Thanks for sharing this-It helped me check my RS 50's oil pump, also left a like :)
@gazmtg
13 жыл бұрын
Hey steamfrog. Yeah I was running premix. The oil flow is fine. I just needed
@gazmtg
13 жыл бұрын
Hey steamfrog. Yeah I was running premix. The oil flow is fine. I just needed to see that there was oil flow.
@AimlessMoto
7 жыл бұрын
You running premix to do this test I hope? lol
@Frag3r99
8 жыл бұрын
so on my 50cc oil pump is removed (the pipe) and i need to premix the fuel everytime, should i try to fix my oil pump? Is it hard and is it worth it? im just tired of premixing and the guy who had my bike before me turned it off, maybe the pump is broken i dont know but its it worth it? Will i save more oil by fixing it ? :)
@insdel11
11 жыл бұрын
How to amplify and reduce oil flow ?
@gazmtg
8 жыл бұрын
A working oil metering pump is more economical and provides far more consistent oiling for the engine's needs at any given lube point. I.e with premix to have enough oil for max power you'll have enough oil to foul your plug at low load and vice versa. Lean enough to not foul at idle is too lean for max power.
@benives2915
7 жыл бұрын
hi i just found very small bits of metal in my 2 stroke oil Reservoir. anyone got any info please
@taki5baj
7 жыл бұрын
how can i bleed the oil pump?
@hakkedupeiling
13 жыл бұрын
i got a 06 mod myself. with FP exhaust, powerfilter, exhaust valve removed and Cdi removed. with fp + rave i know the oil pump should be set to line against line on the pump, but how do you recommend to set it on mine?
@junrurugeno
11 жыл бұрын
i have a lot of air in my oil tube so what should i do? husqvarna sm 125
@garytauber430
6 жыл бұрын
do you use cheap oil?
@baseemalsharabi2404
6 жыл бұрын
What type of oil is used?
@JH1200A1
2 жыл бұрын
Actually if the engine was ran with the correct settings at the oil pump, as low as that engine was idling, you wouldn't need any pre-mix. Straight gas is fine. Check out "Oil Migration"
@adamcarroll2366
2 жыл бұрын
Thank you.
@ClutchFirstPhilippines
7 жыл бұрын
nice! great video. i noticed when it idles the oil doesnt move at all. can you explain that and is it safe, my friend? thanks!
@giwtwm
7 жыл бұрын
at idle gasoline has enough lubrication to lubricate the conrod without the help of 2T oil
@zfloz9895
4 жыл бұрын
This pump is also helped by the vacuum created in the manifold, where is placed. So what you see in here, it will actually be much faster as a flow ,when the small hose it is in his place.
@adambuster
4 жыл бұрын
How can i disable fully the Oil pump? Can i just unattach the bowden, or just remove the whole pump, maybe plug the oil tube? If i remove the pump, do i need to make a new bowden, or i can let it be there?:D I want to go with premix.
@splatharackal1337
3 жыл бұрын
Premix 2T oil@ 5% of petrol ,(or gas), do it and protect our beloved 2Stroke bikes. ...ck the bloody oil pump.
@jamesmac2513
2 жыл бұрын
Loop the hose from carb to inlet of pump and oil will continue to flow lubricating the pump
@turbinebass
8 жыл бұрын
How working rs 125 with same oil ratio when change 28 to34 mm carburetor? 28mm low fuel 34mm high fuel...
@gazmtg
8 жыл бұрын
When you go to the 34mm carb you need to wind on a lot more preload. I found out the hard way.
@turbinebass
8 жыл бұрын
+CrashDumy Sorry i dont understand, whats mean wind?Like go fast or you said about preload fuel and oil?
@gazmtg
8 жыл бұрын
+turbinebass Sorry auto correct fail. You need to adjust so the cable is pulling on the oil pump pulley a little more. I think I ended up adjusting mine so it had about 1.5mm past the reference mark.
@turbinebass
8 жыл бұрын
+CrashDumy Thanks mate, I already did it, and I add a little oil full fuel tank.
@turbinebass
8 жыл бұрын
+CrashDumy I think your engine is rotax 123 is it right?
@mb125hh
6 жыл бұрын
Looks like you are using cheap oil there. Always use full synthetic with nikasil barrels.
@steamfrog
13 жыл бұрын
were u running premix to test this? Is the oil flow u got there right? Im trying to rebuild mine so thanks for the great videos.
@williamhallock5140
6 жыл бұрын
steamfrog is it ok to pre-mix a two stroke moped, I have a 2004 vento turbocam
@marekczarek5987
3 жыл бұрын
So its work good?
@gazmtg
3 жыл бұрын
Yes. Sure did. You can see on the video it pulses the oil slowly at idle and closed throttle. Then I simulate full throttle and you can see the oil flows rapidly.
@Aviator168
8 жыл бұрын
Oops. You just the killed the engine.
@gazmtg
8 жыл бұрын
No I didn't. The engine was running on premix.
@Aviator168
8 жыл бұрын
OK.
@vinm300
2 жыл бұрын
Very revealing : it hardly uses any at idle.
@splatharackal1337
3 жыл бұрын
Mix the oil in gas tank, .. solved simply
@gazmtg
3 жыл бұрын
Doing that is effective at ensuring lubrication and emptying the wallet when the stuff is over $30 a litre.
@jamesmac2513
2 жыл бұрын
@@gazmtg if going premix what ratio? Is it 50:1 for stock 50cc bike ?
@josephlacour9012
Жыл бұрын
So no verdict? Thanks
@gazmtg
Жыл бұрын
It worked as intended
@josephlacour9012
Жыл бұрын
@@gazmtg it sure didn't look like it was working to me
@gazmtg
Жыл бұрын
@@josephlacour9012 look closer. You can see the oil pumping through the hose when I throttle the pump up.
@josephlacour9012
Жыл бұрын
@@gazmtg It looks like it should send way more oil than that to me! That sucks idk
@gazmtg
Жыл бұрын
@@josephlacour9012 It really doesn't need to send any more. Remember. The RS125 runs a oil mix ratio of between 1 - 3%. That's 100:1 - 33:1. It's injecting 1ml of oil for 100ml of fuel. Just how fast do you think that should be pumping at idle ? You can see when I crank the throttle up on the pump fully it pumps fast. WAY too fast. It's working.
@-M-511
3 жыл бұрын
But in ideling the Engien needs oil too...that seems not right..
Пікірлер: 49