Thank you for this video. My BB just started creaking so I gotta clean it and put it back together and this vid will help me out. ❤❤❤
@damian4288
Жыл бұрын
Thank you for this tutorial, it helped me a lot with my Vegast crankset
@davidddmaoqiu
4 ай бұрын
Thanks! Did you use the 2 spacers you showed earlier in the video?
@geothunder1971
2 жыл бұрын
I'd defiantly recommend using a little lithium grease with the graphite added to the drive side crankarm and chain ring interface, I've had issues with it creaking and the grease helped a lot.
@zaff_zuhairi3885
2 жыл бұрын
Where did exactly u put? Is it on the teeth of the spider? Because mine creaking alot also after about 3 weeks of putting a new grease
@geothunder1971
2 жыл бұрын
@@zaff_zuhairi3885 I put it on the crankarm where it contacts the chain rings and I've had good luck pulling the cranks out of the bottom bracket taking the crank arms off the spindle and greasing any contact points including the spindle where it contacts the bottom bracket bearings, no creaking at all!
@rgpeters
Жыл бұрын
Have you tried Loctite 609 or Parktool RC-1 with AP-1 as well? You can see what I mean with this video done by BBinfinite kzitem.info/news/bejne/ynl-mnlvoHR0iGk
@lucacostantini8361
Жыл бұрын
Ciao! A cosa serve l'ultima brugola che stringi?
@DeMuffinable
2 жыл бұрын
Hi there, thanks for the video, I'm trying to build the exact same setup as you but with Aldhu Carbon cranks, but I have a qns. Does the non-drive side bearing preload ring come with the spacer set/cranks or must be purchased separately?
@yonglingng5640
Жыл бұрын
It should be pre-installed on your left crankarm.
@martinherrera1020
2 жыл бұрын
En Colombia. Dónde compro unos platos así. ????
@johnwright2312
Жыл бұрын
How do I remove crank please?
@thebikerei
2 жыл бұрын
Do these 2 big spacer rings come with the cranks?
@lill1671
2 жыл бұрын
nah not on mine ones
@DominikLoeffler1
Жыл бұрын
It's an optional spacer kit that you can purchase with the crank. Since this frame is a narrow BB30 you will need it, many others won't
@trekmadone3225
2 жыл бұрын
No mention of the Weight?
@veloperso5314
Жыл бұрын
Hi, crank arms: 355-385g depending on size. Axle: 99g. Spidering 160-200g depending on size (46/30 to 53/39, oval is heavier than round). Carbon arms are 255g average.
@nadhifrevisyach5878
2 жыл бұрын
What spacer is it? Are rotor 30mm spacer?
@DominikLoeffler1
Жыл бұрын
They are Rotor 30mm spacers for installation in frames with a narrow bottom bracket shell, like this Specialized with BB30
@veloperso5314
Жыл бұрын
You use spacers when the width of the frame with BB installed is below 86mm. You're supposed to mount spacers with BB30, BB386, BBright, PF30. BB86 and BSA do not require spacers expect de 0,5mm included with the axle.
@eugeniocastillo1074
29 күн бұрын
Cuanto será el precio y si es bb30
@eugeniocastillo1074
29 күн бұрын
Bcd30?
@DominikLoeffler1
Жыл бұрын
Nice video, thanks! But BB30 🤦♂🤦♂ those big spacers are ugly. BB386 ftw
@joshgross8741
2 жыл бұрын
I would break those tiny teeth. How is the crank holding up?
@fame1382
2 жыл бұрын
No complaints so far. It's on a Allez sprint frame btw.
@PtWhiteBelt
2 жыл бұрын
If the Pros from BH Burgos don't break them I think you're safe.
@christianguichard3772
2 жыл бұрын
Nul, aucun commentaire et la caméra ne filme pas certaines manipulations.
Пікірлер: 29