if you keep uploading cool prodjects this channels is going to be big soon trust me!! keep up the good work!!! :)
@ChipGuy
3 жыл бұрын
854K subs @ 24.01.2021: You were right mate.
@karenhotaru3702
Жыл бұрын
2,22 M subs @ 20.02.2023 :) :) :) You were absolutely right!
@willlycos5781
12 күн бұрын
3.36m subs in 2024 GOOD CALL!. loving the story of this channel
@jarnevanhecke7913
12 күн бұрын
@@willlycos5781 damm 7 years ago…
@m00str
8 жыл бұрын
Bauhaus! Wenns gut werden muss!
@YOLOgamer-yq8yf
5 жыл бұрын
ik wist dat hij duits sprak
@ChipGuy
3 жыл бұрын
Bin da ja eher bei "Jabadeia jippi jippy jay"
@PunakiviAddikti
7 жыл бұрын
If you want to include the button into the circuit, why not make it cycle through colours for the power level indication instead of having a set color for each potentiometer, as well as cycle through all the different power levels for each potentiometer to see them without having to turn the potentiometers? There's a lot of things a single button can do when connected to a microcontroller. I'm sure you'll find a use for it! If you just want something simple, how about a toggle flip-flop with power indication light? One press, power is on and the button lights up, second press powers the device down and button light turns off.
@rajveerthankia4347
8 жыл бұрын
Nice video, love your videos and congrats on 1,600+ subs
@Nerdforge
8 жыл бұрын
Hey, that's fast! Thanks a bunch, means a lot :)
@rajveerthankia4347
8 жыл бұрын
+Natural Nerd np :), just keep on making these great videos
@soniccinos
4 ай бұрын
4:11 So, that's the dammed table saw......
@creeperzone2215
7 жыл бұрын
i saw the parts and was like NAW, FUCK THIS! Then i started doing it, and i was like YEA, I GOT DIS! After it was done, i was all like NAW, FUCK THIS, IT NOT WORK!
@zaprodk
7 жыл бұрын
You should connect the 5V to the 5V pin on the Arduino. The voltage regulator on the Arduino needs about 1.5V extra to regulate properly, so the VIN-pin takes from about 7.5V and up. Connecting 5V to it will result in less than 5V on the Arduino and possibly unstable operation - not recommended.
@colinwhitehurst9781
7 жыл бұрын
I want to do something like this, but I would like two knobs for each light, One for color and one for dimming, so I can set the hue and the level of each fixture separately, but then also Have one master knob at the bottom that when turned would allow the master knobs to set hue and dimming levels to all ligths at once. No clue how to do this, but I want to one day, haha
@Nerdforge
7 жыл бұрын
I wanted to do something like that originally as well, only with warm/cold white to be able to adjust the warmth. Shouldn't be any different except for the code :)
@colinwhitehurst9781
7 жыл бұрын
Yea, my problem is that I've never done anything other than wire an outlet in my house or tin speaker wires. Not really sure exactly where to start to get the point I could pull off this box! I have a solder gun though lol!
@Nerdforge
7 жыл бұрын
I understand how you feel! I hadn't touched a soldering iron two years ago, and I'm still pretty bad, hehe
@sirauthentic7387
7 жыл бұрын
I work daily with Soldering Irons and suck so badly with them
@PunakiviAddikti
7 жыл бұрын
I can solder fine but Arduino code is too complicated for me to understand. I find coding PIC microcontrollers with Flowcode 7 is easier due to the simplified interface.
@amogh_kumar
8 жыл бұрын
Cool, any 12V led lights will work. 1 Suggestion You could have used lilypad arduino, since you are not using many I/P ports right. Its cheaper than mini
@hydrogeddonn
7 жыл бұрын
That board reminds me of my digital electronics class where it took me four days to finish a simple detector project because my breadboard was dead. My design was flawless but after 3 days the teacher decided to test my breadboard and low and behold it was broken. Lost so much time on that single project. Is the Arduino easy to learn? I have experience with AOI, NAND, NOR and XOR circuit design but when it comes to macro electronics I'm a bit lost.
