Available on Amazon 20503 Kit: a.co/d/cYSWJRq 10105 Puller: a.co/d/9DD3IYz 10202 Installer : a.co/d/45eo1YA 70300 Pliers: a.co/d/0Zx7TOP
@billrau2398
2 жыл бұрын
Outstanding !👍🏽 video I never knew this tool existed till now I just ordered one can’t wait to start using it 👌🏽
@louislowe-o5b
4 ай бұрын
I just bought one it works great I’ll never use the old socket and hammer method again 👍
@phendrix9476
4 жыл бұрын
Bought the 10105 a while back. Used it today to press out my ‘01 Dodge 2500 front axle u-joints. This thing made it extremely easy! Used a 1/2’ Cordless impact. Just used my balljoint press to reinstall. Well worth the money imho.
@2vcrew782
2 жыл бұрын
Snap On BJP1 BJ press ?
@zappatx
2 жыл бұрын
This would be great for on the road rescue operations. My only issue was the drummer for the background music. So all in all good review.
@AK99581
Жыл бұрын
Yeah that background music is pretty goofy lmao..."dun dun dun dun!!"
@toddbernal4143
6 жыл бұрын
On sale on amazon only 99 bucks for the removal tool! A must for any flat rate mechanic.
@Mr1968gtx
11 жыл бұрын
At 3:29 all I was doing was pushing the bearing caps in tight enough so they wouldn't fall out while I got the C-frame in to place. The cross of the u-joint slid in freely. I have however done what you suggested years ago on my Jeep... I had to change the joints out 3 weeks later!
@dc5723
3 жыл бұрын
I wished my Toyota u joints bearing caps came out this easy. Not only I used the Tiger Tool to push out the caps, I had to pound them out with a brass punch and 2 lb sledge hammer.
@khimsophacarfixing
2 жыл бұрын
These two tools are easy to remove and install!
@smotleyjr79
10 жыл бұрын
only issue with this is the damn PRICE! If they sold them for $50 then more people would use it and buy it....
@oby-1607
4 жыл бұрын
I picked up a set at a yard sale for $5. Works awesome, the woman who sold it didn't know what it was.
@markkulyas2418
4 жыл бұрын
If it was $50.00 it would be a piece of junk that would bend or break.
@eprn1n2
3 жыл бұрын
If they gave it away demand would go through the roof!
@tnsd5801
3 жыл бұрын
Was your car cheap? If you can't afford to maintain your vehicle. Might I suggest public transportation or a bicycle or old fashioned walking. Proper tools that are of sufficient quality to repair vehicles without breaking are as you put it "is the damn PRICE!". You must think the people who work on cars should do it for free. I mean it's so easy a quadriplegic mud puddle can do it. You have no skills because you have no idea that tools of any craft cost money. You are the burger flipper demanding $15/hr and being replaced by a self order kiosk.
@Anubis78250
12 жыл бұрын
Now lets see you do that on real world u-joints ... you know the ones that have been installed for 20 years. Those came out way to easy, and it didn't look like it was because of the tool. Seriously though, why not just use a ball-joint puller.
@jimsperlakis5634
2 жыл бұрын
Yeah, and how about ruining the Aluminum style yoke while he's at it with the single end tool !!!
@derekhellam9861
7 жыл бұрын
I have the puller except fit heavy truck drivelines love it
@blass5506
4 жыл бұрын
I use a c clamp an a socket easy removal and installation I’m not a mechanic but handy
@TheSauce05
12 жыл бұрын
Just did the u-joints on my 2000 F-150 and there's NO WAY this tool would have worked to remove the old ones. Since I didn't have a vice it took me and a friend to hold down the driveshaft and use the ball-joint/u-joint press to press the joints out and the new ones in.
@wormius428
5 жыл бұрын
My 95 f250 has an internal c clip for the front passenger joint so this tool will save me hours of work since you cant fit a press there. Very excited to get this
@SnakeRiverFishing
10 жыл бұрын
Nice, gotta stick to my hammer and drift method over here though $$$
@1AAuto
12 жыл бұрын
Great U-Joint video.
@howardgriffith71
3 жыл бұрын
I need mine done you made that s*** look easy
@lauratwo16
12 жыл бұрын
4 tons / 2 = 2 tons on the Tiger Tool.....My Tiger Tool has handled that kind of force no problem. JP-USA
@spawnsrevenge
11 жыл бұрын
@ 3;29 it is possible that he didn't make sure the u-joint was inserted far enough into the cap and a needle bearing may have fallen out of place. That will not allow the cap to go into it's proper position and could destroy the u-joint if not done properly. May be why it appeared to be hung up.
