as someone who has only recently gotten into car audio, your videos have been extremely helpful and its a sin you arent more popular. Props!
@DIYAudioGuy
4 жыл бұрын
I appreciate that. KZitem is a slow grind my channel will be big one day, it just takes time.
@showty4lo
3 жыл бұрын
On my life, all the way from Chicago boss man lol. You need your own company or podcast that goes national, because I was screwed over on my sounds, but I cleaned up nicely after watching your videos. Mad respect ✊🏾
@arthurhughlett2292
13 күн бұрын
@@DIYAudioGuy Is it possible to accomplish this through a factory head unit without db slope?
@DIYAudioGuy
12 күн бұрын
@@arthurhughlett2292 If the amp has a crossover then you can use the crossover on the amp.
@VoltzIsSalty
3 жыл бұрын
Out of all the youtubers doing audio equipment, your videos have definitely been the most helpful. Especially in showing that you don't need a fancy $300 SMD DD-1 to properly set the gain or other parameters.
@DIYAudioGuy
3 жыл бұрын
Those are great tools and I would love to have one. But you can't really justify spending that much unless you are doing it for a living.
@angelvip2474
3 жыл бұрын
I totally agree. Do you need one for personal use? No. I do it for a living and it comes in super handy. You don't need a mobile detailing trailer to wash your personal car but if you do it for a living, a bucket, rags and dish soap won't cut it😉
@angelvip2474
3 жыл бұрын
You are definatley one of my favorite audio KZitemrs. Great info. Great contribution not only to the diy guys but the industry as a whole. Keep up the great work bro
@DIYAudioGuy
3 жыл бұрын
I'm just a normal guy with a camera and some power tools! If I can do this stuff anybody can.
@jasonmcedward2595
Жыл бұрын
@@DIYAudioGuy do I put one lead on positive and one on negative speaker terminal?
@JeremySchoeder
3 жыл бұрын
Pro tip, double tap the recent app button to toggle your last used app... Great crossover info! Thank you.
@DIYAudioGuy
3 жыл бұрын
Cool, thanks!
@anhnn2479
Жыл бұрын
Old but gold, today I just finish tweaked x-over regarding to your guidance. 12db/oct by amp & 6db/oct (Butterworth) by HU at same spot 100Hz. No need to switch polarity in sub cause 180degree phase (3rd order). My system now mixed micracle. Thank you!
@DIYAudioGuy
Жыл бұрын
Nice work!
@mikez4719
2 жыл бұрын
Im so glad i found this video again. Recently got a new set up and its in need of some tuning. Thanks for your help!
@DIYAudioGuy
2 жыл бұрын
Glad to help.
@johnnyohh-yt6284
Жыл бұрын
one of the best, if not the best, crossover setting videos out there. thank you! if you felt like it & had the interest, .... you can record voltages over a frequency band/range and adjust the crossover to max/min and test the amplifiers crossover slope. then you can graph results and see if the crossover slope is as claimed! :)
@lightingbunker4326
3 жыл бұрын
All your videos are great and this one in particular has been extremely helpful as I’ve struggled to setup the crossovers on my four channel amp. Spent 30 mins this morning setting the gain and crossovers and my car sounds fantastic. Thank you, sir. Subscribed :)
@DIYAudioGuy
3 жыл бұрын
Awesome! I'm glad I was able to help.
@patrickseitz2473
3 жыл бұрын
this is way better than what the amplifier manuals tell you to do
@DIYAudioGuy
3 жыл бұрын
Interesting, I have never read the manual. At least not the part on setting the crossover.
@patrickseitz2473
3 жыл бұрын
@@DIYAudioGuy the manual on my JBL subwoofer amp says something like "turn the frequency down until you can't hear any mids and highs." really appreciate the video!
@giltyal5912
Жыл бұрын
Your videos are Awesome! Thank you for simplified but correct ways to get where we're going!!
@DIYAudioGuy
Жыл бұрын
Thanks!
@doughoshauer2232
Жыл бұрын
I've always dependes on the 2 object on the side of my head. Called ears if it don't sound nice and clear something's amiss. Kind of like timing my trucks engine you can hear a miss . Nothing fancy just ears. Great video I also keep my volt meter in my pocket it's am everyday everything tool.
