This $4 part failed on my 2019 SXF-350. I had 8 hours on the engine. I lost the crank, crank bearings, piston, rings, cylinder, and head.... i.e. my motor was turned to scap. There's no warning that the fail is coming. You're fine up until the moment your not. Change this part!!!
@dirtbiketv1
3 жыл бұрын
That sucks--
@2wheels_and_2stroke
3 жыл бұрын
Just done mine today and I have 200 hours on the original one and it's still like new but I changed it for the new part anyway
@travisconover4762
11 ай бұрын
This is complete madness I'm starting to hate this bike
@Rayzer1989
2 ай бұрын
Ktm.... Keep Taking Money
@TepcoCycleRepair
3 жыл бұрын
You can tell Brad knows his stuff, he just takes things off and throws them in a pile because he knows exactly how they go back on. Thumbs up for awesome mechanics!
@zrkn1
4 жыл бұрын
Expert tips are much appreciated and needed. Thank You! This could save someone big bucks for a $30 fix.
@MrXiztence
3 жыл бұрын
I got lucky and caught this by finding little black plastic during my oil change on my sxf 250 2018. It wasn’t completely failed but the teeth on the gear were starting to break apart. Wish I had seen this before :) Great video
@btodal6504
Жыл бұрын
How many hours did u have when this started to happen
@bryny6691
Жыл бұрын
Mine is the same ordered a metal gear, was there any damage to your cams ? Or did you get away with it ? I’m hoping I did but will check to make sure when I install the new gear
@ethemwybrow794
2 жыл бұрын
Old is PA6 (nylon) compared to new is PA66 GF30 (30% glass filled nylon)
@richielee5398
Жыл бұрын
Be very interesting to know how many KTM and husqvarnas have seized in total. Must be 100s and 100s mine went at 102 hrs. KTM should have done a recall on the part. They knew it was faulty hence the new part. I know of at least 8 bikes just in South Wales that this gear has killed.
@noControl556
4 жыл бұрын
Just seems like if you are going to upgrade a failed plastic gear, you would want to put a metal one in there
@Papparratzi
2 жыл бұрын
Exactly, that’s what I did. The updated plastic gear must be doing good. Haven’t heard of the failures like I used too. The guy that made mine says, it’s actually the little one that takes out the big one. His kit includes both.
@rboote7232
3 жыл бұрын
Good vid. My 2017 ktm 350 xcf broke this plastic gear at 30 hours..... had to rebuild the whole motor, all parts except the casings. If you own a bike with this older plastic gear, change it ASAP or expect a $8,000 bill (poss 4k USA) im in NZ. Its a KTM manufacturer fault and there was no recall as far as I know, amfrom what I read, they may have not mentioned it to avoid payouts....... just me speculating tho. :)
@jonphotos8631
4 жыл бұрын
Looks like the new one would also b breaking at some point
@LukeBrinkerhoff
3 жыл бұрын
only 17-19? I have a 16, I checked the gear, it looks brand new. 160 hours.
@christinedoughertyrealtor9601
2 жыл бұрын
my 16 had the old gear that should be replaced
@michelmartin4151
4 жыл бұрын
This advice is gold , Thank you !
@dirtbiketv1
4 жыл бұрын
Glad it was helpful!
@eugendanciu9789
3 ай бұрын
Hello! At how many operating hours should the pinions be changed?, thank you!
@dirtbiketv1
3 ай бұрын
Email Jay with any questions. Contact info in About tab.
@fsubulldog03
4 жыл бұрын
Thanks for the vid Jay! I was under the impression it only affected 2016-17. Now I gotta crack mine open. I like your mic holder, with 3 daughters I have several pink ones laying around the house lol
@MrXiztence
3 жыл бұрын
It broke apart on my 2018 well semi broke apart.
@fsubulldog03
3 жыл бұрын
@@MrXiztence I replaced mine a few months ago just in case.
@sparker245
4 жыл бұрын
There have been incidents of the updated gear failing as well, but not nearly as often. So it's not a guaranteed 100% fix, but absolutely worth doing.
@matjazkrizman86
3 жыл бұрын
If this problem is simmilar to all ktm/husa engines, why were there no recalls from ktm factory? I belive you, but still... That kind of technical flaw should be noticed by them. And i hope KTM wouldnt simply ignore that. Yes?