@TigerTool
13 жыл бұрын
@TsmnnDvl5 Hi TsmnndvI5, We have manufactured these tools for over 20 years and have yet to here of a case where this has happened. Generally speaking the yoke ears are stronger than the cast portion of the glove that pulls against the yoke.
@Doomzdayxx
10 жыл бұрын
This would totally be worth it if it cost like 20 bucks
@johnnysix7162
9 жыл бұрын
No kidding... they want hundreds for an overglorified C-Clamp.. you can buy a damn press cheaper!!
@regorekrub
11 жыл бұрын
What happened to the one that didn't want to go down..?
@sd90mac61
4 жыл бұрын
He had to remove it and reline the bearings, that does happen sometimes.
@abel442
11 жыл бұрын
A BALL JOINT REMOVAL TOOL WORKS ON REMOVAL AND INSTALLATION I OWN ONE ,IF YOU DONT OWN ONE AUTOZONE RENTALS ARE FREE JUST LEAVE A DEPOSIT, BTW CLEAN AND LUBRICATE ALL MATING SURFACES TO MAKE THE JOB EASIER.
@28704joe
4 жыл бұрын
Bearing cup mating surfaces go together dry, not lubricated.
@leehotspur9679
3 жыл бұрын
@@28704joe No, Anti seize or rescue steel used sparingly stop corrosion and dry face shearing
@28704joe
3 жыл бұрын
@@leehotspur9679 Howard, look this issue up on the Spicer website. Cheers. "Caution - Spicer DOES NOT recommend wiping the outside of bearing cup assemblies or yoke cross holes with grease, oil or silicone-based sprays. This could result in bearing cup assembly rotation in yokes. "
@Nico-iv1cq
3 жыл бұрын
Good tool.🙂
@robbieharris9339
3 жыл бұрын
I have NEVER had a u-joint come out that easy OR go in that easy also. They have always been rusted in.
@jeepsblackpowderandlights4305
4 жыл бұрын
Cool video but expensive.. Id rather take a 5 lbs sledge and smack the ears with the shafts on a angle and in two or three good whacks the cap will pop off.
@sarmientosarmiento2338
4 жыл бұрын
Amigo te hablan de aquí de Colombia Qué precio tiene esa herramienta para cambiar crucetas Gracias amigo
@GorillaFPV4life
6 жыл бұрын
Those tools would have been really nice to have... a hammer and sockets worked really well though lol. He didn't even finish lol
@kentellis9071
7 жыл бұрын
Handle it! 👍
@cbettridge
12 жыл бұрын
I noticed you aren't using an impact gun on that.....can it handle an impact gun. It would make that job really go fast, making more money! This tool could pay for it self in no time.....speaking of that, how much does it retail for? Thanks
@piglett2195
13 жыл бұрын
looks good , probably better than my BFH & big block of wood that i use : )
@lauratwo16
12 жыл бұрын
Just keep in mind your BJP method required approx. TWICE the force a Tiger Tool needs. In other words the Tiger Tool would do that U-joint with HALF the effort you used. JP-USA
@benbai66
11 жыл бұрын
i could have one knocked thru with my hammer and socket before you could get that thing on good lol
@lowrider3030
11 жыл бұрын
Think logic ......How often will ya really use it?....I'll stick to a deep socket and the mallet.......Old skool and effective.....A girly girl could do it with a $300.00 tool.
@ivezb
7 жыл бұрын
Tool porn music😂😂😂
@TigerTool
12 жыл бұрын
The 10105 & 10202 are engineered for use with a 1/2 impact gun. If you do a quick search in Google for "Tiger Tool 10105" you should come across a few prices or if you wish to purchase the item locally we have a dealer locator on our website.
@brutalblues
7 жыл бұрын
Anybody got one I can borrow?
@HowToolVideos
11 жыл бұрын
I found the 10105 puller online for $164 and the 10202 bearing cup installer for $163 so I am not sure where you are getting your prices but you might want to try somewhere else.
@evo2037
5 жыл бұрын
what the tittle of music?
@ScASpiKyBaLL
12 жыл бұрын
HAX!!!!!!
@rmartinjr83
6 жыл бұрын
A hammer takes less time
@ricgomez1
7 жыл бұрын
That music is annoying, damn... its not type of music for working on cars with.
