I think you should definitely use magnets for the door. A whole bunch of extra-strength niobium magnets alternating with steel plates on both the end of the door and the door jamb. That way when you walk through the door with a screwdriver in one pocket and some screws in the other pocket you can stick to both the door and the jamb and have to pry yourself off both sides. You should probably also keep a pry bar near the door to get it open after it closes. On second thought, a simple mechanical latch might be the better choice.
@dieSpinnt
Жыл бұрын
Hmmm ... looks like there must be a reason why this technique is used f.e. with kitchen cabinets and not a single one magnet closed(endstop holding) door is seen in the wild. This must be an idea of one of those home-automation "enthusiasts" (meaning: wet dream). You know what I mean? Self taught (which is nothing wrong, the contrary is the case) experts where the installation and knowledge grew over time, meaning: No standards, no rules and the total lack of any consistent design. In other words: Total chaos:) It is big fun, while giving a party, the cloud provider decides that he goes out of business ... including the lighting, heaters/air conditioning, entertainment system and so on, hehehe. It is the same reason why people with a brain actually use switches to access lighting (at least have that option and the "old way of doing it" as the priority and as a fallback!!!) and no fancy A.I. or over the air controlled switching (who the actual eff needs light if he isn't PRESENT AT THAT PLACE?! Yeah, there are 100 reasons to have something like that, but all can be done less failure prone or are really dumb ideas in the matter of: Hey! I have a solution. Now we need a matching problem ....). This magnet door endstop idea is something of that kind. Something over-engineered, not well thought through, with the introduction of additional failure points and ... an absolute botch, born out of a feeling. I wish you all a wonderful experience with your old and boring door mechanism! Hehe:)
@yummboy2
2 жыл бұрын
I have to agree with Marius regarding the possibility of using magnets on his sliding door. His solution met the criteria of his priorities beautifully. In my grade book, that's an A++.
@recklessroges
2 жыл бұрын
I second your motion. Magnets would have been the wrong choice.
@jhtnpa
2 жыл бұрын
I understand it would be a lot of work to video and edit all the possible ideas you mentioned but I’d watch every one. Thank you for uploading great content. I always learn something!
@MariusHornberger
2 жыл бұрын
Well, if I do everything mentioned it will be 10 videos or so. Work for the coming months
@Gin-toki
2 жыл бұрын
@@MariusHornberger The videos do not have to be full featured or super in depth, they can also be shorter update videos on the various smaller projects :)
@kyoopihd
2 жыл бұрын
“Nothing beats the space efficiency of pure chaos.” -Matthias Wandel
@wakefieldallan
2 жыл бұрын
Junk drawers for the win!
@chrismoore8231
2 жыл бұрын
I thought the door handle was a great idea. These kind of projects allow creativity and engineering. Great job.
@siriosstar4789
Жыл бұрын
agreed it was brilliant . one of the main reasons for watching videos like this is to see new creative ideas . if everyone did the same thing , it would be boring .
@BikerDaddy402
2 жыл бұрын
As someone who loves restoring "old iron", I'd love to see you work on that little table saw.
@MariusHornberger
2 жыл бұрын
Shit, it's aluminium
@BLenz-114
2 жыл бұрын
Yeah, I'm dying to see that tiny man in action!
@Demothesses
2 жыл бұрын
Having a low work surface like you're proposing for the CNC comes down to how good your back is. When it's low like that you're going to bend over without thinking about it. If your back isn't good that's going to cost you in some pain. If you're back is great, well, no worries (probably). PS. have always loved your videos. Love seeing someone come up with so many of the same ideas and methods as me (see! My crazy isn't unique!). Please never stop.
@2sweetpaul
2 жыл бұрын
Everything you make we will watch and enjoy
@ChuckBronson100
2 жыл бұрын
Hey their Marius, I’m so glad that your going to continue making projects and videos. As far as I’m concerned any video you make is worth watching in my opinion. I like your point of view and the way you approach your projects. Please keep up the great job.
@alexandrenobrega1
2 жыл бұрын
reg. folks saying magnets are better for the door: "talk is cheap, show me the code" ;) great video as always, keep up the good work!
