I always marvel at guys who can cut accurate 45 degree angles free hand..
@AModernMaker
6 жыл бұрын
Thanks! I’m definitely not the greatest though...
@cddc9310
4 жыл бұрын
At least the Lady is still presenting herself in an attractive manner.
@AModernMaker
4 жыл бұрын
Thanks, I’ll let her know
@californiadaze
Жыл бұрын
man, that looks great!!!
@philortega4139
4 жыл бұрын
Love the gate - simple design but attractive and will last. Thanks for sharing. I’m off to build something similar.
@AModernMaker
4 жыл бұрын
Thank you Phil!
@nathanjohansen7169
8 жыл бұрын
4:36 - Put her in the thumbnail and you'll triple your views! That was a nice build too. Loved your plasma "drill".
@AModernMaker
8 жыл бұрын
Haha she loved that! +Nathan Johansen Thanks!
@anhvu9585
8 жыл бұрын
Hai xuân hình than thanh hiện
@gregorycecchin9816
7 жыл бұрын
una bella ragazza :)
@AModernMaker
7 жыл бұрын
+Gregory Cecchin Thanks!
@eventosticra5317
6 жыл бұрын
Really gorgeous! Sexy legs btw!
@agustinavecilla4346
7 жыл бұрын
Nice and clean looking gate.
@AModernMaker
7 жыл бұрын
+Nitsuga Alliceva Very kind of you. Thank you!
@benjaminbutton2897
7 жыл бұрын
Nice effort man. You should have welded a square tube mid rail to help brace it. As you hadn't, you would have been better installing the wood with the gates on your table, that would have helped with sag as the wood would help brace it. Also, don't fully weld a corner without tacking the whole frame together, otherwise you'll struggle to keep the gate square. Nice tools too
@AModernMaker
7 жыл бұрын
Thanks for the tips +Benjamin Button!
@ScottTurnerformeindustrious
8 жыл бұрын
Nice job!
@AModernMaker
8 жыл бұрын
+Scott Turner Thanks, always nice to hear!
@radobaviga4487
5 жыл бұрын
simple and nice
@AModernMaker
4 жыл бұрын
Thank you!
@shachardamari7550
4 жыл бұрын
very professional! Thank YOU! LIKE! LIKE LIKE!
@AModernMaker
4 жыл бұрын
Thanks!
@christianlomeli1631
Ай бұрын
What type of nails did you use to tighten the wood to the flat bar?
@MrTroyocfa
7 жыл бұрын
Nice job man.
@AModernMaker
7 жыл бұрын
+Troy Hoggard Thank you very much.
@davidg5290
5 жыл бұрын
Very nice. If I only had the tools...
@AModernMaker
4 жыл бұрын
Start slowly acquiring tools..
@SUHABOUT
5 жыл бұрын
The gate looks BEA-UTIFUL!!!
@AModernMaker
5 жыл бұрын
Thank you!
@8fivezero
4 жыл бұрын
Very nice job. Well planned out. Looks like you have all the good tools. I especially appreciate you listing the tools and accessories.
@AModernMaker
4 жыл бұрын
Thanks! Glad you liked it. I’ve got a lot of the tools but not the set up to really streamline the process.
@TheSib
6 жыл бұрын
Beautiful gates! Now all you have to do is knock down the entire fence and do it to that. Easy peasy.
@AModernMaker
6 жыл бұрын
Thank you!
@CR-tm5ug
5 жыл бұрын
Good job dear
@AModernMaker
5 жыл бұрын
Thank you
@ranchooper
6 жыл бұрын
Good Work
@AModernMaker
6 жыл бұрын
Thank you
@ranchooper
6 жыл бұрын
as youre welcome....
@romannerush1830
6 жыл бұрын
Good gate!!! 👍👍👍
@AModernMaker
6 жыл бұрын
Thank you!
@Yudiyudi-ez4xu
5 жыл бұрын
good job..👍
@AModernMaker
5 жыл бұрын
Thank you
@homeenforcer
5 жыл бұрын
Very nicely done. Can you give an estimate of material costs? I’m trying to decide if it’s less expensive to build than to buy. Thank you.