@teflondonhks50caliberbarre72
9 жыл бұрын
$300 are you fucking kidding me sockets & Hammer that's the best...
@Satchmoeddie
8 жыл бұрын
That was my reaction. F__K THAT! It should be hydraulic for that kinda coin.
@brutalblues
7 жыл бұрын
The music...
@donnaedminster1463
8 жыл бұрын
I installed the u-joint with this tool and I used my solid gold 3/4 ratchet
@Nostradamus_Order33
5 жыл бұрын
Donna Edminster 😂🤣
@johnb1121
3 жыл бұрын
😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂
@Macsmoney
2 жыл бұрын
You clearly were trying too hard!! He only used a silver 3/8 ratchet. By the way…….he did it in 6 minutes, how long did your big hammer take? Time is money in a shop, and having done hundreds of u-joints I would buy this tool again if mine broke
@WeTrudgeOn
9 жыл бұрын
Don't worry, harbor freight will no doubt have a clone pretty soon for 40 bux for the pair, those could be produced somewhere in Asia for five bux each.
@hddm3
9 жыл бұрын
wish they would hurry up
@hddm3
9 жыл бұрын
hddm3 don't know why these places want to price there selves out of the market. pro or not, that's just to much money
@Satchmoeddie
8 жыл бұрын
Especially with that cast crystallized recycled monkey metal they use. I thought, "WOW< these Harbor Freight deep clamps are awesome for $12. They are okay to repair a guitar, but anything where you need some force the frame breaks apart rather violently.
@lauratwo16
12 жыл бұрын
By design, force is applied ONLY to ONE cup, NOT TWO as with a typical ball joint press (c-frame). Tiger uses approx.HALF the force a BJP would take to do the same U joint. For those seized-up stinkers it appliest approx.TWICE as much force as the BJP at a given scrw pressure. If it looked too easy it's because it was TWICE as easy using TIGER TOOL. I took time to say this because they are GREAT to deal with... I got AWESOME customer sevice recently thamks to KEVIN. I don't forget that. JP-USA
@tonyshook2624
7 жыл бұрын
I BET HOME BOY HAS BEARINGS LAYING DOWN INSIDE THE CUPS . THOSE CUPS WEREN'T INSTALLED ALL THE WAY. OTC BALL JOINT PRESS 120 BUCKS WITH AIR TOOLS PREFERABLY.
@billjabsjabbing9120
6 жыл бұрын
so C clamp and a big socket would be about the same thing?
@delta614
5 жыл бұрын
basically
@all4runner316
4 жыл бұрын
I just tried c-clamp, it couldnt handle the job. Ball joint tool works well.
@alexhaywood9706
8 жыл бұрын
If the driveshaft is bigger than that tool it won't work, a ball joint tool is just as good and does another job too. Replace ball joints as well. Great marketing
@louisernesto5886
3 жыл бұрын
You all prolly dont care at all but does any of you know a way to log back into an Instagram account..? I was stupid forgot the password. I would love any assistance you can give me
@jamietitus6220
3 жыл бұрын
@Louis Ernesto Instablaster ;)
@louisernesto5886
3 жыл бұрын
@Jamie Titus Thanks so much for your reply. I found the site on google and I'm trying it out atm. Looks like it's gonna take a while so I will get back to you later when my account password hopefully is recovered.
@louisernesto5886
3 жыл бұрын
@Jamie Titus it did the trick and I finally got access to my account again. Im so happy! Thank you so much you really help me out!
@jamietitus6220
3 жыл бұрын
@Louis Ernesto happy to help xD
@robertcowan8211
6 жыл бұрын
LUBE THREADS ON PULLER, REMOVE GREASE ZERK FIRST
@Nostradamus_Order33
5 жыл бұрын
Why not use a two jaw gear puller?
@dfjohnson76
8 жыл бұрын
this thing is $385.00! I don't know who buys this thing. if you have a shop and are trying to run a business you can't spend $400 for this thing. the savings in time vs. doing it the old way will not off set the cost. profit margins are too tight for extravagances like this. BUT I WOULD LOVE TO HAVE ONE!
@JacobWilliams83
12 жыл бұрын
Those could not have been the factory joints. My 10y/o factory joints w/90,000 miles on them took an 18" breaker bar just to move 'em...