@woollywhippet9899
3 жыл бұрын
I believe the problem is more to do with oil pressure control and poor design of the relief port. Depending on how the relief valve has been fitted with its spring.... when the ball is pushed off its seat it can partially cover the port back to the suction side of the pump... you then get a pressure build up that causes a strain on the pump drive..... hence the weakest link fails...that’s why we still see failures with the new gear too....on testing pressures it should be 13 psi at 1600 rpm and 36 psi at 6k and I have seen 150-200 psi...get those pressures checked to specifications in the manual and see what KTM have to say about it.....
@mgruntman
2 жыл бұрын
I wish you would do a video about the oil pressure relief port design problem and fix it would be usefull and interesting?
@dirtrider9268
2 жыл бұрын
Yes, lets see this pressure check process.
@richielee5398
Жыл бұрын
It's the type of plastic it goes soft warps and drops of the side of the other gear more often than shearing teeth off. However sheared teeth would indicate possible high pressures in the system causing teeth to fail.
@andrewmiddlemass
4 жыл бұрын
Why wouldn’t they switch it to a metal gear?
@RottenCottonSheep
3 жыл бұрын
hahaha
@elmerrodriguez9817
3 жыл бұрын
Because they want to make more money when your engine blows up amd you have to buy parts from them
@zeishoot
2 жыл бұрын
CHANGE IT !!! my oil pump just died 3 days ago and it brome everything (crankshaft, piston cylinder and oil pomp are dead)… so change it every 100hours to prevent anything
@alexandre8598
3 жыл бұрын
Why not using steel one?
@paulcombs-dl1jo
3 ай бұрын
what were the symptoms, i think im going through this at the moment, does this include 19 models to?
@AndrerileyLSX
3 жыл бұрын
This video probably saved my engine thank you
@wrenchone5003
3 жыл бұрын
Just looked my 14 has a metal gear so I guess it's just later models ?
@nickdougherty3528
2 жыл бұрын
Anyone know how to watch the tear down in real time? I'd like to the process slower so I can take care of my gear.
@TheJumpn
2 жыл бұрын
This one just came out recently. Shows much more in depth. There are two nuts that are left handed threads (Righty loosey, lefty tighty) that is not mentioned here. kzitem.info/news/bejne/s4pov4CZi350iIo
@TheTT124564
3 жыл бұрын
What tool do u use to pull that primary gear off?
@Bouldertag
2 жыл бұрын
I just found out that mine is warped and that is why it is not running. I have 22 hours on the 2018 350CX-F. If there is piston or any other damage will KTM warranty it? It’s a known issue I would think they would.
@dirtbiketv1
2 жыл бұрын
Email me. Contact info in About tab.
@travisgilliam5
Жыл бұрын
How far back in years does this issue go?
@jimmystevens9028
2 жыл бұрын
Can you do a video on installing 6th gear into ktm\husqy\gasgas. I just came across the new kit from rocky mountain. Yes I know I should have bought an exc. Lol.....I hate having to rev the piss out of my 450 ktm to do 50-60mph down the road. I plated my 450 SXF and put a light kit on it.
@dirtbiketv1
2 жыл бұрын
Email me. Contact info in About tab.
@pasqualemorello3966
10 ай бұрын
Hi, can I ask you what maximum temperature your motorbike reaches in the radiator?
@RevNecks220
4 жыл бұрын
Would there be any benefit to install one of those clutch weights in a 2stroke trail bike?? (Ktm 250 or 300)
@dirtbiketv1
4 жыл бұрын
Yes it can. We don’t usually since so easy to ride anyway.
@addinson01
2 ай бұрын
How much money has this job ? I have a 350 from 2017 👀
@matthewsmith5109
3 жыл бұрын
Thanks guys. Great video 📹
@Stolo17
Жыл бұрын
Are the gears in the 2022 350 excf the new updated parts? Ie.. don't need to replace
@dirtbiketv1
Жыл бұрын
Email Jay directly with any questions. Contact info in About tab.
@SLP-eb1wp
3 жыл бұрын
Has this been rectified in 21/22?
@joebelanger2919
2 жыл бұрын
Do the 2022 SX 350f models have this plastic gear?