@AModernMaker
5 жыл бұрын
Definitely less to build than to buy. My guess is it cost around $100 to build.
@homeenforcer
5 жыл бұрын
A Modern Maker awesome. Thank you.
@AModernMaker
5 жыл бұрын
No problem. I have another video where I build a wrought iron (steel) gate. Materials were $650 and quotes he got from gate fabricators ranged from $3000-4,000.
@genius-no5sl
6 жыл бұрын
Nice work
@AModernMaker
6 жыл бұрын
Thank you.
@DSRCHANNEL
4 жыл бұрын
Luar biasa 👏👏 i like
@AModernMaker
4 жыл бұрын
Thank you!
@garydrysol1550
6 жыл бұрын
Two questions: why the 45 angle on the corners, is that for stability or aesthetics? Also what size are the screws holding the wood to the panels, They look like 1/2 inch panels and wondering if a 1/2 screw will hold it together. But it all looks awesome.
@AModernMaker
6 жыл бұрын
45’s are for aesthetics. Screws were 5/8” I believe and they’ve been holding up well so far. Thanks!
@edouardgluck9588
3 жыл бұрын
People who don’t understand what fabricating for major clients requires “love this video” because of the artistic components which makes sense- and don’t see the CRITICAL flaw early on that in this case didn’t really matter, but it sends a horrible message to young or inexperienced welders/builders that could absolutely cause a major problem if you were building with HSS (it’s not called “square tube” btw...it’s called Hollow Structural Section) larger than the 2” in this video. YOU MUST ALWAYS MEASURE THE CORNER TO CORNER DISTANCE TO CHECK FOR SQUARE BEFORE WELDING THE FLAT SIDES OF THE FRAME. AT NO TIME SHOULD ANY PART OF THE FRAME BE MOVED FRON THE MECHANICAL ATTACHMENT UNTIL ALL SIDES ARE VERIFIED AND TACKED ON THE 3F and 1F POSITIONS. I have seen THOUSANDS of dollars in material and labor cut apart after a week of welding and fabricating because this simple step was not verified, and caused a deviating of 1/16 of an inch that rejected the part for a major household goods company in Cincinatti, Ohio. This isn’t hating on his video for those who might claim as such- it’s actually highlighting why it’s important for the experienced and skilled to police these forums and give praise where it is proper and revision where required. Nice gate.
@notanymore9471
19 күн бұрын
Actually it is often called “square tubing”. I can go to Industrial metal supply’s website right now and look through their “square tubing” section and not anywhere on their site will it be called “hollow structural section”. In fact in 27 years of manufacturing I have never seen that term used. “Square tubing” and “rectangular tubing “ are common terms used in industry.
@edouardgluck9588
15 күн бұрын
@@notanymore9471 Thanks for your insights and sharing about your experiences. You have never seen this term most likely, because you probably have not participated in the design and blueprinting for manufactured large scale steel structures such as bridges or aerospace components. The term “Square tube” is not indicated nor recognized language on properly formatted AISC, and ASME P.E. approved drawings. Have a great weekend.
@notanymore9471
15 күн бұрын
@@edouardgluck9588 and it’s used in industry all the time. The guy was building a gate not an aerospace product nor a bridge nor anything pertaining to ASME or AISC. The industry doesn’t speak “conceited engineer”.
@Clemilsonccs
8 жыл бұрын
Good job! 👍
@AModernMaker
8 жыл бұрын
Thank you! +Clemilsonccs
@mattier3030
4 жыл бұрын
Also i m a wood worker who would love to learn more welding, I have very limited metal work. I would have made costume tongue and groove floating panels...
@AModernMaker
4 жыл бұрын
I'm sure that would look great, but would be way more work than I wanted to put into a gate for chickens.
@craynerd
5 жыл бұрын
Excellent. How did you attach the wooden timbers? I can see they are being held but I’m not totally clear how!
@AModernMaker
4 жыл бұрын
Just with screws.