@michaelwilliams2275
2 жыл бұрын
Dam right I got biceps for days but U joints Kicked some ass today Had to lube twice to get out
@youandiryan
5 жыл бұрын
I have one of these. If the u-joints are very rusted you will have to use a combination of hammer and socket technique, and this tool. This tool does not push universal joints out well when they are very rusted.
@terrellscaife2411
3 жыл бұрын
It sounds like you’re not using the tool properly because I went and got an old rusty driveshaft from the junkyard and I was able to press the caps out
@colinkennedy908
5 ай бұрын
Just did mine rusty crap on 88 cherokee. Pb blaster and ratchet. Not too shabby at all.
@youandiryan
5 ай бұрын
@@colinkennedy908 yeah I could have been doing something incorrectly haha honestly I don't remember now that was like 5 years ago. Those new joints that I have installed on the day that I left my original comment 5 years ago are still good to this very day!!
@sschapasc
11 жыл бұрын
Needle bearing jump out on ya? Cool tool, but I'll stick with my 20 ton press.
@AZDESERT2024
5 жыл бұрын
$100 for a C clamp . Available at Home Depot for $10
@SidewaysGts
11 жыл бұрын
Seems like a great tool for a shop where you miiiiight encounter that 1 in however many cars where a hammer/socket wont work.. buuut for the rest of us? Ill stick to a hammer/socket. Awesome idea though, just with the price was a bit easier on the wallet.
@ohell226
3 жыл бұрын
I like tools. 9 years later KZitem pops up in feed. Not enough rust on that to be impressive. Plus cost for DIY. Already own two sockets and BFH.
@terrellscaife2411
3 жыл бұрын
Amazon and eBay how the knockoffs for $50 or less
@Ace135Trill
11 жыл бұрын
bro for that amount of money you can pay a shop to do the whole job
@triiko
10 жыл бұрын
Would be great if you did a lot of u-joints or if money is no object.
@tevsil1
8 жыл бұрын
you realize the "installer" c clamp does the exact same thing with a little more positioning right?
@ykmalachi
2 жыл бұрын
But what about using a hammer and socket like a caveman for 30 minutes?
@AZDESERT2024
5 жыл бұрын
The caps in the shaft ears, aren't even flush.
@tomjoad1363
6 жыл бұрын
When you use the C-clamp to put the little retainer back in place, how does only one side is pushed inside, and not both since both jaws of the clamp are sitting on the U-joint outsides?
@smileyrod11
8 жыл бұрын
i use a hammer a vise them out
@MrRahimhosein
6 жыл бұрын
pedro rodriguez english please
@TheBracket1
4 ай бұрын
You'd think they would design a better driveshaft that doesn't have the internal groove that gets smashed and the retainer doesn't fit after you have to put 9 million lbs of pressure to get out
@travisaudioelectronics12vo90
Жыл бұрын
I purchased th 10105 and it does not work on Chevrolet 1500 alumium shaft , it slips off.
@anthonypeterson5618
8 жыл бұрын
Nice but putting that cup on should b one side at a time or risk hitting the pin bearings in cup then.....u kno what happen then.
@michaelwilliams2275
2 жыл бұрын
It’s one of those too easy videos No oil used No lube Just did u joints on an old car Wouldn’t move This works easy on clean u joints that have been done before
@Roadking556
3 жыл бұрын
Ok just had one pretty much explode on me. . I'm sure this tool wouldn't have worked on that one
@harleytholomewsullivanquin6300
Жыл бұрын
Doesn't it bothers you that's called puller but it's actually pushing?!!
@brianxr4160
8 жыл бұрын
It's $176 on Amazon on 12/13/2015. I'm going to trade the 6 year old whiny one sitting across the table from me for one of these tools.
@ricgomez1
7 жыл бұрын
BrianXR Every one has a whiny kid, there isn't a big demand for one of those.
@brucearner
2 жыл бұрын
What if you have joints with clips on out side ?? Nothing in video on that !!
I saw that to. Was wondering if it was done on purpose or if he made a mistake?
@dericross341
Жыл бұрын
Like to see that done with a 1480...it can't. Waste of time and money.
@pengchengwang5606
9 жыл бұрын
puller is good. Installer canbe replaced by shop vise.
@terrinewman7390
6 жыл бұрын
the installer is just a modified c-clamp
@eastcoastjay1983
6 жыл бұрын
I like how he stops installing the second cup because he probably jammed the bearings lol. you can see the cup sticking out when installing the yoke. too expensive! ball joint press and a hammer is the way to go
@iwillnotcomply7145
2 жыл бұрын
U-joints in Minnesota do not just come apart lake that. LOL
@BillyDocWalker
5 жыл бұрын
Auto Zone will lend you these tools
@KillaKliff101
3 жыл бұрын
Could be seconds if you had an impact.