@Digital-Dan
2 жыл бұрын
Your hand-built scissor lift table inspired me, not to attempt to build it, but to buy a 48 inch hydraulic commercial cart. This is a game changer -- useful in so many ways. 60" or more would have been even better, and I'm even considering the 10-20' varieties for rooftop work, either hand-pushed or electric. As I age, my wife's prohibitions against climbing are becoming harder to resist.
@krmusick
2 жыл бұрын
I am really excited to see how you get the tool change to work. Your workarounds always inspire.
@partytempo
2 жыл бұрын
"collects dust instead of creating it" Love it 😄
@_bodgie
2 жыл бұрын
Tool changer will be interesting. You can see the evolution of you skill and capabilities when you compare the drum sander to your later projects. I’m with you, I don’t think magnets would work at all.
@stephenphilp1380
2 жыл бұрын
Glad you chose to value your integrity over sponsorships.
@barnabyjones8333
2 жыл бұрын
Love the shop door handle! Ain't broke, don't fix it. Great design, Works great too. Magnets are too fussy in this case. My vote is for more wood projects, be they tools or furniture, etc. But, I like your variety of topics. Best luck for all the moves, etc.
@Sheycara
2 жыл бұрын
about the magnets, we used the have a harmonica door in our old house that closed with magnets (since it was harmonica it didn't really have the bounce back problem), but every time we had the window open and it was slightly windy, the door would just pop open by itself, and after a few years the magnets also lost their strength and the door would hardly stay closed anymore at all.
@robertomedina1760
2 жыл бұрын
You’re a very skilled carpenter greetings from Mexico, thanks for sharing and sorry my bad English
@jimanddeb
2 жыл бұрын
I'm going to watch all of the videos no matter what you choose to do first so do what you want or need first. Great video
@nicolasmartin9803
2 жыл бұрын
Tool changer looks pretty neat, would love to see that. But in fact most of the projects you publish on here turn out to be source of learning for me.
@120Livi
2 жыл бұрын
Fastest 16 mins of watching nothing much!! Definitely your Grandad's retro table saw refurb for my future project choice
@corymain115
2 жыл бұрын
8:43 DAMN I am looking forward to seeing that!!! Really Cool!
@frankves
2 жыл бұрын
The planer/thicknesser update! I have the same machine without the fancy cutter head. I Actually bought it after seeing your video about it. Still a nice piece of kit.
@aspmos
2 жыл бұрын
I want them all please. Make all those ideas into brilliant videos as usual. Thanks
@sv1833
2 жыл бұрын
Nice to see some new video's again 😉. Danke Marius.
@warrenscorner
2 жыл бұрын
I made my CNC the same height as my table saw but I wish I would have made it higher. I didn’t realize how much I would be bending over to change bits or clamp and unclamp parts. I enjoy all of your projects.
@PhilipStubbs
2 жыл бұрын
Great video. Like the idea of magnets. You should do it, but make it even more complicated than the simple latch. You could have a damper to stop bounce back, and have the magnets on the door side be on a sliding piece connected to the release lever. So the magnets are released by sliding action allowing the door to open. Balance will then be restored with lots of suggestions to keep the simple latch. 🤣
@williamjacobs236
2 жыл бұрын
Any and All of them from you Marius . Another great video.
@josephlee7325
2 жыл бұрын
I agree with you about the door thing your latch system is the best way to do it
@gabrielgomescunha
2 жыл бұрын
My rule is that I don't argue if I have doubts about what I'm saying and over the years and the more I learn more doubts I have. Another thing I've learnt from History books is that you don't argue with a German if you don't have a thousand ways to prove he's wrong.
@simonbergman5970
2 жыл бұрын
I think the algorithm will love restauration of the old drill press :P
@marcrouillard881
2 жыл бұрын
+1 for shopvac cyclone upgrade!
@wernerviehhauser94
2 жыл бұрын
Hettich has some neat auto-closing components for drawers, they could also word on that door.
@a0flj0
2 жыл бұрын
You _could_ use magnets, spread across the entire height of the door, together with a mechanism that should slide one side up or down, when opening, to break the magnetic coupling - that would also quiet the ones complaining about overengineering. For me, the most interesting projects will definitely be the furniture projects. You could, in fact, use some over-engineering for the tool changer, to not take up space on the CNC's working area permanently. I'm thinking a mechanism driven by a separate controller which brings a disc holding multiple tools into the table area, then slides it out, and where one particular tool slot can be dialed from the controller.
