Why does it not tell you which way to insert the roof perlin? OMG we had all that up and went to install the roof but nope, none of the holes lined up!!! Pain in the butt, as we had to take them out and put in again. It doesn't show either on the paper directions.. they should have a side picture showing what the screw holes look like when put in the correct position. And would love if mine had that nice roof support in the middle attaching to the side walls.
@fillusjesus
2 жыл бұрын
Hmmm, I am getting ready to put one together next week, so do you have a suggestion how I might avoid what you experienced? I reread your comment and by chance is there a way to figure out the correct position of the roof Perl before installing? Thanks.
@tanyapatrick9416
2 жыл бұрын
@@fillusjesus the 2 center support beams hang with large holes on the inside. And the roof pieces are what attach to the small holes on that beam
@fillusjesus
2 жыл бұрын
Thank you!
@tanyapatrick9416
2 жыл бұрын
@@fillusjesus I meant to say that it is the very top piece of the roof that screws into all the holes on the center bars. We first thought that the first 2 roof pieces were supposed to screw into all the holes and it would not line up at all but then we looked at the last top roof piece and then were able to figure it out. There are these pulley things that synch that part down and then it is easy to screw in all the bolts. Hint... if you have a magnetic screwdriver you will want to use it. Not the magnetic grabber as it is too wide to put in the holes to pick up any dropped screws.
@tubergenmotorsports4193
3 жыл бұрын
My top roof pice eventually cracked on the cheap bendy seam. So yes it leaks now, right where I don't want it to. "On very top." I'm thinking aluminum flashing, that will certainly look good,,, NOT.
@fillusjesus
2 жыл бұрын
Thanks for sharing. Might I suggest getting some Flex tape to run along the top seam. Because that was an issue for you, I will be proactive and tape the seam before attaching it.
@solidus1010
2 жыл бұрын
Just add a 6” weatherproof tape.
@ImDaBadGuy
Жыл бұрын
Same here. Cracked and started letting water in. Even without a receipt rubbermaid sent me a new roof piece since this shed has a 10 year warranty. Think I will flex tape the seam beforehand this time.
@at39degrees
2 жыл бұрын
Get the plastic windows warm inside before trying to take that protective paper off. Use a magnetic bit holder to hold those screws if you have one. I had to clamp the center roof section with large vicegrips on the outer edge to keep it together so I could get some screws in from the inside.
@grod805
3 жыл бұрын
This is a lot harder than it looks
@tanyapatrick9416
3 жыл бұрын
Great 😬
@ImDaBadGuy
Жыл бұрын
This shed eventually cracks at every seem that you have to bend. All four corners and the peak of the roof, which sucks because you don't notice until it rains one day and everything is wet. I will give the company's customer service a boost though. They sent me a new roof peak and any other parts I needed that failed. Even without a receipt they honor the 10 year warranty.
@GavriloPewPew
3 жыл бұрын
What model #is this?
@tanyapatrick9416
2 жыл бұрын
7x7 Big Max Rubbermaid Shed
@ImDaBadGuy
Жыл бұрын
Model #2035893 Rubbermaid Roughneck 7x7 resin storage shed. I know this comment is old, just in case anyone else needs it
@calvinhubbard7571
3 жыл бұрын
No
@herbiehusker1889
5 жыл бұрын
Thanks for uploading this. I'm going to assemble this tomorrow.
Пікірлер: 18