Excellent video and helpful. Watched it on my iPhone and first thing I thought I saw was a guillotine. Yikes.
@mudweimer768
3 жыл бұрын
Thanks
@labtrainer09
3 жыл бұрын
Excellent work. I especially liked the vertical bracing for the glue-up and the advice on applying two different thicknesses of resin to the joint. Do you by any chance build plywood boats for a living? If so, how would a prospective customer get in touch with you? By the way, your inboard-mudboat video brought back WONDERFUL memories of my first day of fishing the marshes in one. What GREAT boats these are.
@mudweimer768
3 жыл бұрын
Carpenter by trade build boats as a hobby also taught boat building classes for a few years I started scarfing plywood for a local lumber yard when the longer lengths became unavailable. I do repair boats and occasionally build one through my Business last one I built was for the free state of Jones move
@mudweimer768
3 жыл бұрын
Movie
@sandyvosburg5237
4 жыл бұрын
Best video i've seen on scarfing ! How far back did you set your straight edge from the end of the plywood for your jig to run along? I've been thinking about a West system jig but wasn't sure if it was good quality. By the way, where are you from, Louisiana?
@mudweimer768
4 жыл бұрын
Pretty sure it’s 3 5/8 didn’t get a chance to measure it .the jig is made for a regular 7 1/4 saw but I’ve always had it on a 10” saw with no problems and one of the most important things is the table you lay the sheets on needs to be flat! South East Louisiana
@sandyvosburg5237
4 жыл бұрын
Awesome, I'm from Lakeland La. (False River area, Pointe Coupee Parish). Is that the West Systems Scarffing Jig? and how does it work on 1/4" plywood. Been thinking about getting one to make a Pirogue
@mudweimer768
4 жыл бұрын
Yes west systems works great on 1/4 and 3/8 need to do a little extra planning on 1/2 3/4 and 1”. Lafourche Parish
@701SUMO
4 жыл бұрын
What's the TPI of the circular saw blade, did you cut an 8:1 scarf ratio, and what was the blade angle used to achieve the correct 8:1 bevel?
@mudweimer768
4 жыл бұрын
It’s a west system scarf jig mounted on a 10”saw that is set to 7.5 degrees. Between the angle of the jig and the 7.5 angle on the saw it cuts an 8:1 bevel. Not sure how many teeth it’s at the shop and I’m not but it’s the blade that came with the saw and it’s cut tons of scarfs without ever being sharpened!
@multihullminion9201
4 жыл бұрын
Any content from scarfing 3 mm plywood? I had the best luck using an inclined router jig a stout router and a 1-1/4" mortising bit to do so
@jimmyghersi
2 жыл бұрын
Scarf plywood
@sandyvosburg5237
2 жыл бұрын
Do you let the thin coat of epoxy dry before applying the thickened coat of epoxy?
@mudweimer768
2 жыл бұрын
No wet it out with thin epoxy then apply thickened epoxy ! The thin one allows it to soak in to the wood for a better bond and thickened one helps fill all the voids
@sandyvosburg5237
2 жыл бұрын
@@mudweimer768 is there a way to contact you by email or messenger? id like to see if i could hire you to scarf and epoxy a couple sheets of 1/4" Aquatek
@mudweimer768
2 жыл бұрын
I live in south east Louisiana if you’re close by that’s fine? Other wise shipping would be crazy
@sandyvosburg5237
2 жыл бұрын
@@mudweimer768 I'm about an hour and a half from Houma / Thibodeaux area. I live by False River (Pointe Coupee Parish)
@Ultramesh
4 жыл бұрын
Are you using Fast or Slow Epoxy there? And what is the thick epoxy thickened with? To what consistency?
@mudweimer768
4 жыл бұрын
I use the extra slow during the hot summer months and the fast when it’s the cooler months the filler is 406 colloidal silica thickened so that it’s still slightly runny
@mudweimer768
5 жыл бұрын
Ask questions please I’ll help you you in any way I can!
@firerescue3214
4 жыл бұрын
Do you have measurements or plans for your jig?
@mudweimer768
4 жыл бұрын
The clamp is just basically a straight edge the piece bolted to the saw came from west system epoxy it a scarf jig they sell for a 7 1/4 saw
Пікірлер: 26