@iTzNabGamingPvP
2 жыл бұрын
Der Effekt am Anfang ist ja geil. Hab ich noch nie so gesehen... :D
@alberttibbets6567
2 жыл бұрын
More on the Magnets Controversy. Much as I enjoyed the development of the mechanical door latch, I felt it set a dangerous example of self-motivation in pursuit of personal satisfaction. Yes, very clever, and Yes, I shared the good feeling of the sound of the latch closing. But, I think the will of the people is clear: Buy the Magnets! regards, O. Tibb, CEO, Acme Magnet Corp ps: I find your videos so entertaining and inspiring. Thankyou
@hippie-io7225
2 жыл бұрын
Great update! Please do the automatic tool changer; I think there are a bunch of us with these types of CNC routers that would like to use them more effectively.
@MariusHornberger
2 жыл бұрын
I spent the last week working on the design, it's definitely coming soon
@johnniewalker39
2 жыл бұрын
Before getting lost in the negative comments, please look again at how many people click like. We generally don't write comments, but we love your content.
@momsonthenet394
2 жыл бұрын
No matter what projects you upload, however infrequently, I'll be watching!
@davem4256
2 жыл бұрын
I enjoyed the door handle video a lot, showing your design process and problem solving skills are very helpful. You are a maker, showing us how you make things is why I'm a subscriber. Keep up the great content.
@d.i.d
2 жыл бұрын
Tool changer will be great for me ;) Now I have 2.2kw spindle on HNC and there is a lot of power to work...
@MariusHornberger
2 жыл бұрын
I think this tool changer won't work for the 2,2kw spindle. Or you need a different tool changer unit
@d.i.d
2 жыл бұрын
@@MariusHornberger ill do HNC changer 😛
@jirihala8684
2 жыл бұрын
Is there any link for that exact tool changer ? :) curious
@MRrwmac
2 жыл бұрын
Marius, I’m shedding tears for your old first tool build dismantling! Oh well. I think you should build what you need most for the move. About the CNC, if it’s too low you know your going to stack stuff on it as a shelf. When you get around building a base for it, Perhaps build it as high as it will fit under but with all the future improvements you want to make. Hope the move goes well for you, your family and your sisters new place.
@jrumbel
2 жыл бұрын
very keen on your shop vac video ideas....just emptied my shop vac today....some inspiration wouldn't be a bad thing :D. Agree about the magnets being a less than perfect solution for the door. Good luck with all the moving.
@graemebrumfitt6668
2 жыл бұрын
Restoring the old stuff please Marius! TFS, GB :)
@lelandclayton5462
2 жыл бұрын
I have a solution for the pocket door and magnets. A recessed universal 12 volt mag lock. 12 volts power supply, request to exit button inside the shop and a PIR on the entry side to the shop. It's way overkill for that application but it's a solution none the less to it. I honestly prefer the handle you made for the pocket door.
@fotopfanatic
2 жыл бұрын
Occasionally, there are moments where I want to start my own KZitem channel, but as a person who thinks in the same mindset as yourself, I realize many of the comments on channels I subscribe to are clearly from 'armchair analysts' who haven't thought through their comment before posting it. Your assessment of the magnets for the door is spot on. There are multiple reasons why you don't see magnets as a solution - some of which you have outlined here. Another reason why they aren't used is because magnets are brittle. Closing a door with any significant force will shatter them. Even if you leave clearance for them not to touch when the door is closed, you still have to think about humidity which will cause the door jamb to move throughout the seasons, and this will change your magnet clearances. KZitem comments can be a gold mine of information, but they can also be a garbage bin of 'advice'. At the end of the day, you'll never be able to satisfy everyone, and ultimately, the shop is yours and not theirs.
@MariusHornberger
2 жыл бұрын
If you want to start a channel, do it. As long as you enjoy what you're doing others will enjoy too. Only thing to keep in mind as you already mentioned: You will never ever satisfy everybody.
@alexiselsass1143
2 жыл бұрын
The restoration of old machines + the CNC Tool changer really tickle my interest !
@steveoddlers9696
2 жыл бұрын
I would definitely watch all the video ideas you mentioned, especially one about the drill press. For whatever reason I just like drill presses, don't judge me.
