I use to hate electronics but in the last decade I have found it so interesting. Great video!!
@wa6ati
6 жыл бұрын
Cool Mike. Love it. This Hall sensor is also used on the flow control in the dishwasher case break. It too is latching type as you indicated here.DV
@electronicsprojects4708
6 жыл бұрын
Thanks, Dennis
@mouradmourad832
Жыл бұрын
Good video mr if you have the reference of 2 hall effect sensor i would be so thinkfull
@MrHgsherrard
2 жыл бұрын
Is this universal for all Samsung Washing machines? My part is slightly different in shape, but it's definitely a similar platform. Mine is a top loading washer. Part number DC31-00153A.
@georgecass8529
2 жыл бұрын
So where is the Hall Search your located at on the washer
@okwestern
4 жыл бұрын
You don't happen to know which hall sensors they are? I'm guessing 61A or 66A since they are latching.
@electronicsprojects4708
4 жыл бұрын
I could not identify them when I made the video, unfortunately. As I recall, I attempted to look for the datasheet.
@Gacha.Cupcake
Жыл бұрын
What is the hall sensor model number? The actual chip Thanks
@electronicsprojects4708
Жыл бұрын
I don't have it for this one, but the hall sensor was from an LG top load washer stator.
@garybarbourii8274
6 жыл бұрын
What voltage do the sensors latch to? I'm getting just under 1.2V each, but they are still attached to the main control board. I'm about to pull my scope out and look for broken magnets in the motor. Unfortunately I only have one lead for my scope right now but I don't think that should be too important
@electronicsprojects4708
6 жыл бұрын
5vdc
@garybarbourii8274
6 жыл бұрын
@@electronicsprojects4708 thank you for the reply! After replacing my main control board, twice, my problem was solved. The supposedly new from floor model control board I had ordered the first time was also bad, sending me on quite the goose chase. But the washer runs great now!
@sevillasllc3391
2 жыл бұрын
Gary, hopefully you remember but what error code(s) and symptoms were you having with your washer to determine to swap the control board?
@washerdryeradvicechannel8041
2 жыл бұрын
@@sevillasllc3391 the control board hardly goes bad. Unless voltages flashes and control board goes on and off. Hall sensors failure show in a different way. It turn on but the durm spin in a violent way a couple times and then it should show an error
@thienvu4503
5 жыл бұрын
input 5vdc to power which are the color of the 2 wires ? thanks
@electronicsprojects4708
5 жыл бұрын
red is 5vdc, green is ground
@awesomeappliance
7 жыл бұрын
Good video
@oscartenorio4860
7 жыл бұрын
Hola soy de México que valor tiene los triac del sensor
@electronicsprojects4708
7 жыл бұрын
Not sure if my translation is correct, but there are no Trials in the sensor circuit. Triacs are used to relay AC voltage, like a relay. These Hall effect sensors operate on DC voltage, usually between 5 - 15 VDC depending on the design.
@Spark-Hole
Жыл бұрын
Should have three sensors H1 H2 H3, Why only two.
@electronicsprojects4708
Жыл бұрын
sense direction, clockwise and counter clockwise.
@fredermanrodas
Жыл бұрын
Tan amable referencia voy modelo de los integrados hall
Пікірлер: 23