@Ham68229
13 жыл бұрын
What are the chances/odds of this tool bending the "eyes" where the caps go while pressing in or out? A very interesting tool kit.
@billw4646
2 жыл бұрын
This type tool eliminates the risk of spreading the ears on a yoke because instead of pushing them apart like we used to pounding them out with a BFH or using a ball joint press you instead are only pushing on the sides of the opposing yoke's ears (or the u-joint trunnion after you have one side out) where there is no risk of spreading them and pulling on just one ear while pushing the trunnion. There is no risk of spreading the ears on the yoke when there are no forces applied in opposite directions to both ears like the old-school methods would often do, especially if one cup was seized up like when a seal got stuck or someone forgot to remove a clip or someone used an impact on a press and hit it with too many uggaduggas. This type tool is an improvement over the factory recommended press adapters that push on the trunnion as it works on the same principle in that it only is applying force to one ear instead of both but this type adapter fits a wider range sizes of u joints. FWIW now that I suppose the patent ran out or whatnot there are other companies now making their own versions of this tool, like OTC and Lisle. FWIW the Lisle has held up pretty darn well in our shop for being half the price of the original Tiger.
@TheBracket1
4 ай бұрын
Mine broke the first time i used it
@yassermahrous2371
2 жыл бұрын
هل من الممكن اعرف سعرها واين نباع
@supermoistdeluxe
2 жыл бұрын
You don't need a c clamp to press them back in. Take a second to clean the cap hole out and debur the edge. They slide back in
@Rick-bt6je
8 ай бұрын
Thanks for the great video tutorial, very much appreciated
@Steve0885
2 жыл бұрын
Nice but I'll keep my bfh 😄
@PeaceBong
5 жыл бұрын
I like it but I find the use of 2 separate tools to be excessive. Both removal and replacement can be achieved by using a balljoint press which is similar to the install tool shown. Great demonstration though.
@speelksurche
7 жыл бұрын
very good
@No-vm7go
6 жыл бұрын
Great looking tool, but I just used one of those big u-joint presses and broke a cap. I went back to using a socket and hammer.
@doghouse96zj92
5 жыл бұрын
i made the same tool along time ago out of a pitman are puller and a large c clamp and a socket. a bit over kill on the price
@AWD_T
10 жыл бұрын
Very nice. Beats a hammer and a socket. How much for the puller?
@thomaspeters9174
3 жыл бұрын
Where can i get one....🍻🍻🍻
@jakepryor
10 жыл бұрын
Nice, minus the price. Absolutely ridiculous, around $200 to $300 for just a single tool. I'll stick to hammer and cheap socket. Can also go get this made if you know any metal fabricators, or get a steel beating rod made for like next to nothing.
@HexaFox
10 жыл бұрын
You can get one on Ebay now for about $160.00. Still ridiculous for me. I will probably use it once in my entire life.
@ding0925
10 жыл бұрын
A ball joint press works better and is much faster...get one and harbor freight or just borrow one from autozone ..
@Satchmoeddie
8 жыл бұрын
A gigantic vise, a big socket, and an even bigger socket.
@Satchmoeddie
8 жыл бұрын
Why not make one that used a small bottle jack ram and hydraulically presses the part out???? I just used a big__s hydraulic puller set made by Backhawk back in the 1950s. Amazing stuff them old Blackhawk tools. Blackhawk even made a conduit bender that would bend 1/2 rigid"- 2" thinwall, and 2" rigid conduits and it was the size of a small suitcase, but it did weigh about 90 pounds. Their U Joint Pitman arm puller set had a portapower type hydraulic pump, and the same type clamp & ram assembly.
@dalestewart7733
7 жыл бұрын
I've bent yokes pressing them out with a chinese 10 ton hydraulic press. I think a hammering action is better than brute force pressing. I might try an attachment for my long stroke air hammer.
@astrogypsy
5 жыл бұрын
Sweet, but it's the bench vice and sockets for me.
@Nordic_Mechanic
12 жыл бұрын
*ducks out of the way of any possibly thrown computer monitors*
@TheRealCharlieSuper
3 жыл бұрын
Cool, I'll just stick with my ball joint tool kit...
Пікірлер: 194