@dirtbiketv1
2 жыл бұрын
Yes but its the updated one that we have not seen fail -
@joebelanger2919
2 жыл бұрын
@@dirtbiketv1 it was updated for the 2021 models?
@joebelanger2919
2 жыл бұрын
@@dirtbiketv1 do you know what the update part number is?
@dirtbiketv1
2 жыл бұрын
@@joebelanger2919 The exact time is tough-- some late 2019 are ok -- so 2020 and up are all usually good -- email any other questions - Thanks!
@dirtbiketv1
2 жыл бұрын
@@joebelanger2919 its in the video -- last question on here- email any others -- Thanks
@dirtyoffroader2093
3 жыл бұрын
Do you need a puller to get the primary gear off? Couldn't see in the video. Thanks in advance 👍🏼
@dirtbiketv1
3 жыл бұрын
NO
@dirtyoffroader2093
3 жыл бұрын
@@dirtbiketv1 Thanks again 👍, I'm going to swap mine over tomorrow as a precaution, Although the old idler wheel has done well at 130hrs.
@lunepilot2874
2 жыл бұрын
Do you need to drop the oil to do this, with engine in bike.
@purprea
2 жыл бұрын
tank you ......bravo
@123mykie99
3 жыл бұрын
Odd question but is it required to drain oil?
@joeybishop7604
3 жыл бұрын
Why not put in a steel gear, instead of plastic?
@theplowtruck
3 жыл бұрын
Ok I messed up and didn't lock my engine at TDC- how do I get my timing back to where it should be?
@edwardharding3844
2 жыл бұрын
MY 2017 690 ENDURO R ONLY 4000 CLICKS .. NO OIL PRESSURE AT ALL , REMOVER OIL PRESURE SWITCH , STARTED NO OIL COMING OUT AT ALL..
@kevinrobert3641
3 жыл бұрын
Hi I have a 2014 excf350, we’re the bad gears fitted back then.
@Hondmad
3 жыл бұрын
Is the 2013 affected with this? I really need to know! Thanks
@dirtbiketv1
3 жыл бұрын
No
@lukehighdale725
Жыл бұрын
Why is the 2013 not affected.. is it worth doing just coz?
@dereckrodriguez9688
6 ай бұрын
Will I need to do this if I have a 2020 350excf?
@danblekeberg2470
3 жыл бұрын
Today I called 3 different KTM dealers. They said this has not been a problem ?
@dirtbiketv1
3 жыл бұрын
Yep-- -most won't-- but the few that do its very bad.
@spencerclark2269
4 жыл бұрын
Awesome video that could definitely save my engine. I’ll be sure to check my bikes.
@dirtbiketv1
4 жыл бұрын
Right on!
@spaceboyrr
4 жыл бұрын
Jay, can you not replace the idler gear by just removing the clutch cover and removing the clutch basket? Does the entire side case cover have to be removed to perform this procedure?
@dirtbiketv1
4 жыл бұрын
Have to do all like we did-- big case has to come off-- sorry
@spaceboyrr
4 жыл бұрын
@@dirtbiketv1 Thanks. I changed it out the other day already. It had the old suspect gear but it still looked to be in great shape. No wear on the teeth or warpage to the gear.
@dirtbiketv1
4 жыл бұрын
Bren Lugo ya it will typically look fine until it breaks.
@btodal6504
Жыл бұрын
@@spaceboyrr how many hours did you have
@spaceboyrr
Жыл бұрын
@@btodal6504 That bike had around 200 hours when changed.
@PsyformSamples
Жыл бұрын
Is the 2015 sxf 350 affected by this problem?
@dirtbiketv1
Жыл бұрын
Email Jay with any questions. Contact info in About tab.
@Pedrofs001
4 жыл бұрын
Great tips and video amigo!
@ScramblingLife
2 жыл бұрын
I wonder if oil pump clutch is still an issue for 2022 models? Any idea?
@dirtbiketv1
2 жыл бұрын
No it’s not.
@ScramblingLife
2 жыл бұрын
@@dirtbiketv1 Thanks a lot for your response …
@bossen2436
3 жыл бұрын
Is this for a SXF 350 2019? European if it matters?