@craynerd
4 жыл бұрын
A Modern Maker haha thanks. A 9 month wait but worth it :-)
@AModernMaker
4 жыл бұрын
Sorry about that 😬
@JoseAlejandroSanchezBaca-vg6hu
Жыл бұрын
What type of wood did u used?
@jackhammer8364
4 жыл бұрын
Vinegar and wool will give you that stain,I'm comfused?
@-hexmode-6417
3 жыл бұрын
Can a beginner do this if I learn how to weld?
@MotherAmerica-ci1uu
5 жыл бұрын
Best video 🔥🔥🔥. Make more
@AModernMaker
5 жыл бұрын
Thank you Jesse!
@brendacerdabravo9606
5 жыл бұрын
Hola,me encantó éste trabajo,es justo lo que necesito para mi patio.Quiero saber que tipo de tornillo usaste para afirmar las tablas.Tengo mi reja de metal que dá a la calle con madera, pero la llenaron de tornillos 🤦 Saludos desde Chile 🇨🇱
@AModernMaker
4 жыл бұрын
Use tornillos para sheet metal, pero puedes usar qualquier tornillos si caben.
@MetalFaceLoofah
3 жыл бұрын
Hey What is the steel size and thickness? It's called HSS or RSS correct? I'm wanting to use your dea and build to 7ft panels for my driveway gate. Any suggestions? ......
@AModernMaker
3 жыл бұрын
I can’t remember. Either 2x2 or 1.5x1.5. Thickness was .120” I believe. But for fence you could go thinner walled. And it’s just mild steel.
@MetalFaceLoofah
3 жыл бұрын
@@AModernMaker I see. I'm thinking about using the method to build a 14ft car-gate. (2) 7'x5' panels and attaching them with cattle gate hinges to 6x6 Cedar posts that are already installed.
@AModernMaker
3 жыл бұрын
That’ll be nice.
@mlungiseleliwexu8772
7 жыл бұрын
Awesome.
@israelcastellon4478
Жыл бұрын
What size of metal did you use.
@wesleycain8203
2 жыл бұрын
What size metal pieces did you use?
@sajjanKumar-eg7mu
4 жыл бұрын
Hi bro I m from india and I want to built this type gate.will it be safe in rainy season and wt camical can we use to protect from sun light and rain.
@AModernMaker
4 жыл бұрын
Hey. Yeah just make sure you have a good clear coat on the metal and some sort of water seal on the wood.
@erichaltomwoodworking7363
8 жыл бұрын
That turned out great, nice job... now for the chicken wire fence next to it?
@AModernMaker
8 жыл бұрын
Thanks! Yeah... That is very low on the priority list but it does need to get done! Hopefully soon.
@erichaltomwoodworking7363
8 жыл бұрын
I know what you mean. I'm always 10 tasks behind.
@AModernMaker
8 жыл бұрын
Same here +Jack Of All And I've got a wedding coming up in a couple weeks and still have a ton of stuff to build for it!
@larrywoodward6564
4 жыл бұрын
great work. love the detailed view, and your attention to detail. Im looking to replace my old broken wooden 11' gate, in phoenix, az, usa. Any chance you got time for me?
@AModernMaker
4 жыл бұрын
Thank you! I wish I could but I have zero time available right now...
@randydavis8064
8 жыл бұрын
What "Patina Stain" did you use? I like the way it turned out. Great job!
@AModernMaker
8 жыл бұрын
+Randy Davis Thanks Randy! It's called Black Magic by Sculpt Nouveau.
@randydavis8064
8 жыл бұрын
Will have to give that a try!
@AModernMaker
8 жыл бұрын
+Randy Davis If you have any question, let me know!
@Bootzey73
7 жыл бұрын
Randy Davis
@Josh-gb6mv
7 жыл бұрын
I've seen where you can buy a DIY kit at a gunstore to re-blue an old gun, have you ever tried it on structural steel? I wonder how it would look.
