Thanks for using STA-BIL Fogging Oil! We appreciate it.
@wickedrepairs8527
Жыл бұрын
Absolutely!! It's great stuff, I use it for winterizing motors and for freeing up stuck piston rings too!
@user-tw6wd7sf7h
Жыл бұрын
I just replaced the plugs and oil + filter, I asked my fiancée to shut off the water and jetski after a minute. She remembered to shut of the jetski but left the water in the hose running into the jetski for like 15 minutes before I noticed. Couldnt start it. I assume she got water in motor and exhaust. Oil is now a milky color. I can now start it but only ran what what would leave the exhaust. I believe I need to follow your steps in this video, as well as, change the oil and filter again - right?
@wickedrepairs8527
Жыл бұрын
What a bummer! Yes if the oil is still milky definitely change it, get it as clean as possible. Once as much water is out as possible and it starts up. Run it for a few minutes with no hose, it can run for 3-5 minutes with no water before there is a overheat warning. If a warning starts sounding, just shut it down and let it cool for a while. It is just a warning when the alarm sounds, not an actual overheat. May have to replace the spark plugs again, even if for piece of mind, but wait until it's all squared away.
@franoperkovic1263
Жыл бұрын
Hey its a great video! I have a problem with my yamaha vx deluxe 110 ( 2006 ). Last summer when I was last time driving it and bring it home, I was not able to turn it on so I didn’t rinse it with normal water. It stayed like this the whole winter, and now I called a mechanic to see why I cannot turn it on. It turned out that a starter was broken, and I bought a new one and few days ago this mechanic put it on jet but it didn’t want to turn on again so he took jet ski to his garage to check the problem and today he called me and said that the engine is blocked probably because I didn’t wash it with normal water after the last ride and that is all rusty inside, but he didnt take off motor block, just said to me that the top of the engine is rusty and that I need to buy new clips, rings etc… is it possible for the engine to get blocked because I didn’t wash it with normal water ?? Or this guy want to cheat me or something? I would be very thankful dor the answer as I dont know much about this!
@wickedrepairs8527
Жыл бұрын
Salt water can cause some corrosion internally, but for the top end to be as bad as he says, it would have had to be filled with water. What does it do when you try to start it? Have you tried to unlock the ignition with the code? Even if you did not set the lock code, it can lock from sitting. Is there a fob with the machine? Could be possible that the fob needs a battery or to be reprogrammed. I have seen instances where the motors have locked up do to water intrusion. I have also had motors locked up where I have been very successful with putting some fogging oil in the cylinders and letting it soak and lubricate the rings and become able to turn the machine over. A few motors also that did turn over but had 0 compression and was able to gain it back to 210 psi on every cylinder. Rinsing is important, mostly in salt water, but isn't 100% crucial.
@judgedayan9934
Жыл бұрын
I had water in my jet ski today. I took out the plugs and ran the starter. It expelled a lot of water, but it took only about two minutes (Rotax 717 engine). I then wiped off the plugs and sprayed stater fluid into the air intake. After 5 or six tries, it took gas and completely started up. I let it run a while to burn off all the residual water. The outlet hose inside the hull disconnected and was pumping water into the hull. I and my passenger finally fell into the water when the hull was so flooded it became impossible to balance.
@wickedrepairs8527
Жыл бұрын
I have seen that happen before, what type of hose clamp was on it? I like to use a regular worm style hose clamp when I can on the hoses that have pressure. I hope it runs well the rest of the summer for you!
@cam488
Ай бұрын
my son went out on my 2007 rxp non turbo said it was idling fine through a no wake zone and when he was out at the end of it he went to rip on it he said it just started chugging, he limped it back to the dock and i pulled the plugs and found cylinder 1 and 2 had a little water in them not as much as the one in your video but some. i got the water out and noticed 2 of the 3 plugs cylinder 1 and 2 would not fire so i put 3 new plugs in it and now it is idling fine. i put it back in the water for about 2 minutes and it seems ok but i am worried it could be a bigger issue. I did a compression test and it was even across the 3 cylinders but don't know if i should check something else? also my oil looks good it was just changed before it hit the water.
@wickedrepairs8527
Ай бұрын
Was there any water in the hull as if the hull plugs weren't in, or in all the way it may have been taking on water? Just thinking if there was any water intrusion to the hull, it may have been sucked up from the intake into the motor. If it was capsized, also just be sure it didn't take on water from flipping UT upright again. Also, there's the possibility of a self siphon, did it get towed at all where it may have siphoned water into the exhaust. Besides having a hole in the hull. Those are the most common ways that water could get in. Of course there is if it was on the trailer and having a hose connected without the machine running. But I'm sure that's not the case as it was running fine prior to it having this issue.
@justtisha
Жыл бұрын
What about cracked head/block or head gasket
@wickedrepairs8527
Жыл бұрын
What your question exactly? What's going on? You would have to replace the head if cracked or take it all apart and have it repaired if you can find the right person to do so.
