NOTE!!!! Before testing capacitor DISCHARGE FIRST. To safely discharge a capacitor you will need a 20,000 ohm 5 watt resistor, two insulated screwdrivers and two jumper wires with alligator clips on both ends. Connect one jumper wire clip to one wire of the resistor and clip the other jumper wire to the other resistor wire. Connect the clips on the opposite ends of both jumper wires to different screwdrivers, hold the handles of the screwdrivers and touch the blades to opposite terminals of the capacitor. Good video, for licensed Oil Burner Techs.
@gabbytaveras5650
2 жыл бұрын
This is INCREDIBLE info if your a boiler tech resolving riello issues
@JohnMullee
Жыл бұрын
With control box removed: jumper control box terminals 5 and 6 to allow motor to run without firing the burner.
@JohnMullee
Жыл бұрын
Verify 39 to 51 VAC between 3 and 7
@JohnMullee
Жыл бұрын
Box away and power off: 1.3 ohms between 2 and 8
@JohnMullee
Жыл бұрын
Box away and power off: 1350 ohms between 1 and 2
@JohnMullee
Жыл бұрын
3 and 9, detached, capacitance 12.5 microfarads.
@JohnMullee
Жыл бұрын
Clockwise for more pressure, oil pump
@Ratman_Bejo
3 жыл бұрын
Riello Burner Best is the best
@radhakrishnan2980
9 жыл бұрын
good video thanks for your narration.Keep it up and continue such tutorials. bye KR Radhakrishnan.
@skhasanur4857
2 жыл бұрын
1 year baad nozle Kharap ho raha hai too kya kare Please battao ?????
@skhasanur4857
2 жыл бұрын
Dezle barnal. Or Gas barnal are function same???? Please sir boliaa???
@Bob18818
Жыл бұрын
Great video 😊
@ArcheryRuleZ
3 жыл бұрын
I like that pressure gauge , & connector , what kind? I’ll order one
@h7opolo
2 жыл бұрын
16:19 oil burner continuous run operation procedure
@marvinfuentes6942
3 жыл бұрын
This is a good Training video.
@ДмитрийКуликов-ц4и
9 жыл бұрын
Мы приеменям такие горелки и котлы в наших проектах модульных котельных. Мы строим такие под ключ, по нормальным ценам #Водогрейная_газовая_модульная_котельная_МВКУ_3,2ГД
@karlwarnes6062
6 жыл бұрын
very helpful info on testing stuff,learnt a bit.Have a read of rustyshak 1 comments may just save your life.
@rotechent1528
3 ай бұрын
Price
@culayta
11 жыл бұрын
What make and model volt meter are you using?
@kirk0respite
12 жыл бұрын
Very informative.
@Jim89240
5 жыл бұрын
These things are way out of my league, spent over 4 hours on one today, then fixed a beckett in under and hour right after my riello debacle
@laothakao
11 жыл бұрын
What is the resistance of the cad cell????
@ArcheryRuleZ
3 жыл бұрын
probably needs to be under 2000ohms but i dont know how to read the resistance. i just replace the cad cell and nozzle / check specs if it wont run
@aneeshp.m5506
5 жыл бұрын
Can u explain seguence controll wiring
@rosscrompton1
5 жыл бұрын
Contact Riello website or tech support for more info or documentation
@burnershack8900
11 жыл бұрын
Total Darkness (over 150k Ohms) Good light (Less than 40k Ohms) Good Job Ross
@ArcheryRuleZ
3 жыл бұрын
shouldn't it be wayyy less than 40k ohms in good light? just wondering because other burners should be less than 2000ohms thanks
@Ratman_Bejo
4 жыл бұрын
I think you can see some good
@wraiger1
7 жыл бұрын
That was confusing as hell. It jumps around and is too vague.
Пікірлер: 39