@mightymight365
2 жыл бұрын
Wanting to get a voltage reading of your crossover for the technicality is cool (awesome job on showing us!), but is it really necessary? I find that crossovers have to change according to what you're listening to. At my home entertainment system, when I'm watching a movie, I set my crossover on my subwoofer to about 80 htz so that the dialogue doesn't come through. When I'm listening to music, I set it to about 120-180 htz (depending on the type of music) so that I can hear the upper-ish mid frequencies of the bass guitar and not just the kick and floor tom. It's set all by ear. No multi-meter required. Don't beat yourself up guys if you can't get this math right. Lower your crossover to cut off the frequencies you do not wish to hear through your sub (that's what it's designed to do). If it sounds muddy, cut some more out. If you want more beef/punch, raise it up some. Again, don't worry about the numbers. Hear it.
@DIYAudioGuy
2 жыл бұрын
I don't disagree. The ear is the best test instrument.
@christopherconkright1317
Жыл бұрын
How do you choose what test tone for what you want
@gkk2001
3 жыл бұрын
My amp manual tells me to do this by ear using a 75% volume set point which for me is impossible and entirely guess work. I look forward to use your multimeter method. Thank you very much.
@DIYAudioGuy
3 жыл бұрын
You can spend a little bit more and get an oscilloscope and be even more accurate. kzitem.info/news/bejne/0HiEq4iocnN5qnY
@jdipo16
4 жыл бұрын
This is the correct way to do it proved with the DSP. Great Vid!
@DIYAudioGuy
4 жыл бұрын
Either that or my DSP does it wrong. 😆😆😆
@chadcurrent1645
Жыл бұрын
I like the video and details but I must have missed the one that explains how you choose which frequency you are targeting? For instance how do you know how high of hz to set your subwoofers frequency? 80, 100, 120. What frequency range your mids can play, and what frequency is the lowest frequency your tweeters can handle ?
@DIYAudioGuy
Жыл бұрын
I did not cover that in this video. I don't think I have a video that talks about that specifically.
@dieselsmiths
5 ай бұрын
Seems informative, but I must have missed how to calculate the voltage factor, or is that standard related to the slope. I like knowing where and why…I’m not the “because that’s what they said” guy. Great videos by the way.
@DIYAudioGuy
5 ай бұрын
I used the formula for DBv kzitem.info/news/bejne/laF63omZgHWWa4Isi=3XMWroosrXic56Iz
@xavibrown7615
2 жыл бұрын
Maybe i missed something but if your unfiltered voltage is 50v and you are driving a 1ohm load. At 80hz 24db/oct slope your target voltage is 25volts. You have to apply the 0.251 to the wattage ( @1ohm load. 50v x 50v = 2500watts ; 2500 x 0.251 = 625watts ; square root of 625w = 25v. Take it or leave it guys . Not trying to argue with anyone. DIY guy you are still awesome.
@DIYAudioGuy
2 жыл бұрын
Crossovers are not based on watts, they are based on DB. You have to convert from DB to volts to find the crossover point.
@JoshM7
3 жыл бұрын
Well this is a nice video on crossovers that I’ll definitely be using in the future. Normally I don’t need exact crossover settings, but this’ll come in handy for my highpass that needs to be set at 17 or 18Hz 2nd order. And I’ll want that to be almost perfectly set because I’d rather not bottom out my lil Ultimax under 18Hz. Wish I had DSP in the car because in the house my Inuke DSP makes it so simple just type in the number and select the slope and done. (Though it doesn’t let you DSP below 20Hz sadly)
@DIYAudioGuy
3 жыл бұрын
What size Ultimax?
@JoshM7
3 жыл бұрын
@@DIYAudioGuy It's the 10" that I've mentioned in another comment on another video of yours. (The one I've planned with 3 10 inch passive radiators)
@hypershine6080
4 жыл бұрын
Gentleman you have a new subscriber
@DIYAudioGuy
4 жыл бұрын
Welcome to the adventure!
@lexluther919
Жыл бұрын
thanks bro....save me confusion. i didnt know the knob of the screw to set the htz mids to highs even tho knob set on the number dont mean its the number...wow....amps are sometimes hard to figure out at times
@chrisadame7641
3 ай бұрын
I have a skar RP 1200.1D. The specs says it’s a 24 dB/OCT. It also had a subsonic filter that goes from off to 50hz. The LPF goes from 50 hz to 220. I have the LPF at its highest like you said l. Whenever i multiply the unfiltered voltage by .251, the number i get is too low. No matter how low I go on the LPF, I can’t get the multimeter to that number i calculated. Could that be a result of a cheap multimeter? Or what could it be?