@Gabriel19-87
3 жыл бұрын
The Same Problem, You Need Change ;)
@ryanfoster7417
Жыл бұрын
Does the 23 model come with the updated part?
@enduromadness8987
3 жыл бұрын
Do I need to do this on a Ktm 350 excf 2017?
@dirtbiketv1
3 жыл бұрын
yes-- - sorry
@lunepilot2874
3 жыл бұрын
Does this problem apply to 2018 350 SXF.
@dirtbiketv1
3 жыл бұрын
yes
@mxcollin95
Жыл бұрын
Wonder why KTM would choose to run a plastic gear in such an important place?
@harry101fly2
2 жыл бұрын
Is this an issue for 2021 model?
@mikeybstunts
3 жыл бұрын
Anyone know the torque setting for the nut on the gear that has to be moved to get at it
@2wheels_and_2stroke
3 жыл бұрын
100 nm with loctite 243 for the primary drive gear
@mxracingunlimitedltd7784
2 жыл бұрын
So does a 2020 ktm 350 exc-f have this new oil pump gear from the factory? Any reason to swap out the stock one on my 2020 for this new part # gear? Or does it already have it?
@dirtbiketv1
2 жыл бұрын
You can email Jay with questions - can find contact info in the About tab.
@bryny6691
Жыл бұрын
2019 was the last year apparently
@kevscanada4741
3 жыл бұрын
What about a 2013 sxf250?? Thx
@thebuckey6684
2 жыл бұрын
Was the gear changed to the newer one for the 2020 and plus 350s?
@dirtbiketv1
2 жыл бұрын
Yes-
@31nerf
2 жыл бұрын
From which year's bike should owner be concerned?
@dirtbiketv1
2 жыл бұрын
Email Jay directly with any questions. Contact info in About tab.
@Booki89
Жыл бұрын
Anybody know when they fixed this from the factory?
@dirtbiketv1
Жыл бұрын
Email Jay - contact info in About tab.
@dasatom3060
2 жыл бұрын
Hello, in the Sparepartsfinder has the Plastic Gear of my Model already the shown Part number. Does my Model now have the new or the old (bad) one? Thanks ;)
@dirtbiketv1
2 жыл бұрын
Email Jay directly with any questions - contact info in About tab
@mrmoon1482
5 ай бұрын
Peugeot use them plastic cogs in scooter engines, I had a brand new scooter and 2000 miles down the road the oil cog shattered and destroyed the engine within a few seconds, it warped and jammed then shattered, stupid design
@jabariwinters8742
3 жыл бұрын
anyone know if this is apparent in any of the 16 350's? or any year 450s?
@dirtbiketv1
3 жыл бұрын
Yes 16 350 -- not there 16 350EXC-- the others yes-- NO 450's email me if any other questions as I rarely check this--
@jabariwinters8742
3 жыл бұрын
@@dirtbiketv1 shoooot was just about to grab a 16 Thanks for the quick reply! You guys are helping lots of riders out there
@fsubulldog03
3 жыл бұрын
Jay, is that crankshaft gear a LH or RH thread?
@dirtbiketv1
3 жыл бұрын
ummm-- I would see the manual but I dont remember doing any LH when do this--
@jimhull6721
3 жыл бұрын
@@dirtbiketv1 One of the very important details left out of the video.
@fsubulldog03
3 жыл бұрын
@@dirtbiketv1 Just changed it out this weekend. It's LH, the nut has LEFT stamped on it.
@dirtbiketv1
3 жыл бұрын
@@fsubulldog03 Awesome-- I knew it had to be idiot proof for me to not remember it :-)
@Kyle-pl6rl
3 жыл бұрын
I have a 17’ 350 XC-F and I’ve been getting a lot of aluminum in the oil. It sure looks like my balancer shaft has walked out a little bit. Is there any advice on this?
@dirtbiketv1
3 жыл бұрын
We think you need to get the main larger cover off the ride side-- The primary could be loose -- but either way something on that side and need that off to see it-- then take clutch off and see what else could be--
@Kyle-pl6rl
3 жыл бұрын
@@dirtbiketv1 I’ll check the primary gear when I have a chance. The driven balancer gear has moved about 1/8” out. It shows some wear on the face, I’m not sure why yet. Thanks for the reply.
