belle démonstration sur vos outils un point sur le risque des jets HP (EPI)
@drain119
2 жыл бұрын
good
@epkk82
3 ай бұрын
Hej man, what is song?
@dourryrojas6701
2 жыл бұрын
Mi tuberia del lavabo lo tengo tapado como consigo un equipo de eso mil gracias si me puede atender
@danielbello8008
2 жыл бұрын
Que equipo se ocupa para que funcione así con esa presión de agua ?
@nozzlesandthings2562
2 жыл бұрын
40 l/m 200 bar 22 cv, un saludo!
@PARKERBROTHERSPLUMBING
2 жыл бұрын
name and where to buy these nozzles?
@nozzlesandthings2562
2 жыл бұрын
www.robertobruna.com write to info@robertobruna.com
@BigDogRidgeback
3 ай бұрын
Jet rodders
@JorgeGarcia-qm2xv
2 жыл бұрын
Greetings We have a piece of equipment that works at 4200 psi, 4 gpm with a 1/4" hose and cuts the roots perfectly without any problem, I don't know why you say it can't. It's a matter of ingenuity and patience. And another Electric equipment of 3000 psi, 5.5 gpm with a 3/8 "hose is 220 at 3 phases and cuts the roots perfectly.
@nozzlesandthings2562
2 жыл бұрын
Of course, roots were also unblocked with rods and with a spring machine many years ago, it was also a matter of ingenuity and patience. I mean that for a professional it is not appropriate to go with this type of flow to cut roots. It also depends on the size and number of roots. Maybe I got confused that it can't be done, I meant that it can't be done professionally. There are many tools with which they can be done, there are also electrical equipment without water... We recommend at least 40 l/m to remove roots and we agree with most equipment manufacturers.
@silosvince
2 жыл бұрын
I have a 3500 psi pressure washer with 4.5 gpm. Do you have a nozzle that will cut roots with this kind of machine?
@nozzlesandthings2562
2 жыл бұрын
None of our nozzles would work for that flow rate, you will not be able to cut roots with that flow rate, that water simply does not have enough strength to be able to do it, there is no nozzle and if they want to sell it to you, do not buy it, it will not work with you. that flow. With 40 l/m you can start working on those roots, but no nozzle with chains will work for you, you can only do it with a nozzle with 2 jets, like the Tarantula, since you concentrate the force in 2 jets, and you would have a force of 20 l/m for each jet, for small roots you would be able to remove it.
@carmeloalvaropatlangonzale3631
Жыл бұрын
Tienes algún contacto para poder encargarte una boquilla
@nozzlesandthings2562
Жыл бұрын
Escribenos a info@robertobruna.com o llamanos al +34 685 86 89 04
@FranciscoPerez-dx8xe
Жыл бұрын
Hola para comprar una punta de estas
@nozzlesandthings2562
Жыл бұрын
Escríbenos a info@robertobruna.com o llámanos al +34 685 86 89 04
@FranciscoPerez-dx8xe
Жыл бұрын
Me interesaría el número teléfono o donde lo vende
@nozzlesandthings2562
Жыл бұрын
Escribenos a info@robertobruna.com o llamanos al +34 685 86 89 04
@sulanginaja
8 ай бұрын
This number Whatsapp?
@FranciscoPerez-dx8xe
Жыл бұрын
Qué número tenía yo lo que llamada número de teléfono
@nozzlesandthings2562
Жыл бұрын
Escríbenos a info@robertobruna.com o llámanos al +34 685 86 89 04
@JorgeGarcia-qm2xv
2 жыл бұрын
Give me your email and I can send you videos of root cuts
Пікірлер: 27