@TheFlyingHernie
Жыл бұрын
I like the way you explain everything. I don't have a DSP, so I was looking at using the crossover on my amp. How do we find A:the db/octave slope that our amp uses? And B: the "unfiltered voltage"? Should we just leave the crossover off, and see what voltage we get out of the speaker terminals, and use that?
@TheFlyingHernie
Жыл бұрын
I have the SKAR audio RP-150.4AB for my mids and highs and And Hifonics Zeus ZRX2400.1D for my sub. Bought my sub and amp years and years ago, and am now trying to do a proper setup in my car.
@DIYAudioGuy
Жыл бұрын
Unfiltered voltage is just that, it's the voltage without any filters on. It does not really matter what the starting voltage is. I recommend turning the head unit up until you get 10 volts just to make the math easier. Your owner's manual should tell you what your crossover slopes are and the type of crossover.
@speedpros
3 жыл бұрын
Your 1st dude I seen set x-over settings with a multimeter, very informative. Can the same process be done on a external 4way x-over made by zapco or prv or whoever
@DIYAudioGuy
3 жыл бұрын
Yes!
@ravensix4290
Жыл бұрын
Do you use the same test tone as you used for gain setting? Like if you used a -5db 1000hz for gain setting a 4 channel, do you use a -5 db tone at specific hz to set crossover?
@DIYAudioGuy
Жыл бұрын
If you are setting the crossover at 80 hz use an 80hz tone, if you are setting the crossover at 1500 hz use a 1500 hz tone. The volume of the test tone does not matter. I tinker with the volume on the head unit so that I start with 10 volts, that way the math is super easy.
@kevinc6073
3 жыл бұрын
I have a NVX JAD1200 and its a 24octave amp. I put my volume at 28 and played a 75hz tone. I put the crossover the highest it could go and I got a reading of 31.5v. I multiplied the unfiltered voltage to 0.251 and it's 8.85. I lowered the level on the crossover and did not lower more than 20v. So I lowered the volume and Got it to 8.0v (by luck) I Tried getting to 8.8v but the next notch jumps to 9.5.
@DIYAudioGuy
3 жыл бұрын
That's a solid amp, I have the 4-channel version. I wish they still sold the JAD line, I am not fond of the newer VAD line. I am sure they are good amps, I just don't like the look. I have been doing a lot of research on crossovers and have had some good feedback from viewers, here is what I have learned: There are different crossover types (bessel, buttworth, linkwitz-riley), they are all implemented differently, and not every company implements them as intended. I think for that amp your best bet is to set the crossover using .708 (the -3 db down point). Most importantly, set it so that it sounds the best. The technical stuff is fun, but the music is what matters. I hope to get some updated crossover videos out when it warms up!
@kevinc6073
3 жыл бұрын
@@DIYAudioGuy I love this amp, it fits under my passenger seat and it swallows lots of juice and the power sounds clean. I'm also using their 2ohm VCW 12" Sub in a vented enclosure at 32hz.. That's interesting I did not know that there's different crossover types. I'm also using the Audio Control LC2i LoC and it sends about 9v pre amp out put. Can that affect the reading on the multi meter? .. At the end I put the crossover on the amp one notch over because it sounded better.
@DIYAudioGuy
3 жыл бұрын
@@kevinc6073 The voltage from the LC2i will not impact the crossover setting, but it will impact the gain, with that much input voltage you can keep the gain low. You will have less noise in the system.
@kevinc6073
3 жыл бұрын
@@DIYAudioGuy I used your other video to help guide me to set my gain. I had a feeling it would impact my gain setting because my subwoofer is pretty loud and it is a 1/4" Turn before the half gain mark on the amp. I might even have to turn it down one more notch. Wanted to give the woofer exactly 1000rms
@3RDERA
5 жыл бұрын
Nice dog 🐕 Had a question I wanted to ask you, What’s your take on this?, why wouldn’t every amplifier that comes with a crossover adjustment, not give you the option to have it adjustable down to 0. For example, the infrasonic filter on most bass amplifiers in today’s market are adjustable from say 20-50hz or 15hz-35hz. This doesn’t allow someone the opportunity to not use the filter, because even at its lowest point, it is still cutting the voltage. What I hear from most people is that you shouldn’t notice that much of a decrease in loudness in those range of frequencies from having it at 15hz as compared to an amp that doesn’t have one, but I beg to differ. Some of these amps nowadays have 24 dB slope on the Filter, and that really does affect a 20hz tone even having the filter it at its lowest point of 15hz. Sorry for the long winded comment and question. Keep up the great content!
