way to not broken the joint
@Armstudiogunplaspeedbuild
3 ай бұрын
Yeah i know it is stiff but i didnt do anything. just turn it.
@vuviethung6999
3 ай бұрын
@@Armstudiogunplaspeedbuild ok thx for your reply
@zepher31415
3 ай бұрын
Submerge them in hot water from 3-5 minutes, then try turning if they are still stiff or you feel strong resistance give them a few more minutes, that's what I did to mine.
@Armstudiogunplaspeedbuild
3 ай бұрын
@@zepher31415 That's brilliant bro. thank for the good trick
@driftsc2gaming779
Жыл бұрын
We’re these the stickers that came with the kit or did you buy them separately?
@Armstudiogunplaspeedbuild
Жыл бұрын
The stickers came with the kit
@Ipannn_31
Жыл бұрын
helo , how to remove stress mark when cutting nub marks ? because its very annoying. If this confusing i just want to know how to cut gunpla parts cleanly like you did
@Armstudiogunplaspeedbuild
Жыл бұрын
There is no way to remove stress mark from a cut, only can minimize. I normally use art knife to clean up nubs. I also apply flat topcoat to my kit. It will help to conceal stress mark. The only way to completely remove stress mark is paint over it.
@cp2445
Жыл бұрын
Is this better than the FA MG ver ka?
@Armstudiogunplaspeedbuild
Жыл бұрын
I haven't built FA MG
@ronaldjbsantos1980
4 ай бұрын
Choosing between this or RG Sazabi 🤔.
@Armstudiogunplaspeedbuild
4 ай бұрын
Get both
@yapjack468
2 жыл бұрын
What did he use for the V-fin The gold film
@yapjack468
2 жыл бұрын
I need it to build my future unicorn
@Armstudiogunplaspeedbuild
2 жыл бұрын
I used masking tape on white behind and painted gold
Пікірлер: 56