RKT Keebs literally just popped that keyboard open with zero effort! Other reviewers crying about how hard it is to open the case up 😂
@rktkeebs
9 ай бұрын
its in the technique 😅
@DigitalNomadexe
9 ай бұрын
BRO i watched them pop this open like that and I'm like "TF!? how did they do that!?" I was on the struggle bus tryna pop this thing open lol
@elliotbaltazar
9 ай бұрын
@@DigitalNomadexe Dude has got skills!
@macuujovne7676
10 ай бұрын
do you recommend putting some other mods other than tape? like switch pad or foam?
@rktkeebs
10 ай бұрын
you can try just replacing the foam with eva but it will be very thick and hard to close for the switch pad the silicon is already a 2in1 (plate silicon and switch pad in one)
@quack9355
8 ай бұрын
PE foam and a lil bit of Polyfill instead of eva. Would recommend changing switches even if it's Akko pros. RK switch sounds so bland af
@BackyardniJuan
2 ай бұрын
I just bought last night and I paid around 35 usd because of the discount and voucher
@Yummymoto_WR
6 ай бұрын
Hi, may i know what did you do to make the rubber feet stick again after removing them to remove the screws?
@Sillymonke712
5 ай бұрын
Just use any glue like superglue
@k4ii03
Жыл бұрын
So it does have a pc plate, gasketmount, and silicone foam
@rktkeebs
Жыл бұрын
yupp royal kludges first gasket mount
@ash-bp2nb
5 ай бұрын
how do u remove the blue and red wire bruhh
@jg3936
10 ай бұрын
What did you use to remove the knob?
@rktkeebs
10 ай бұрын
just an angled tweezers
@davebillones840
Жыл бұрын
newbie here i ordered H81 online and it's on its way. that was my first mech keyboard anyways, may I ask what is that silicon like above the PCB? If I plan to put PE foam, can I put it together with that silicon thing? Thank you and subscribed!!
@rktkeebs
Жыл бұрын
i dont recommend putting another layer of pe foam as the silicon already acts like the epoch mod already 2 in 1 epoch mod and plate dampener
@davebillones840
Жыл бұрын
@@rktkeebs i see Thank you for answering. Really appreciate it. 😁😁
@marcusgoh8408
Жыл бұрын
Hello! What tape did u use for this?
@rktkeebs
Жыл бұрын
mtx tape
@Reynalaa
Жыл бұрын
can u do a flex test on the rk h81 ?
@rktkeebs
Жыл бұрын
as for the flex test I tested it and it does not have much of a flex because of low space inside of it hence i didn’t put EVA case foam mod as it will reduce the flex even more
@jcorc4
7 ай бұрын
Rk81 software link pls
@huutidang7662
Жыл бұрын
can you measured that knob for me?
@rktkeebs
Жыл бұрын
25 mm for the diameter
@samuelebr3474
Жыл бұрын
@@rktkeebs Pode mandar o link do knob ?
@samuelebr3474
Жыл бұрын
@@rktkeebs um de 25mmx15.5mm,6mm serve ?
@samuelebr3474
Жыл бұрын
@@rktkeebs O knob com 6mm halfshaft serve nele ?
@bacau3633
Жыл бұрын
please give the spin button link
@rktkeebs
Жыл бұрын
i found it on shopee its called potentiometer knob
Пікірлер: 34