@DIYAudioGuy
5 жыл бұрын
Now that you mention it, that seems kind of odd. when I get to my computer I will try to type up a thoughtful response for you.
@DIYAudioGuy
5 жыл бұрын
OK, here is what I think! Let's say you set the subsonic filter to 20 HZ, and it is a 6DB per octave linkwitz riley, it will be down 3DB at 20 HZ. Then down 6DB at 15 HZ and down 12DB at 7.5 HZ. Down 3DB at 20HZ is not much at all, but it is kind of a moot point since most subs are going to roll off before they get down to 25 HZ. Setting the subsonic to 15 HZ is practically the same as setting at at zero. But this is just my best educated guess.
@3RDERA
5 жыл бұрын
@@DIYAudioGuy i appreciate the response. In my experience, 99% of amps that have the subsonic filter on the amp, is either 12db per octave or 24. i think rockford had one amp that had 18db per octave but was a one off idea. 6 db down at 20 hz is definetly noticable to me, especially when listening to full orchestra performances i have on cd's or watching movies in my car, like at a family camp trip when i show off lol. But i see your point, subs would roll off some by that point and most music that is Mastered correctly with "real" music doesnt dip below 25hz. Just thought id pick your brain on the subject. Thanks again, have a good one!
@arthurhughlett2292
13 күн бұрын
Is it possible to accomplish this through a factory head unit without db slope?
@DIYAudioGuy
10 күн бұрын
Yes, that is why there is a crossover on the amp.
@markmillan1294
2 ай бұрын
may i know what song is it? (00:35) pls and thanx
@sleepzzz800
4 жыл бұрын
The way you set crossover seems to be different from others. On other videos, people will play the frequency that they want their crossover set at, and whatever the voltage is when the frequency is playing, they will adjust the knob until voltage starts to drop and that’s where we would set it at.
@DIYAudioGuy
4 жыл бұрын
One of us has to be wrong.
@DIYAudioGuy
4 жыл бұрын
Take a look at what happens around 11:20. I turned the crossover on and I turned the knob all the way to the right. So the crossover is set to 500 Hertz. At that point the voltage is just slightly less than the starting voltage. So if you use the other method your crossover would be set to 500 hz, not 50. Those other videos have thousands of views. Which means there are thousands of people out there with crossovers that are off by an order of magnitude. You will notice that in this video I verified my math by comparing my predicted results against the result I got from the digital signal processor.
@jdipo16
4 жыл бұрын
The crossover frequency point is always -3dB. So setting to crossover to 80hz means that there will be a -3b or 30% reduction in voltage at 80hz. This video shows exactly that
@DIYAudioGuy
4 жыл бұрын
Crossovers can get pretty complicated. I'm not 100% sure that I have it right. But I've seen some KZitem videos, from larger channels that should know better, that absolutely have it wrong. Not trying to cast shade on them, just trying to help people.
@tedtan6449
3 жыл бұрын
Most amps have fixed slopes. The setting up for a target crossover, at an assumed frequency where the amp labelling is, could be inaccurate. If say one rotates the knob to a 90 hz lowpass, the only sure way to know IT has kicked in at the right frequency, is to start Sweeps and record the voltage where it changes. Burst tones are more accurate, at increments of one. There are audiophile test cds with these tones. The track number and test tone at certain frequency is given.
@dennycote6339
3 жыл бұрын
You set crossovers at full power. Can you also do this work at any given voltage? say 1v output so you can do it with speakers hooked up. doesnt the speakers impedance affect the voltage output of the amp?
@DIYAudioGuy
3 жыл бұрын
What I do now is I pick a lower voltage, and something that makes the math easy. So I'll adjust the head unit until I get something like 10 volts. There are some who suggest you should do these settings with the speakers connected I disagree because you run the risk of damaging your speakers by pumping test tones through them. Plus test zones are hell on your ears.
@user-ht2ct9gr3v
Ай бұрын
X-Over Filter Range: 40Hz-2KHz ?