@AModernMaker
7 жыл бұрын
+Xrated Rednek I've never tried it, but I'm sure it could give a similar look. They sell it where I buy my metal treatment product. Maybe I'll try it out sometime!
@joshsaavedra6193
3 жыл бұрын
What size screws did you use?
@AModernMaker
3 жыл бұрын
5/8”
@lorenzobustos1253
6 жыл бұрын
Great work! What kind of wood sealer did you use?
@AModernMaker
6 жыл бұрын
Thank you! It was Thompson’s wood sealer. Still holding up well.
@BestAccessDoors
7 жыл бұрын
Fantastic work! Are you going to do more videos like this soon?
@AModernMaker
7 жыл бұрын
+Best Access Doors Thank you! Hopefully in the near future!
@stevendouglas3860
4 жыл бұрын
How much would it cost .63" x 54" fence
@AModernMaker
4 жыл бұрын
No idea. I typically don’t build to sell.
@stevendouglas3860
4 жыл бұрын
@@AModernMaker okay. Lovely neat work ..may I say sir
@princeedakota9357
4 жыл бұрын
Hi, what type of wood and thickness did you use? Thnx
@AModernMaker
4 жыл бұрын
Cedar planks, about 5/8" thick
@JoaoVictor-gp3hl
4 жыл бұрын
What kind of wood is that?
@AModernMaker
4 жыл бұрын
Cedar
@collindainphillip3116
5 жыл бұрын
What size RHS was used to frame the gate?
@AModernMaker
4 жыл бұрын
1.5"
@JUNIOR-mi2ei
5 жыл бұрын
What side of tubing u are using???
@AModernMaker
5 жыл бұрын
1.5” I believe
@CazaPutas-in9vn
7 жыл бұрын
Kiko dice: uyy así que fácil.
@icarrrv
6 жыл бұрын
Good job but safety first
@kojomensah7474
7 жыл бұрын
If u do I would like to have the plans pls
@AModernMaker
7 жыл бұрын
+keith henry Definitely
@SuperNorthsea
4 жыл бұрын
I would like to get the type/size of metals used along with the plans. It turned really great. I just bought my first welder and would like to try this project.Thanks jamie
@madnalab3901
4 жыл бұрын
MAMASITAAAA..........xoxoxox. jk. great job
@AModernMaker
4 жыл бұрын
Thanks!
@antonelladivannidibiaggio7684
6 жыл бұрын
MUY BONITA TE HA QUEDADO ESA CERCA PARA QUE TUS GALLINAS NO ESCAPEN DE TU SITIO. PREGUNTA: QUE ES DE TU PERSONA ESA MUJER QUE SE VE EN LOS VIDEOS, CUAL ES TU NOMBRE Y TU EDAD ES? . TE LO PREGUNTO DESDE CHILE....BIANCA ANTONELLA DI VANNI DI BIAGGIO, EDAD 27, SIN HIJOS, SIN NOVIO, SIN AMANTES Y AUN NO HE SIDO CASADA
@josemelendez1487
3 жыл бұрын
mui guapa des de México
@pedroaraya4061
4 жыл бұрын
le pone mucho color a la wea ajajajajasj
@conqueringlion420
6 ай бұрын
Looks cheap
@DeBildr
5 жыл бұрын
No.....i like mine better
@luismejia5448
2 жыл бұрын
What sizes for metal did you use?
@sergiofierro82
5 жыл бұрын
Lo.mejor del video es la rica mujer que se ve.
@AModernMaker
4 жыл бұрын
Thank you!!!
@fedymyr
4 жыл бұрын
No hay nada mejor que poseer absolutamente todas las herramientas adecuadas!
@AModernMaker
4 жыл бұрын
Thank you!
@Jeffhuebner
8 жыл бұрын
Badass gate! Nice work!
@AModernMaker
8 жыл бұрын
Thanks Jeff!