@dirtbiketv1
3 жыл бұрын
@@Kyle-pl6rl You get that cover off and I think you will see why- email me in the future - way better.
@Kyle-pl6rl
3 жыл бұрын
@@dirtbiketv1 Thanks for the help. I’ll email a picture of what I’m seeing.
@2wheels_and_2stroke
2 жыл бұрын
Kyle did you find out what the issue was I'm currently having the same issue with lots of alloy in the oil
@Prestonesfpv
2 жыл бұрын
But what about engines before 2017, are they fine ?
@dirtbiketv1
2 жыл бұрын
email me specific model and question-- link in about etc- Thanks
@claudiocortes4948
3 жыл бұрын
ALL MODELS ?
@kobeissijad
Жыл бұрын
too bad i m just watrching ur video now, ruined my engine for same reason too
@joshpodolsky7740
7 ай бұрын
Just so everyone knows, theres is now another new part number for both gears, now metal.
@benbawden3348
Жыл бұрын
I know we all love a weight saving but I just don't understand why they wouldn't revise a plastic part that's known to fail by replacing it with a metal product, seems strange to me, I'd rather a bike that was a few grams heavier than have grenade anxiety about stuff like this
@sxfwilson6603
2 жыл бұрын
Do they not make metal ones
@dirtbiketv1
2 жыл бұрын
Email me directly - contact info in About tab
@andreasjonsson8075
3 жыл бұрын
How about the 19-21 models? Are theese gears metal know or what?
@dirtbiketv1
3 жыл бұрын
No-- they are still plastic but a updated material and no issues so far-
@andreasjonsson8075
3 жыл бұрын
@@dirtbiketv1 Thank you!
@joshcabral5020
3 жыл бұрын
my 19 has the weaker gear
@jakan756
4 жыл бұрын
How do I get a Dirtbike tv grafix kit to my YZ250 2015.(I want to be the coolest dude on the tracks in SWEDEN😃)
@dirtbiketv1
4 жыл бұрын
Decal works. Or could get you the logo to have made there.
@Prisonmike89
3 жыл бұрын
Does anyone know if the newer bikes come with the updated part?
@dirtbiketv1
3 жыл бұрын
Yes 2020 all have it updated-- it seemed some late 2019s had updates as well.
@danblekeberg2470
3 жыл бұрын
In the video you said years 2016 - 2018. You wrote 2017-2019 ? Which is correct ?
@dirtbiketv1
3 жыл бұрын
Originally we thought it was to 2018 but we have seen some 2019 models with the older gear-
@straighttimestirrups
3 жыл бұрын
Can you clarify if this applies to 2016 models?
@christinedoughertyrealtor9601
2 жыл бұрын
@@straighttimestirrups it does apply to 16s
@billaniii
2 жыл бұрын
So not 2015s?
@motomogul4023
4 жыл бұрын
In the video you said 2016-2018 @ 1:39? Which is it please?
@dirtbiketv1
4 жыл бұрын
2016-19 - it seems most all 2019s. we have heard that some 2019s have the updated gear but the ones we check ed needed the updated gear.
In the vid you say 2016-2018 ... in description you say 2017-2019 ... I have a 19 350 so wondering if my bike has the updated part
@dirtbiketv1
4 жыл бұрын
OK sorry about that-- There is some confusing as it sounds like a few 2019s might have the updated one. The 2019s we checked needed the updated gear.
