Tech tip for those o ring cap plugs. Take a hammer and a brass punch and smack the plug. It’ll help prevent stripping out the hex plug. Thanks.
@stevepickett4258
Жыл бұрын
Thank you so much for making this video. You are doing a great job. I’m doing this to mine RTZ-S
@LawnZip
Жыл бұрын
Thank you for the comment! I'm trying to put out good content. I'm also learning myself! It's nice to know the video helps someone!
@ragazzoitaliano1982
7 ай бұрын
How did it go on your RZT-S? I just bought 1 myself used (little over 200 hours) and am wondering if you should service the transmission
@silverdragontaylir8252
4 ай бұрын
Study gearbox diagram(know where to drill and tap), prevent damage
@dRmM4tw
4 ай бұрын
Just bought a used john deer z445, I am trying to find the diagram for the tranny Tuff Torq TZT 7-D, but I cant find the diagram... I would like to study and drill/tap but where can I find the diagrams?
@wilE6764
Жыл бұрын
Good video dude..i have an older zforce..had the caps on the transmissions that were like 4 inches long..kinda like a rubber hose sticking up with a plastic thread that got brittle from heat they both broke off..do you know if i can get new caps?..and where do they sell that fluid?
@LawnZip
Жыл бұрын
Best bet is ebay. Gonin Google and type your full model number from the mower tag and then find the parts diagram and go by part number.
@LawnZip
Жыл бұрын
Jack's small engines or parts tree usually has parts diagrams for everything.
@wilE6764
Жыл бұрын
@@LawnZip ok thanks
@LawnZip
Жыл бұрын
@@wilE6764 no problem! You may have to use the model number from the hydro itself tok hard saying.. Usually it will show it all on Jack's or parts tree. Hope that helps!
@mikeking6748
Жыл бұрын
My rzt50 uses 20w50 motor oil in the transmissions, 1.75qts
@froggerman44
6 ай бұрын
Have u ever thought of drilling and tap the bottom of the case? For draining?
@froggerman44
6 ай бұрын
Also how often?
@LawnZip
6 ай бұрын
@@froggerman44 I plan to do mine every 100hrs. I'm too scared to drill them lol
@crisprtalk6963
3 ай бұрын
So is that where the fluid should be, right at the top of the fill hole?
@LawnZip
3 ай бұрын
Close yes. It will run out of the overfill if it's over full.
@ttor50
11 ай бұрын
how often should the fluid be changed?
@LawnZip
11 ай бұрын
I'm not sure since they are "unserviceable" but I'd say about 100 to 150 hrs.
@LawnZip
11 ай бұрын
The first change should be the most important. Getting all the gunk and shavings out out from the break in period has to be good for it.
@joefro9473
Жыл бұрын
WELL, THAT REALLY SUCKS!!!!
@LawnZip
Жыл бұрын
What part lol?
@rubbensmagloire9717
Жыл бұрын
When the lawn mower over heats did you end up fixing that problem?
@LawnZip
Жыл бұрын
@@rubbensmagloire9717 as in the engine? My engine dosent overheat but if yours does I'd suggest you take the shroud off and clean around the engine.
@rubbensmagloire9717
Жыл бұрын
@@LawnZip not the engine the hydro transmission. I thought I saw you comment on another persons video that if it’s humid out after a while you loose power accelerating
@LawnZip
Жыл бұрын
@@rubbensmagloire9717 nope the guy I was talking to may of said that. Mine works fine it was just due for a change.
Пікірлер: 26