You can download the notes (PDF) for this video using the following link: bit.ly/46vh8UI For more videos on Sequential Circuits, check this playlist: bit.ly/43SvUmj
@ioannaathineos5269
8 ай бұрын
Best teacher on earth!!This guy is a genius !!!
@newbie8051
11 ай бұрын
Tried implementing the same in verilog.... woah, loved it
@singhkaptan00
8 ай бұрын
Thanks for explaining these concepts in great detail. Question :- Is the sequence generator made with the FSM different from the one with the shift registor?
@ALLABOUTELECTRONICS
8 ай бұрын
Yes both are different one.
@M-13myroslava
8 ай бұрын
The best teacher in the world
@poojashah6183
Жыл бұрын
Best explanation 👌🏻👌🏻👍🏻👏🏻
@joele29
7 ай бұрын
Fratello io ti amo, grazie per il video e se passerò l'esame sarà anche merito tuo❤
@hadijaffri9856
8 ай бұрын
You are an absolute legend. Also I want to ask,what would we do if we were to use a JK flip flop for the implementation. How do we figure out how many flip flops to use?
@who.abhinav
2 ай бұрын
what is name of your simulation software? also great explanation
@ALLABOUTELECTRONICS
2 ай бұрын
Its deeds circuit simulator.
@studymail4800
Жыл бұрын
hello sire, how to know what to put in the preset and clear of the flip flops in the simulator?
@ALLABOUTELECTRONICS
Жыл бұрын
Generally, the preset and clear inputs of the flip-flop are active low. Meaning that when 0 is applied as an input then it will get activated. So, when we want to clear the flip-flops then we should make clear input 0. And we want to make them inactive, we should apply 1. This is valid, considering the inputs are active low. If they are active high, then you need to do other way around. I hope, it will clear your doubt.
@studymail4800
Жыл бұрын
@@ALLABOUTELECTRONICS thank u very much, indeed cleared my doubt 🙌
@studymail4800
6 ай бұрын
Indeed, thank u very much@@ALLABOUTELECTRONICS
@MANIKSINGHprasad
Жыл бұрын
Great Video Actually !!!!!!!!!!!!!!
@saibatapasen433
Жыл бұрын
Sir, which software are you using for simulation?
@ALLABOUTELECTRONICS
Жыл бұрын
Deeds circuit simulator.
@bhavanimurugesan9026
10 ай бұрын
@@ALLABOUTELECTRONICS Is it open source software
@markuz5535
9 ай бұрын
hi, I tried following all the steps for another string but If I try to simulate the circuit It never gives output 1...any chances I can contact you somewhere to share my work?
@ALLABOUTELECTRONICS
9 ай бұрын
Perhaps, you might have made some error during the design steps. You may contact me via mail.
@Kat-zx2je
11 ай бұрын
thank you so much!!! 🙏
@mathswithpana
24 күн бұрын
good day sir. which software are you using for the simulation?
@ALLABOUTELECTRONICS
23 күн бұрын
Deeds circuit simulator
@ΝικΝοκ
10 ай бұрын
Very good
@TusharDabhade-ei9sp
5 ай бұрын
Kal kiska paper hai DLD ka?
@govardhan8962
Жыл бұрын
Actually I have one question related to fsm can u give the solution for the question
@SLUGTHUG
Жыл бұрын
The solution is the Y output.
@rahulc0dy
8 ай бұрын
Which simulator is this?
@ALLABOUTELECTRONICS
8 ай бұрын
Deeds circuit simulator
@SLUGTHUG
Жыл бұрын
Great tutorship 🙏
@ravichaudhari5949
Жыл бұрын
What is application used for simulation?
@ALLABOUTELECTRONICS
Жыл бұрын
Deeds circuit simulator
@rahulmp4459
10 ай бұрын
How did you determine the Q1+ and Q0+ ???????
@ALLABOUTELECTRONICS
10 ай бұрын
It is written from the state table. For example, when x=0 and present state is 00 then next state is also 00. ( see the left table). According to that, in the second table ( right one), the Q1+ and Q0+ is 00. Similarly when x=1, then next state is 01. So in the second table in the fifth row Q1+ and Q0+ are 0 and 1 respectively. I hope, it will clear your doubt.
@JyotiJadhav-k7c
7 ай бұрын
Which s/w you design and simulator
@ALLABOUTELECTRONICS
7 ай бұрын
Deeds circuit simulator
@박소은-b9k
3 ай бұрын
If the number to detect is not 1001, but 0101, can I set A, B, C, D to -, 1, 10, 100 like the video?
@박소은-b9k
3 ай бұрын
Or should I set B, C, and D to 0, 01, 010?
@ALLABOUTELECTRONICS
3 ай бұрын
@@박소은-b9k Yes, you should set the states like this only. (B = 0, C = 01 and D = 010)
@박소은-b9k
3 ай бұрын
@@ALLABOUTELECTRONICS Then, how should I set it up when I make one circuit that outputs 1 when 0101 or 1001 is an input?
@ALLABOUTELECTRONICS
3 ай бұрын
which sequence you want to detect? 0101 or 1001.
@박소은-b9k
3 ай бұрын
@@ALLABOUTELECTRONICS I'll write the question I'm trying to solve. "The circuit examines groups of four consecutive inputs and produces an output Z=1 if the input sequence 0101 or 1001 occurs. The circuit resets after four inputs. Find the Mealy state graph."
Пікірлер: 50