@Antiganos
7 жыл бұрын
CBA judging by your post I'd say you'll be able to figure out an Ardi just fine
@FoneBone27
8 жыл бұрын
Nice job. you only missing schematic. Heia Norge :) godt jobba.
@h2o1969
3 жыл бұрын
What a fun project.
@AdrianoCattini
7 жыл бұрын
Very well done!!! maybe in some years you could do the same project but taking care of the things that you think could be done better, I'm gonna make my own now :D
@blackdragon8854
7 жыл бұрын
very nice. good job, man.
@BuiltandTested
8 жыл бұрын
This is fantastic! Love all your videos.
@Nerdforge
8 жыл бұрын
Thanks, means a lot to hear that :)
@23abbu
7 жыл бұрын
Nice job, awsm vid, was planin to make smthing similar... Wld be great if u cld like put up a schematic diagram to make things easier to understand
@1337million
7 жыл бұрын
Just guessing from some comments that you're Norwegian, but if you're thinking of doing something like this again you could alternatively try some long-shaft/Gibson-style potentiometers. There are some cheap ones at gitarist.no :P
@nicotrinker1608
7 жыл бұрын
sorry for my bad english ... but if you add a socound slim layer of wood between cables and acrylic it would be looking a lot bettter ... nice job and very good video
@Nerdforge
7 жыл бұрын
Thanks for the tip!
@ChipGuy
3 жыл бұрын
Hansi: "This is a blue button" Martina:"What does it do?" Hansi:"It lights blue". (It's a movie reference)
@miguelmont4576
7 жыл бұрын
you should to use an arduino pro mini insted of arduino nano. Pro mini is cheaper and is smaller and better for this proyects
@MrSn3akr
7 жыл бұрын
You should have flipped the acylic around so the larger holes were on the backside.. Then the buttons would have gotten the a better grip on the potentiometers
@johnlawrence3434
6 жыл бұрын
This entire project would have been easier for you if you would have used your table saw more instead of a scroll saw. Also, invest in a cheap acrylic cutter for making straight cuts. It's much easier to score it a few times and snap it cleanly than to try to follow a straight line with a scroll saw or jigsaw. It's a great project though.
@mishukdas4210
4 жыл бұрын
Hey, you are doing some really great work. I am greatly inspired by your work. I wanted to ask you that if i try to control the wireless led floor lamps that you have made with this control panel. Do i need an arduino or an the same node mcu with microphone module can be used? And i want to add an oled display to show the brightness and modes of the lamp. Is it possible with the equipments that were used in the floor led lamps project?
@dishantkashyaprock
7 жыл бұрын
A Bluetooth module would work great for this project so that you can operate that by your phone , also there are numerous app available for operation.
@neeleshmaurya7017
7 жыл бұрын
i am not able to understand that where to atach potentiometers pins can u please help me out i really want too make this for my home
@davidsamuels6734
7 жыл бұрын
AWESOME!!!
@Nerdforge
7 жыл бұрын
Thanks!!!
@gitarsimen
8 жыл бұрын
Very cool project! Do you know how much output current it can deliver?
@Nerdforge
8 жыл бұрын
Thanks! I think the mosfets are rated for 5 amps, so it would be 5 amps for each output channel :)
@Stoney_Eagle
7 жыл бұрын
Using a board with 3 holed islands is so much easier and less messy
@mohammedmuzammil5554
8 жыл бұрын
mind ===== blown boom thats really cool
@paulrevenberg9297
7 жыл бұрын
i'm pretty sure you can just attach the 12V to the arduino nano and it'll work
@Nerdforge
7 жыл бұрын
Thats right. But with these cheap chinese knockoffs I might as well not take any chances, and run it on 5 volts, as that is needed for the strips as well.