@user-rr5pl4mg3f
11 ай бұрын
Hello, I have the same problem, I have a Yamaha XL 800 2-stroke, it leaks a lot of water, can I use that oil to turn it on or how can I get it to work again? Thanks
@wickedrepairs8527
11 ай бұрын
If there is water in the engine, then definitely try this! I have fixed many motors and gotten them to run after doing this procedure. Sometimes it can take a couple hours depending how bad it is but still better than thousands of dollars and tons of time rebuilding and taken it all apart. Get a can or 2 of fogging oil and a fresh set of spark plugs for when it's all cleaned out.
@user-rr5pl4mg3f
11 ай бұрын
@@wickedrepairs8527 Thank you very much it worked for me, good video. Now I have one last question why is my Jetski only going at 30 mph?
@MD91177
Жыл бұрын
I have a 2 stroke seadoo gtx filled with water exact same thing happening but the water coming out is rusty.. Is it possible water got in my bottom end? Will i have to flip it upside down to drain it all ?
@wickedrepairs8527
Жыл бұрын
Definitely possible that it's in the bottom end. Coming out rusty could be from the steel piston rings. Spray the cylinders real good with fogging oil to help lube it while trying to crank out any water. It will definitely make a mess! Elevate the front of the machine, turning it upside down isn't necessary. Typically once there's enough out that it starts and runs, it will pump the excess out and burn off. The only other way to do it is to remove the head and cylinders to access the lower end and siphon water out.
@MD91177
Жыл бұрын
@wickedrepairs8527 ok I picked up some fogging oil going to spray and pray lol thanks for taking the time to respond, really appreciate it!
@wickedrepairs8527
Жыл бұрын
Absolutely!! Best of luck!! 🤞
@ManuelCuellar-hw9xw
10 ай бұрын
Maybe you can help me with a problem I am having with my jetski It sunk under water we pulled it out it did not want to start once I let it dry, I took spark plugs off there was a little bit of water took battery to get checked its good it cranks it just don't turn on
@wickedrepairs8527
10 ай бұрын
If it cranks over but doesn't start, I would remove the spark plugs and turn it over with them out. See if any water comes out of the cylinder head when you do that. If so, there is definitely some more water in there. If it's only slightly damp and there's not a lot of water coming out, I would definitely replace the spark plugs and try again. It could be that the spark plugs are just fouled or getting wet and not wanting to fire. If there's water in the engine, it will not combust properly in the combustion chamber and allow it to start. Also, check all/any fuses. May have gotten wet and blown a fuse.
@ManuelCuellar-hw9xw
10 ай бұрын
Thanks so much I'm going do all that by any chance is there a number I can call u to or I can send u mine would like to call if I have any more questions thanks
@wickedrepairs8527
10 ай бұрын
@ManuelCuellar-hw9xw you can email me at Cdesousa13@gmail.com
@fedorov5549
Ай бұрын
Put a rag down while blowing compressed air in the holes. Also hold throttle wide open. Takes 5 minutes. Done hundreds.
@wickedrepairs8527
Ай бұрын
Oh yeah! Same here 😆 rags definitely help it but it's fun to see it blow out everywhere 🤣
@rosendocanto9896
15 күн бұрын
What about if doesnt turn on it crancks and sounds like wants to but just doesn’t turn on
@wickedrepairs8527
15 күн бұрын
@rosendocanto9896 the 3 things you need most are spark, fuel, and compression. I would check spark first, if that's good, check to see if you can spray some carburetor cleaner (or starter fluid or fogging oil) into the intake and crank it over. If it doesn't start or try to almost start, then check your engine compression. Engine compression should be 125psi on all 3 cylinders. At least 120, 100 minimum to be able to start.
@rosendocanto9896
14 күн бұрын
@@wickedrepairs8527 i order a engine compresson should be coming tomorrow so ill check engine compression and spark but if the engine compression low what can i do
@rosendocanto9896
14 күн бұрын
@@wickedrepairs8527 i should be getting my air engine compressor and spark plugs tomorrow so ill let you know in 2 days how it goes but if i dont have enough pressure what can i do?
@baileywade443
10 күн бұрын
Just got a jet ski 2019 Yamaha ex deluxe 38 hours, hasn’t been rode in over 2 years, was winterized, I’ve pulled the sparks installed new ones, oil seems to be alittle milky what should be my next step. I’m changing the oil now plus new filter. Should I do this just todo it? To see if there’s anything? The plugs were fogged Oil was low Full tank of bad gas
@baileywade443
9 күн бұрын
On my second oil change it won’t stay running by itself self but everytime I force it seems to wanna run more and more added some sea foam to the fuel also it’s white smoking quite a bit trying to clean up all the old lubrication on it Inside and out.
@wickedrepairs8527
9 күн бұрын
Yes, I would definitely do it, just incase. If the oil is milky, either it has water in it, or it can be from moisture from sitting as well. I would replace the spark plugs as they can foul easily from the fogging oil, provided it was winterized properly. The oil will always read low in them from sitting. Always be aware of that. Yamaha states, that as long as it's on the tip of the lipstick a half inch, it's good!! If the oil level is 3/4 up the hash marks or more when cold, it's technically overfilled! You need to leave plenty of room for expansion.
Пікірлер: 55