Bro I don't know shit. This only video I've found. Totally going for it
@jeremccurdy
11 жыл бұрын
@johnny yates. Once you set the spring and bolt back into the cylinder wall, the spring automatically sets the tension on the chain. No need to set or adjust it.
@barryc.768
8 жыл бұрын
great vid...very detailed and explained nicely...very helpful, Thanks
@jeremccurdy
11 жыл бұрын
Compression cycle can be found a couple of ways. You can take the spark plug out and put a piece of napkin or tissue over the spark plug hole. As you turn the crankshaft into the compression cycle, air will be forced out of the now open spark plug hole and blow or move the tissue. Then you just watch your timing mark until the T lines up. Or, another way is alittle bit easier. Just go ahead and take the head off. Then line the timing mark up on the crankshaft. . . .
@jeremccurdy
11 жыл бұрын
As for the RTV. Some people use it, some don't. I didn't use it on mine and it sealed up and worked perfectly. That's just my ecperience though. Good luck.
@parkersplanet
8 жыл бұрын
Thank you for sharing this, I have a head gasket to replace on a CN250 that is very similar and this is helpful.
@jeremccurdy
11 жыл бұрын
Then, you can set the camshaft on the head to the point where both valves are closed and the alignment marks on the camshaft sprocket are lined up properly. Then when you reassemble, its just a small turn of the camshaft to make the timing marks line up.
@HiDeguild
Жыл бұрын
My guy, I know this video is ten years old but I'm still gonna ask: why does the head gasket not have all the water cooling ports cut out?
@jeremccurdy
11 жыл бұрын
That depends on what problem you're having. If you have coolant in your oil or notice that your coolant level is dropping without a leak, then you probably have a leaking head gasket like this video. The other possibility is a leaking water pump oil seal that I show in another video. As far as the exhaust noise is concerned; I don't have the experience or the knowledge to give you any advice on that. Sorry.
@BradSophia-n5v
Ай бұрын
So how much time would this take ,seems pretty straight forward
@BradSophia-n5v
Ай бұрын
@jeremccurdy I'm confused what did you mean by moving the chain before removing the head can't I just maintain the tension on it while pulling the head off
@J.Jevnager
5 жыл бұрын
great video, thanks!
@RogerThatPetSitter
11 жыл бұрын
are you supposed to use the rtv gasket sealer stuff on the head gasket??
@mangmans
11 жыл бұрын
Ok im lost, I thought the head gasket was just a thin "Washer" like that is just above your exhaust pipe. For the sound so its not so loud, I have a 2007 sunl scooter, I was told by a fellow rider that I should replace that. was I told correctly?
@bigzen69
3 жыл бұрын
I took The timing chain Tension screw out not knowing what it was But I put it right back in and tightened Could I have messed up something because now I have Antifreeze in my oil Thank you
@jeremccurdy
3 жыл бұрын
As long as you didn't run the engine or turn the motor while the tension screw was out, it should be fine. If you did run the tension screw removed, the timing chain can jump a tooth on either of the sprockets it is wrapped around. That will mess up the engine timing and make it run poorly or not at all. It won't cause the coolant in the oil problem. My advice is replace the water pump seal first. It's an easier and cheaper process. Then if you still see coolant in the oil, change the head gasket. Good luck.
@bigzen69
3 жыл бұрын
@@jeremccurdy Personal thank you so much for your Speedy reply No I did not run The Honda 150 Elite Deluxe but there is one thing there was antifreeze coming out of the air filter And I believe it was coming through the carburetor This Bike set for 28 years before I started it Clean the whole coolant lines out I believe the thermostat Did not open I cleaned it out I will test the thermostat today before I put it back in It was leaking at the thermostat also not the O-ring cuz I could not get that out the first time Finally got it I will start with The water Pump seal like you suggested thank you so much Dennis
@Quattro4k82
3 жыл бұрын
Life saver
@uhmazingpreston
8 жыл бұрын
When I tried to set the timing, I couldn't find the "T" you're talking about but I found a mark that looks like it was done with a sharpie so I assumed that was the mark. I then set the chain on the cam shaft exactly like you did and after reassembling some of the parts, I tried to start the engine and it didn't start. I took it off and the camshaft was upside down from where I set it when I put the sharpie mark back in place. This happened 2 other times and I'm not sure why. Any help?
@jeremccurdy
8 жыл бұрын
The only thing I can think of is that the cam sprocket is slipping on the can shaft. Beyond that, I'm afraid I can't be of much help.
@Islandcitymedia
6 жыл бұрын
I see you didn't change the lower gasket how long did that last? I got 78 miles before it blew again
@50ccminimoto
11 жыл бұрын
hi mate good vidio so how do you set the timing chain tensioner were you put the bolt in with the spring thanks
@babygirliciousness
7 жыл бұрын
Great video☺!!
@uziXwraith
5 жыл бұрын
show the top end valve lash setting?
@spivzespivatron659
6 жыл бұрын
I found out that my problem wasnt the gasket it was the rings had gone .but itd tightened up the head bolts ?do u think it will be ok to put my new rings on and reuse/set the head gasket ?or do i have to buy another one even tho the one on now has never been used ?im not sure if it will work now as obviously the squish may have gone on the first install?
@repnatl
5 ай бұрын
😂 ummmmm head gaskets can't be reused even if it's been torqued down only once.
@Jail-Left-Wing-Traitors
10 жыл бұрын
very cool vid, very helpfull thanks ;)
@JoseRivera-ix8dj
9 жыл бұрын
Innovación
@uziXwraith
5 жыл бұрын
this is the clone of the #hondach250 engine. thank you.
@RogerThatPetSitter
11 жыл бұрын
how do you know your on the compression cycle??
@repnatl
5 ай бұрын
Any Google search could have answered that. Stick a piece of wire or extension into the spark plug hole. Then turn the engine with a socket until the wire or extension can't go up any further and its just starting to lower again. That's TDC.
@lenny0347
4 жыл бұрын
chain tensioner destroyed my motor, horrible tensioner
Пікірлер: 33