@rztrzt
4 жыл бұрын
On thumpertalk a guy mentioned his '19 350 EXC-F came with the old part which he replaced with the new part# at 30hrs. To be sure and sleep well I would open it and check! thumpertalk.com/forums/topic/1306112-new-350-exc-f-oil-pump-failure/ OIL PUMP IDLER-GEAR P/N# 79238006100 fits these bikes: HUSQVARNA FC 250 Year: 2020 Year: 2019 Year: 2018 Year: 2017 Year: 2016 HUSQVARNA FC 350 Year: 2020 Year: 2018 Year: 2017 Year: 2016 HUSQVARNA FE 250 Year: 2019 Year: 2018 Year: 2017 HUSQVARNA FE 350 Year: 2019 Year: 2018 Year: 2017 HUSQVARNA FE 350S Year: 2020 HUSQVARNA FX 350 Year: 2020 Year: 2019 Year: 2018 Year: 2017 KTM 250EXCF Year: 2019 Year: 2018 Year: 2017 KTM 250SXF Year: 2020 Year: 2019 Year: 2018 Year: 2017 Year: 2016 KTM 250SXF Factory Edition Year: 2016 Year: 2015 KTM 250XCF Year: 2020 Year: 2019 Year: 2018 Year: 2017 Year: 2016 KTM 350EXCF Year: 2020 Year: 2019 Year: 2018 Year: 2017 KTM 350SXF Year: 2020 Year: 2019 Year: 2018 Year: 2017 Year: 2016 KTM 350XCF Year: 2020 Year: 2019 Year: 2018 Year: 2017 Year: 2016
@briankennedy5403
4 жыл бұрын
@@dirtbiketv1 no worries sir, thanks for the great content
@briankennedy5403
4 жыл бұрын
@@rztrzt thanks for the info mips!!
@moto3moto419
4 жыл бұрын
Lots of secrets when it comes to euros lol. Shockers, but wait how much does it weigh haha. Ooo i have a bike that weighs less its good good it is plastic..😄 Know The Mechanic again and again lots of secrets///failures many people do know of being informed and have witnessed.
@ELCANGRI13204
4 жыл бұрын
Do the 450 and 500 exc have the same problem by any chance with the oil pump gear u just change ?
@dirtbiketv1
4 жыл бұрын
NO-- only the 250/350s
@rztrzt
4 жыл бұрын
No, only 250/350
@ELCANGRI13204
4 жыл бұрын
Dirt Bike TV ok thank you for the reply means a lot
@moto3moto419
4 жыл бұрын
Just all the other problems that come standard 🤑
@MotoRidesVietnam
Жыл бұрын
@@dirtbiketv1 does the 450 exc (mines a 2015 exc-f) still have plastic gears?
@WestHaddnin
2 ай бұрын
Why the hell wouldn’t they make it metal in the first place?!
@robsonenduro3316
4 жыл бұрын
what a stupid design or a programmed failure point...
@davidhill3336
4 жыл бұрын
Has KTM sent out a recall? Do you know what VIN are affected?
@dirtbiketv1
4 жыл бұрын
No.
@0475Mike
4 жыл бұрын
So is Ktm recalling this inferior gear? Or are all of us on our own?
@dirtbiketv1
4 жыл бұрын
It appears your on your own.
@rztrzt
4 жыл бұрын
You're on your own.
@talon0863
4 жыл бұрын
@@rztrzt shh
@Papparratzi
2 жыл бұрын
I replaced both of my oil pumps gears with Hicks Billet gears. Thanks to this video, the process was much easier. From what I understand, KTM racing uses Billet gears and not the plastic ones. That’s all I needed to know before I pulled the nearly $200 trigger.
@stevewhite4078
3 жыл бұрын
Is cam chain slapping noise a symptom of pending failure ? Its 2021 but I just bought an old stock 2019 350 SXF with zero hours from the local dealer here in British Columbia Canada. I did the proper break in heat cycle for 3+ hours and at 3.5 hrs while on the first 60% ride I heard twice a cam chain slap noise, both times at idol and only for 5-10 seconds. Turned around and got back to the truck. Could the failing gear cause low oil pressure which in turn reduces the cam chain tension ? cam chain tensioner as I understand it runs off of the oil pressure.
@stevewhite4078
3 жыл бұрын
PS Loving the channel and the content, half the reason I bought a 350, so many great 350 videos.
@dirtbiketv1
3 жыл бұрын
No your 2019 is fine- a few had that-- but if its that low hours the noise is just a KTM valve train -- they are loud-- All run fine? Email me is best
@Thompsout
3 жыл бұрын
The slapping sound is usually due to the cam chain tensioner. The Dirt Tricks Cam Chain Tensioner will stop the chain slap from happening
@LifeWideOpen780
4 жыл бұрын
Why I buy 30 year old honda lol
@teddyf9438
4 жыл бұрын
Oof
@Gabriel19-87
3 жыл бұрын
Jay The Ktm Sxf 250/350 2020-2022 Have This Problem??
Пікірлер: 202