@rolandkeys8297
2 жыл бұрын
You are right about the magnets for the door. Glass shower doors use a strip magnet to hold them closed and keep them water tight, you have to close the door and hold it to stop the bounce back. They also are mounted on plastic tubes to allow for any slight misalignment and that is on a glass edge that is perfectly strait. sometimes we make stuff for the pleasure of making it not for its practicality or to please the comments
@sarahtompkins24
2 жыл бұрын
Always enjoy your furniture or cabinetry projects listening to your thought process is very enjoyable for me keep up the good work and I’m looking forward to your next video
@glenellynrunner
2 жыл бұрын
The tool changer sounds interesting and ridiculously difficult. viel Glück
@2Skinny
2 жыл бұрын
Anyone who calls you out for "over engineering" obviously hasn't watched your channel long. Keep up the good work.
@EigenkonstruktDe
2 жыл бұрын
Viele Grüße aus der DIY-Staubsauger-Ecke 😅 Gutes gelingen und starke Nerven.... Viele Grüße Andreas
@mprobison
2 жыл бұрын
Hey man, I'm not really a great fan; but I do recall watching the initial videos on your drum sander. Then and now I probably don't know my own leg from a drumstick; but I wanted to tell you that I loved your honest breakdown of your past work. You framed it wonderfully, and your mindset was really positive in the editing. Good work, and I'd love to see more. "The only person we should feel superior to, is past selves."
@gregwmanning
2 жыл бұрын
I like your door lock way better than magnets
@ernsteliden6719
2 жыл бұрын
I personally love that latching door lock. And if you made a video showing you mount 4 magnets what do you think you would have gotten in the comments then?.. You're absolutely amazing, and keep up your great work👍👍👍👍
@gregaltenhofel7326
Жыл бұрын
I like the door handle as it is.
@jefferyhunter1665
2 жыл бұрын
I really appreciate your projects that you share. I'm in the process of starting a wood shop, equipment is ordered. I really admire your ingenious and creative ideas. Thank you.
@thibaultjehl2856
2 жыл бұрын
I would feel emotional unbuilding one of my home made machines. I'm sure you have a mixture of nostalgia and proudness of your younger self when you look at this clever machine, even with some little rooky mistakes. Great video as always. Cheers from France.
@ale6242
2 жыл бұрын
As someone who has actually used magnets to keep a door closed. you absolutely need both a lot of them, and you need the alignment to be correct as you say! Mine is just to latch a door once its close to closed. if i shut the door with force it still bounces back as you showed!
@glenturner4985
2 жыл бұрын
Id like to see you restore your grandfather's tools , a tribute to him !
@alans1816
2 жыл бұрын
It's good to see you back, and easy to imagine why you might not have time to make videos so often. What I want to see is the next thing you find compelling to do. It was instructive, but not surprising, to see how far you have come in the ability to design quality machines: your earliest ones worked, but your current efforts are much better. Keep your CNC well above flood level.
@lynntraylor1646
2 жыл бұрын
Like watching your videos. Always informative.
@kylechrystal4532
2 жыл бұрын
Although you criticize your homemade machine - it served an excellent purpose - it taught you so much! Yes, in retrospect your build may have shortcomings, but to get to the point where you could recognize those things and know how to improve them you had to first understand simply building a machine - which is a big task on its own. And instead of holding on to this now unused machine for nostalgia - the value it had as a record of your work and previous thinking is actually not lost when you disassembled it because you have nicely documented the machine with this video. I think this is the best possible result. Well done!
@MariusHornberger
2 жыл бұрын
It was interesting to see how I did things back then. And I also achieved the goal of using as many different screw types as possible ;)
@supadeluxe
2 жыл бұрын
Looking forward to the CNC tool changer! I also agree with your magnet theory.
@hdwoodshop
2 жыл бұрын
I think the only way to make the magnets work is to add an energy absorbing mechanism. Like a wheel what turns the momentum off the door closing to a contract plate with magnets… not as elegant as your latch. Ignore the haters. I’d love to see you build another dust separator integrated into the vacuum.
@brucemillar3015
2 жыл бұрын
I like your door latch. Very cool...
@JustinAlexanderBell
2 жыл бұрын
New machine, always excited about linear rails.