@gd6315
8 ай бұрын
Bonjour je voulais vous poser une question comme le réglage du crossover modifie la tension je devrais régler le crossover avant le gain ? Merci pour votre retour
@TheLawlessGang
Жыл бұрын
how fo i set my lpf on a monoblock? im trying to set it to somewhere between 60-80hz
@EZCustomzz
5 ай бұрын
Just what i needed!! Thank you
@DIYAudioGuy
5 ай бұрын
Glad I could help!
@matt.246
3 жыл бұрын
What level does the volume need to be at if I already know where I'm clipping?
@DIYAudioGuy
3 жыл бұрын
You'll need something more advanced than a multimeter to know for sure. The 75% rule of thumb is just a rule of thumb, it works for most people and will get them close enough. Without more measuring and testing the only thing you can do is turn it up until it sounds bad then turn it back down a notch.
@BeatsByGRIMM
2 жыл бұрын
Saved me $180 .. Subscribed! Thanks!!
@DIYAudioGuy
2 жыл бұрын
Glad I could help!
@jaberwocky6669
7 ай бұрын
So, if I want an 80hz crossover frequency then if I take my unfiltered voltage and do the math then I will be down by x amount of DBs at that crossover frequency. So should I play a test tone that is one octave below my crossover point so that I will be at 0db until that point? (oops, meant below not above ... or wait, did I mean below????)
@abhichopra7217
3 жыл бұрын
Thanks mate really knowledgeable One thing I have got amplifier but no gain knobs only bass eq , LPF,HPF, Levels,crossover and subsonic So don’t no how to set the gain for subwoofer please
@DIYAudioGuy
3 жыл бұрын
The levels might be your gain knobs.
@DemonOfFury
10 ай бұрын
My amp has no shut offs and my high pass and low pass are both always on…. Gus’s I just have to use a processor to but how do I set these ?!?. Not sure how to do it with both active at the same time.
@DIYAudioGuy
10 ай бұрын
Start with the low pass on it's highest setting and the high-pass on it's lowest setting.
@jessesibley4001
5 ай бұрын
What app is that
@TRONMAGNUM2099
2 жыл бұрын
Ty it was always such a pain to guess where 80hz on the crossover is. I never understood why they have like 30hz and like 150hz on a crossover and no other marks.
@DIYAudioGuy
2 жыл бұрын
Glad I could help. Don't forget the most important thing. How does it sound? The math is just there to get you close. Let your ears do the rest.
@joes1214
3 жыл бұрын
Can I use the same principles for home audio? Let's say building a crossover, which I'm trying to avoid, but I'm using a couple crown xls 1000'swhich have the adjustable high pass,low pass built in ?
@DIYAudioGuy
3 жыл бұрын
Yes.
@rexnhogz
3 жыл бұрын
best crossover video on you tube!!!
@DIYAudioGuy
3 жыл бұрын
I like to think so! I have been doing some research on different crossover alignments and if I ever get them all figured out I will make an even better video!
@raymondchapman5990
4 ай бұрын
I'm confused......how is the DSP app on your phone changing the voltage on the amp ?
@DIYAudioGuy
4 ай бұрын
In this video I am testing the output to show how the DSP changes the amplifier's output voltage. In this case the DSP is there just to show that my math is correct. Then I change the crossover on the amplifier to change the amplifier's output voltage.
@LeroyMclovin
Ай бұрын
What should the settings be on your head unit when you do this?
@DIYAudioGuy
Ай бұрын
I like to set the volume knob so that I have 10 volts, that makes the math easier.
@LeroyMclovin
Ай бұрын
@@DIYAudioGuy What about subwoofer and bass setting. My Head unit has a separate subwoofer control. Ive heard some people say to turn the subwoofer setting all the way up and others say have it all the way down. Also I would assume to set the equalizers to "flat"? Thanks
@BasicKustoms
10 ай бұрын
When setting the Crossovers, Should your gain already be set?
@DIYAudioGuy
10 ай бұрын
Yes
@jahrocks
Жыл бұрын
Whats the calculation for high pass
@DIYAudioGuy
Жыл бұрын
It is the same.
@askiagillette
Жыл бұрын
Two questions. 1- If I set my low pass on my sub to 120HZ, then my 4 sets of components on the 4 channels high pass to 120Hz do I run the risk of canceling out in certain areas where the speakers won’t play sound? 2- if I want my rear 6x9s to act as my mid range and play a full/band pass so I can play between 120hz-500Hz how would I do this if setting the voltage for channels 3/4 would require tuning the same channel for proper cut off on the other end?