@ikazuchisama
5 жыл бұрын
The step at the foot is dangerous
@timothyjohn3006
Жыл бұрын
Just come across the video, very impressive gates, that looks quite easy make! Hopefully any way. 😁👍
@walkr7998
5 жыл бұрын
I'm trying to replace the wood on a driveway gate that's made just like this. What kind of wood did you use or would you recommend that I buy? I've never really worked with fencing like this so I'd appreciate any tips on what I should be asking for at the lumber yard. I'm going to have to get it cut there too. Great job with this video, thanks.
@AModernMaker
5 жыл бұрын
I used cedar planks. Holds up well to weather and bugs. Redwood should be good too.
@alphasigmasezon8597
5 жыл бұрын
Excelente serviço.
@sergeystrizheus3368
6 жыл бұрын
No fence just gate 😂
@Engel-re4bp
4 жыл бұрын
Congratulations. Very good.
@AModernMaker
4 жыл бұрын
Thanks!
@arnoldorobles4661
2 жыл бұрын
Cuánto sale costo
@laurentiuiordan1908
2 жыл бұрын
Can you please tell diameters for square bars..thanks
@michaelw2108
3 жыл бұрын
Nice gate. Can I use an angle grinder to cut the thin strips of metal
@XDaA-oo7pd
7 жыл бұрын
What size wire did u used? What machine is that? Gas? Ect...? Thanks man
@AModernMaker
7 жыл бұрын
+X2DaA 503 I think it was .035, Lincoln 210 MP, CO2/Argon gas mix.
@TheSib
6 жыл бұрын
size: 128375638359322090.2 machine: *%$@ Gas: Gross - Grow up man.
@werillosanchez2883
4 жыл бұрын
Fabricare una igual aver como me queda
@AModernMaker
4 жыл бұрын
Mandeme una pic cuando la termine.
@werillosanchez2883
4 жыл бұрын
Ok
@jscarter0110
5 жыл бұрын
I noticed that you have a plasma cutter (I want to get one soon too). Why do you not use it to cut your angles instead of the bandsaw? Are the cuts too sloppy with a plasma cutter? Awesome build btw!!!
@AModernMaker
5 жыл бұрын
Thank you! I used square tubing which is faster to cut with a bandsaw. With a plasma cutter I’d have to cut all 4 sides.
@roycekirk8428
3 жыл бұрын
Whats your welder wire feed and voltage set at?
@Santamonicadrainco
6 жыл бұрын
Thanks for sharing and making it look so easy. I’ve built wooden gates my whole life and I just started incorporating metal into my woodworking shop. Your super easy to follow and watch. Just subscribed!!
@AModernMaker
6 жыл бұрын
Thank you! I think you’ll love adding some metal in with the wood, I know I sure do!
@nayefalkurahi3357
7 ай бұрын
I can smell the welding lol
@larrynavarro6691
7 жыл бұрын
You are one great handyman great job brother God bless.
@AModernMaker
7 жыл бұрын
Thank you +larry navarro !
@BrianBoruish
4 жыл бұрын
Great video. What do you all use to prevent a steel gate from rusting? I was thinking of powder coating mine after I weld it up. Any better suggestions?
@AModernMaker
4 жыл бұрын
Powder coat or plan on painting periodically. I don’t mind the rust though for that gate.
@basuramanya
8 жыл бұрын
Chickens were giving you the stink eye at the end as you were walking out. Nice looking fence.
@AModernMaker
8 жыл бұрын
Thanks Dan. Haha, yes they were... They want FREEDOOOOM!!
@gilbertmatty5654
7 жыл бұрын
that's exactly what I need only I'm making it 92 inches tall with a crossbeam for added support. my only question is I don't have concrete slab, I was wondering if I could set post on ground with concrete mix. or should I set a it attached to a footing?
@AModernMaker
7 жыл бұрын
+Gilbert Matty It should be fine if you set the post nice and deep. Are you going to add a wheel on the long side?
@markman63
3 жыл бұрын
what type of wood is this?
@harry18597
4 жыл бұрын
Nice... did you used a stainless tubular or galvanised one? and also the flat bar?
@AModernMaker
4 жыл бұрын
Just painted mild steel
@Growingwiser550
6 жыл бұрын
flippin awesome job bro.