@unionse7en
2 жыл бұрын
UCCNC is a nice, high value with many inputs/outputs, easy to customize, great support & forum also it can talk serial so basically unlimited expandability.
@wardprocter2371
2 жыл бұрын
My vote for the future project would be the upgraded dust collection system. Thanks for all the work you put into making these videos - they are entertaining and informative. I love seeing your thought processes and problem solving, all delivered with a dose of self deprecating humour. Your channel ranks as one of the best on KZitem!
@darinmbicknell
2 жыл бұрын
He is BACK! Electromagnet? That would work.
@peggyt1243
2 жыл бұрын
Intelligent, creative and resourceful. What an awesome combination. I truly enjoy your videos.
@Basti5792
2 жыл бұрын
Watching a youtube video in a youtube video. We're reaching new levels here :D
@JockeSelin
2 жыл бұрын
So interesting to see. Evolution of skills and ideas is a very important aspect of knowledge. It’s easy to look at something and say; “Well that’s a stupid idea”, but often there are several valid factors behind it that are the reason why things are the way they are. Learning from these reason is much more valuable than just looking at something and saying it’s rubbish. Thanks for the video, Marius! 😎👍🏻
@guillermocarrillo3959
2 жыл бұрын
Wow, glad to see you’re back. Missed your videos, I enjoy them so much. Hope to see you more often.😊
@andersax1
2 жыл бұрын
Looking forward to your project with the linear rails.
@MariusHornberger
2 жыл бұрын
Me too. The design is almost finished
@julianlech8505
2 жыл бұрын
I would vote for furniture projects but restoring old machinery is also interesting.
@mickgentry8128
2 жыл бұрын
Your videos are always entertaining and inspirational so whatever project you decide to do works for me. thank you Marius. Cheers
@julianreverse
2 жыл бұрын
Make sure to install a cleaner for the tool changer, blowing out any dust before inserting the next tool.
@JThyroid
2 жыл бұрын
My dad made some nice shaker style white oak cabinets in the 90's, and he used neodymium magnets on the tops and bottoms of the doors to keep the doors closed. The magnets came unglued from their holes mostly in the frame and not the doors. I'm guessing wood expansion and shrinkage broke the glue bond. The magnets that came loose from the doors probably got shaken loose from the doors coming to a sudden stop (and wood movement) even though they've never really been slammed shut. Magnets are great, but mechanical latches can be so much better in certain situations.
@siriosstar4789
Жыл бұрын
That Ulmia saw is super cool . I imagine it will last a very long time . i had an old industrial 1/2 inch drill form the fifties that i inherited . it ran at 450 rpm's , one speed . the torque was so insane that if the bit got stuck you had to immediately let go and step back until it stop .i tried to hold on one time and it threw me to the floor .
@christianp3388
2 жыл бұрын
I'd like to see furniture builds. Never gets old.
@chrisnorton2837
2 жыл бұрын
Would be most interested in the new furniture you will be building, but I also like old tool restorations. I'm sure I will enjoy whatever you decide to film. ☺
@jessjulian9458
2 жыл бұрын
Tool changer, can't wait.
@leonardocecchin6488
2 жыл бұрын
Suggestion on CNC table height: from my experience I think it is better to have it at a comfortable height (maybe a bit lower than a workbench, but not much), I find myself often having to look closely to the workpiece, or looking at it from the side for aligning stuff, or simply to have a sneak peek under the dust shoe... Good luck with the toolchanger, very curious about that! ;)
@bodoque_csm
2 жыл бұрын
I would like to see how you tackle the challenge of the Router tool changer
@matthewboyd443
2 жыл бұрын
Dont worry about what everyone think or says, You do You and I will continue to watch. Cant wait for more vids, keep it up
@aragorndedolor4171
2 жыл бұрын
My advice for your cnc hight, I noticed you have your jointer/planer on comfortably working hight. You probably don’t use that daily hrs on end so why don’t you have that machine standing on the floor? Treat yourself and your cnc machine with the same respect as your jointer. My cnc has a frame/table hight of 810 mm. I am 1.85 m tall. I raised my table to 950 mm. My experience is it’s comfortable working hight to secure material, tool change and do visual checkups. Unfortunately we all get older, unless you want to rearrange your shop in future again you will be pleased to get that machine on a height to work comfortably on while you can, in planning the setup. You will spare your back and incase your eyesight deteriorate it’s much easier to do visual checkups ore any work on the router without your reading glasses, they are on and off, become a lose fit, falling of your nose... My personal experience as I am over 60... That automatic tool changer could be a very interesting future project.