@MrC0MPUT3R
7 жыл бұрын
Nice shirt
@evusworks
7 жыл бұрын
uhhhh. you should check just put the 12vdc power supply to the Vin of the arduino. the arduino has its own regulator. thats one less component to buy .
@Nerdforge
7 жыл бұрын
Could have done that, but I wouldn't want to run all those LED-strips through the Arduino anyway, so I'd use the same component nontheless :)
@evusworks
7 жыл бұрын
+Natural Nerd then bypass the 5Vdc power supply. connect the 5Vdc to the Vcc of the arduino or the 5V pin on the arduino. this way you would bypass the regulator and remove any unwanted voltage drop.
@Nerdforge
7 жыл бұрын
👍
@PunakiviAddikti
6 жыл бұрын
I'm afraid the small linear regulator on the arduino would get extremely hot. I believe it's either a 5 or 3.3V regulator, in both cases with current draw of 50-100 mA and 12V input it will get very, very hot, and isn't gonna be very efficient. True, that would be very handy and eliminate one extra component, but when the linear regulators fail, assuming also the temperature cutoff fails, they fail short and will kill the arduino.
@lean5639
7 жыл бұрын
This is an old project, but if you can, please provide a schematic
@Engineer.Critics
8 жыл бұрын
wow nice and amazing its great video
@oscar1arce
7 жыл бұрын
Where did you buy the LED strip Good video.
@Nerdforge
7 жыл бұрын
Thanks! Here is the full list, including the LED-strip link: Supply list: Arduino Nano | goo.gl/6plPSl Potentiometer | goo.gl/KK4wvi Knobs | goo.gl/VftEsk Mosfet | goo.gl/BnON8z Voltage step-down | goo.gl/ISlIJ3 RGB LED-strip |goo.gl/sR7f5P Button | goo.gl/mcp5b3
@Nerdforge
7 жыл бұрын
Saw it and fixed it! :)
@oscar1arce
7 жыл бұрын
Thanks, it's perfect, a good video
@kaizuk7389
7 жыл бұрын
I love the shirt lol
@alexcantlow8559
7 жыл бұрын
Should of put a false bottom on it to hide the electrics but apart from That I like it
@gloriaash7511
2 жыл бұрын
❤️
@nehabkeinyoutubesry
8 жыл бұрын
wait, where are u from? i saw a " bauhaus" thing, thats a german company :D
@Nerdforge
8 жыл бұрын
Norway! We've got the Bauhaus ;)
@nehabkeinyoutubesry
8 жыл бұрын
ouh nice ! im from germany :D
@fazellama5933
7 жыл бұрын
I want to make one of these but this is impossible
@MarkusSeidl
7 жыл бұрын
You have so beefy mosfets, it’s a pity you are using so tiny tiny cables and bridges on the PCB...
@nomisgamer2236
7 жыл бұрын
very nice i wish i could do this but i am totaly lost ahahahah
@joakimjohansson7729
7 жыл бұрын
From Sweden? :)
@Nerdforge
7 жыл бұрын
Norway :)
@jeanpi314
7 жыл бұрын
wow
@benji376
7 жыл бұрын
Norsk?
@viktorsheep
7 жыл бұрын
Lion with STFU tho... :D
@samuelbauer9226
4 жыл бұрын
You looked quite cute 3 years ago😍
@tehuloste2544
7 жыл бұрын
0:34 My ocd....
@tehuloste2544
7 жыл бұрын
3:51 YOU HAD TWO TRIES
@herrjonna2007
7 жыл бұрын
Er du norsk? subscriba!
@linushg55
8 жыл бұрын
Are you Swedish?
@Nerdforge
8 жыл бұрын
Close! Norwegian ;)
@TheOrginalHumibold
8 жыл бұрын
but got the german materials?
@yassinemaftouh
2 жыл бұрын
.2022
@robertm.6243
7 жыл бұрын
this soldering gave me cancer
@bassriot6335
7 жыл бұрын
its probably better then yours, cuz if youre so good u should know how hard it is to begin with....