@AModernMaker
6 жыл бұрын
Thanks Growingwiser
@andresgomez9533
4 жыл бұрын
What is the size and kind of wood you used for the frame? Tanks my brother
@AModernMaker
4 жыл бұрын
Standard fence pickets. 5/8” thick, ripped to appropriate width and cut to height.
@chrispatton2111
6 жыл бұрын
Love the video and gate! Question...how wide was your opening and how wide was your gate you built? I'm building one soon and would like to know the space you left on the ends for the hinges.
@AModernMaker
6 жыл бұрын
Thank you! The gate was 9 feet wide total. 1/4” gap between and about 2” on each side.
@gradeez
8 жыл бұрын
Love it!! That's one badass gate for chicken! hahahaaha!
@AModernMaker
8 жыл бұрын
+gradeez Thanks! Maybe just a little overkill... haha!
@manuelgarduno6850
6 жыл бұрын
En el minuto 2:20, perforas metal, que máquina utilizas y hasta que grosor puede perforar, saludos.
@elmeromero2500
6 жыл бұрын
Manuel Garduño Es una cortadora plasma, no es real mente para perforar aunque en metal delgado si lo puedes hacer, es mas bien para cortar metal y depende de la capacidad de maquina para el gruesor, he visto algunas que cortan placa de hasta 1 pulgada de gruesor.
@AModernMaker
6 жыл бұрын
Hypertherm Plasma Cutter. Puede perforar hasta media pulgada.
@GB-ARG
8 жыл бұрын
Nice job my friend, I wanted to ask about the black patina for metal, is your formula or commercial sale? Thank you very much.-
@AModernMaker
8 жыл бұрын
Thank you +Germán It's a commercial product. Black Magic by Sculpt Nouveau.
@GB-ARG
8 жыл бұрын
Thanks for the quick response, respect from Argentina!
@AModernMaker
8 жыл бұрын
+Germán Anytime. Awesome!
@ma88tc
3 жыл бұрын
Great job man! Real clean job!
@ramp2510
6 жыл бұрын
FELICIDADES MUY BONITO, MI TRABAJO ES DE OTRO TIPO, PERO TAMBIEN ME GUSTA TRABAJAR EN MI CASA Y TRATO DE HACER COSAS, Y AHORA ESTOY TRABAJANDO EN UN PORTON COMO EL DE UD.
@AModernMaker
6 жыл бұрын
Gracias. Buena suerte!
@arnoldorobles4661
2 жыл бұрын
Cuánto salio todo
@joeferrucci
5 жыл бұрын
What is the size and kind of metal you used for the frame?
@AModernMaker
5 жыл бұрын
1-1/2” mild steel tubing
@jesushuerta3838
2 жыл бұрын
qqqa
@elsirolchicho1571
6 жыл бұрын
wow tenkiu eees grande
@maherajah9713
6 жыл бұрын
What size tubing did you use for the frame?
@AModernMaker
6 жыл бұрын
1.5” I believe
@MusikaHouse
7 жыл бұрын
Great build! how much gap did you leave between the wood? stay awesome
@AModernMaker
7 жыл бұрын
+MusikaHouse Thank you! About 3/16"
@AModernMaker
7 жыл бұрын
+MusikaHouse Possibly 1/8" can't remember...
@TheManishpandey007
6 жыл бұрын
wooden gates dint get wet in rainy seasion???????
@AModernMaker
6 жыл бұрын
It got a little wet but it’s holding up well!
@jayaseto
5 жыл бұрын
Hi, pls what type of wood did you use?
@AModernMaker
5 жыл бұрын
It was cedar
@jayaseto
5 жыл бұрын
Thanks
@Bullet_sHouse
4 жыл бұрын
Great work looks good
@AModernMaker
4 жыл бұрын
Thanks 👍
@saljudeh
7 жыл бұрын
where do you get these large metal fence posts
@AModernMaker
7 жыл бұрын
+Abu Kareem At a metal supply yard/retailer, or you can buy them online.
Пікірлер: 225