@recklessroges
2 жыл бұрын
Love the playful editing in this video. (Made me smile.) The audacity of "people from the Internet" telling you to, "just use magnets". You are correct about the magnets. They are probably thinking of electromagnet doors, (which obviously isn't the right engineering choice in this case.) Your design is elegant and perfect.
@andypire6278
2 жыл бұрын
-KZitemr “Woby Design” has his cnc under a work bench. It seems to work well for him. -Magnetic door catches are a nightmare, for all the reasons you mentioned. Electoral-magnetic catches are nice but aren’t cheap and smaller ones need a soft close.
@perlytkemeyer7693
2 жыл бұрын
A comment on placement of your cnc. To optimize use of floorspace in my shop, I build a cabinet to store small sheets of wood and offcuts, it has the size of a euro pallet 80*120cm and about 100 cm in height. My cnc then is placed on top of this. The end of my cnc is overhanging on one side of the cabinet and thereby allowing for cutting tennons vertically as well as horizontally.
@Locane256
2 жыл бұрын
Definitely the automatic tool changer. Not that I'm *ever* going to do something like it myself, but I love living vicariously through you and seeing things that work wonders come together 🙂 Also about that - I don't know what you have in mind for being able to sense the tool or not, but speaking from experience working on (software) projects with similar constraints - "no visibility" problems are REALLY shitty to work around. I want to encourage you to simply upgrade the device to have more input / outputs (is that an option?) rather than try to work within a problem space of not knowing some critical information. It's almost always a bigger headache than it's worth.
@bickybickford
2 жыл бұрын
I like the door latch that you made. But if you were to use magnets, I think the best bet would be to mount the magnets at or around the top of the door at the header in a line or linear. Line the small magnets from side to side to slow the door as you slam it shut. Kind of what they do with bullet trains or roller coaster braking but with rare earth magnets not electro-magnets.
@sailingstoph9765
2 жыл бұрын
I have seen some refrigerators, and many freezers, that have a flexible magnetic strip within the door gasket. That might have worked? Providing some shock absorption for the door closing, and a seal against noise?
@HuntersOA
2 жыл бұрын
A tip for the tool changer if that is still in the scope. What we do at work in these cases, is we have a hall effect sensor or some other proximity sensor connected to a stand where all the tools are. If an improper tool is missing we disturb the signal - in your case maybe cut the power or something. But than again, you must solve how to detect what tool is missing... Tough. Maybe just buy a new controller board? Alternatively you can always add a PLC / raspberry PI to interface with a tool holder and the CNC and not allow the CNC to move if the improper tool is picked up or not picked up... It should be possible to add an intermediate interface to your CNC albeit it might require a lot of coding.
@MariusHornberger
2 жыл бұрын
I bought a proximity sensor for that purpose a month ago. And I think I have a neat way of implementing it into the existing controller
@HuntersOA
2 жыл бұрын
@@MariusHornberger lovely stuff! Good luck with the implementation, and I am looking forward to a vid about it :)
@edmuff82
2 жыл бұрын
I think the bigger the Cnc the better it is to lower the table. I have a 4x8ft machine. And loading big 18mm ply sheets on it is a struggle even though it’s only like 55cm of the ground. Though when I’m doing smaller work I miss not having the bed higher up. psyched to see the ATC project!
@legochamp1
2 жыл бұрын
the toolchanger by far!
@NielsNL68
2 жыл бұрын
i look forward to the toolchange project ;) that is something i would love to make for my new 1419 CNC table. But more then with your cnc the space to add it on my cnc is very small.
@moium
2 жыл бұрын
I'm anxiously waiting on the dust collector rebuild
@MariusHornberger
2 жыл бұрын
You mean the big dust collector (no rebuild planned) or the shop vac?
@JohnZanussi
2 жыл бұрын
Definitely interested in all your upcoming projects (as always) but more so for the updated dust collection as I’m looking to do something similar soon.
Пікірлер: 343