@RolandBanc
7 жыл бұрын
Same here
@Nerdforge
7 жыл бұрын
Likewise :/ But it's getting better by the day
@DoctorRose
7 жыл бұрын
srsly? thats not cool.*swivels head* *sigh* oh well... lost cause i guess...
@8blieb8
7 жыл бұрын
To elaborate on your comment ( I too am terminally diagnosed, get it terminal), its not his soldering skill that is awful its his misuse of components. If you use PCB prototyping board, never use random wires, just use solder to make lines by connecting holes. This prevents corrosion from breaking contacts and allows for higher current operation. Secondly, never ever solder an IC components (apart from transistors) directly but always use header. A good rule of thumb is if its legs are long and flimsy (like that of a resistor) solder it, if it has short hard legs that fit in header, use header. If you decide to solder IC components directly there is a big change you fry them due to the heat of soldering. Also, never use electronic components for mechanical support (linking two separate boards using an arduino). This is just bad practice that in extremes can lead to mechanical stress on the component breaking it. This almost never happens but people usually don't walk on the street naked and there are still laws prohibiting it. My source is an electrical engineering minor. I understand the hostility but to be fair natural nerd channel seems to generally not do electronics to well and most mistakes are very basic that could be prevented by watching a couple of youtube videos.
@akaya0166
7 жыл бұрын
Bist du Deutscher?
@akaya0166
7 жыл бұрын
ok ja bist du weil ich hab grad den Bauhaus Zollstock gesehen
@timhoewner4554
7 жыл бұрын
in der Kanalbeschreibung steht Norwegen
@Nerdforge
7 жыл бұрын
Bauhaus in Norway too!
@akaya0166
7 жыл бұрын
Lol :D
@_who_cares_1123
7 жыл бұрын
あかや -さん Bauhaus. Wenns gut werden muss!
@jasonwhite5553
7 жыл бұрын
Whole project poorly executed. Adding a switch for no reason, knobs seemingly have no use (What do the other two knobs you didn't touch do?), soldering job was exhausting to watch, really dude? You soldered your microcontroller straight to your board? That was your first answer? The pins of the Arduino. Jesus. Disaster at all levels. Plan dude. Plan.
@PunakiviAddikti
7 жыл бұрын
Well that's a bit harsh, not to mention rude. I don't see anything wrong in soldering a microcontroller straight to a PCB. It won't destroy it, and these small Arduino boards are cheap. It's no different from soldering a normal IC to a PCB, the only significant difference is that this one has a micro USB socket for programming it directly. As for unused UIs, with a microcontroller there are no "useless" inputs. Assuming from your hostile attitude, I assume you're better at this?
@jasonwhite5553
7 жыл бұрын
It's unfair to compare, I'm on a different level. However, even at a hobbyist level...he needs to read more, watch KZitem, Google, practice soldering. Long before he decides to make an amateur video that teaches hopeful learners awful practices and behaviors.
@santiagobirkenstock
7 жыл бұрын
"unfair to compare" If you are not better, have a better attitude or shut up ffs
@jasonwhite5553
7 жыл бұрын
Unfair to compare because I'm building larger electric projects on a different scale than home hobbyist. I didn't point this out because it's unnecessary and my point stands.
@wouterfransen9771
6 жыл бұрын
Jason White your arrogance is next level
@MRnoob_MRnoob
7 жыл бұрын
du är verkligen inte händig....
@rtzi2352
7 жыл бұрын
German?
@luisdumuihual1490
8 жыл бұрын
horrible.
@Jonas-wq4iy
8 жыл бұрын
Jealous?
@Jonas-wq4iy
8 жыл бұрын
Jealous?
@Hellsong89
7 жыл бұрын
Soldering was kinda horrible, but the wood working part was even more cringe worthy, then again i'm not that good with, coding so i guess everyone has their own strengths and weaknesses..
Пікірлер: 112