Nice job---but just as an FYI---you don't need to completely remove the rocker assy to install the "Lockers", just make sure there is "No load" on the Rockers and do one bolt at a time.--just an fYi.
@jimirox1928
6 ай бұрын
I Installed Rocker Lockers on my Softail a few years. It used to sound like two skeletons screwing on a tin roof but now it's nice and quiet.
@fishandgameman
2 жыл бұрын
Whatever you do, make sure the blind holes for the breather bolts are void of any oil. Swab the hole with a Q-Tip or blow it out with shop air. The hydraulic pressure from any remaining oil will blow out the underside of the head before you even get near the torque specs. Those breathers can be counter intuitive during assembly and it’s easy to get them wrong. Don’t ask me how I know. 😆 If you get confused, check out the video, “My Harley Blows” (It’s dipstick). Nice video! 👍
@A7007
2 жыл бұрын
May i ask if the rocker locker have a life time ?? And for how long would last before i need to change it
@Richard5873
2 жыл бұрын
At 4:51 I do not have to put piston at top dead center before tightening base plate bolts down ? Just like when adjusting push rods. I'm doing thing project this weekend. Great video Thanks for Great information
@efakter1
Жыл бұрын
How did you get that bushing out? Because that just happened to me
@rrmorris67
3 жыл бұрын
the 2005 Road King 88 I recently obtained is so loud on the front cylinder i can't believe it. I sure hope this fixes it. I've had a Yamaha V Twin for 25 years. I'm not prepared for Harley quirks.
@matt8863
2 жыл бұрын
3:00 Is that camera trickery or are those bolts reverse thread??
@Christopher-cd3pc
2 жыл бұрын
Must have been mirrored image or something
@smrtrbl86
Жыл бұрын
He used his cell phone is forward facing camera mode. Makes it all look reverse. You can tell by how he tightens the bolts reverse instead of clockwise
@smrtrbl86
Жыл бұрын
At 4:05. What do you mean radius on the pin?
@goodboyringo9716
Жыл бұрын
Rocker locker didn't stop my Twin Ticker !
@johnjohnson2855
9 ай бұрын
What years are these for
@bm7760
3 жыл бұрын
I've a set on order. Hoping it cures the top-end rattle that's driving me nuts. Then I'll sell this POS and buy a decent bike.
@romesyoutubechannel5356
Жыл бұрын
I'm with you bro... and that's exactly what I'm going to do.
@PkwyDrive13
4 жыл бұрын
Please tell me I don't have to drain the oil or anything to do this? I literally just did an amsoil 3 hole oil change yesterday..
@Rick-Williams59
4 жыл бұрын
Nope, you don't have to drain the oil, I've used them in the last 2 Harleys I've owned.
@jimscycleandautotn8508
3 жыл бұрын
Um.... Nah just turn the bike upside down and all the oil will float to the top
@dulian08
3 жыл бұрын
There is a better way !! You drill a hole on the bottom square to the pin and tap it then bolt down a Allen stopper to the pin !!! They will never move again.!!
@simplex4297
2 жыл бұрын
Yep ,the better way is called the Tim Stone method right here on U Tube.
Пікірлер: 21