@DIYAudioGuy
Жыл бұрын
1) Yes, a 2nd order Linkwitz-Riley crossover will have a null at the crossover point. It is easy to fix just flip the polarity on the sub. If it sound better then keep it that way, if not then flip it back. 2) Set the voltage the same, you just need a bandpass crossover.
@toddpaugh5826
4 жыл бұрын
Does this formula work at any volume level? I assume the reference voltage is the voltage at whatever volume you are at.
@DIYAudioGuy
4 жыл бұрын
Yes, it does. What I've started to do lately is to set the volume so that the voltage is at a nice round number to make the math easy. If the starting voltage is 10 then all you have to do is move the decimal in order to do the math.
@johncoscia5258
Ай бұрын
The sound from my 3 way gets distortion so which speaker driver do i put a inductor or capacitor in series to help please ? Midrange seems to not be active enough since the adjustments allowed me to go 6db max higher than flat on my crossover but it that's all so is it just not enough db' from the midrange causing distortion ? Thanks
@DIYAudioGuy
Ай бұрын
Is it a three way component set with a crossover? Honestly not much you can do unless you plan to rebuild the crossover from the ground up. I would get a DSP and go active. lddy.no/1k6jq
@johncoscia5258
23 күн бұрын
@@DIYAudioGuy I purchased a low frequency DSL from Dayton and adjusted the db's curve of the midrange and the results in stereo are really impressive and educational .Boom gone, but plenty to learn Thank you .
@user-yg2xh3fh2y
Жыл бұрын
I am a little confused. on the spreadsheet you used 20volts as the unfiltered voltage and that 20 was used for the formulas in the calculations but then show 13v as the starting voltage. What is the difference between the 20v and the 13v? Is there as filter that is on that filters the 20 to 13? I am assuming there is. Thanks again.
@DIYAudioGuy
Жыл бұрын
The starting voltage is going to depend on where you have the volume set. What I have been doing lately is I have been turning the head unit up until I got 10 volts. That makes the math a whole lot easier.
@martyjr540
3 ай бұрын
My question is what and how do you find or get your unfiltered voltage to multiply by?.
@DIYAudioGuy
3 ай бұрын
I just probe the outputs with the multimeter. After I made a few of these video I figured out a trick. I adjust the head unit volume to get 10 volts out of the amp. That makes the math a lot easier.
@martyjr540
3 ай бұрын
@@DIYAudioGuy thanks, in the video you showed using 20 volts unfiltered to multiply by. Are those volt factors still applicable with a 10 volt output?. Thanks.
@DIYAudioGuy
3 ай бұрын
@@martyjr540 Yes.
@martyjr540
3 ай бұрын
@@DIYAudioGuy I will give it a try. Thank you.
@7saiin163
9 ай бұрын
lets say i played a 38hz test tone and adjusted the subsonic filter, then to set the lpf should i take the original unfiltered voltage i used for the subsonic and do the calculation or the “new” voltage and redo the calculation but with a 80hz for the lpf?
@DIYAudioGuy
9 ай бұрын
That is a great question, join us on our next live show and we will try to give a detailed answer: bit.ly/3PYKG5P
@jus1taj
3 жыл бұрын
That was really hard to follow. I can see your calculations are sound but I was confused as to which filter you were referring to. If you would, please consider redoing this vid but dumb it way down. Solid info just hard (for me) to follow. Thanks man!
@DIYAudioGuy
3 жыл бұрын
kzitem.info/news/bejne/w4SX24Ohs5aFhYI
@raygibson1295
3 жыл бұрын
Where can I find the Q multipliers? Is there a chart 📉 or something available?
@DIYAudioGuy
3 жыл бұрын
I don't have a chart, but you can just hit pause at about the 1:00 mark and take a screen shot. Here is the formula that I used to calculate them: 10^(-(slope)/2)/20)
@remonpeterson2652
Жыл бұрын
How to you reach on hpf 2000hz?? How do I get that frequency? Are the hpf numbers by 10? 😢😢
@DIYAudioGuy
Жыл бұрын
Sounds like you're trying to cross over a tweeter. Most amplifiers are not designed to do that. Some will have a 10x switch on them that will multiply the crossover by 10. Look for an amplifier that has that. All of the JP series 4 channel amplifiers have the 10x switch. Hit the down for sound link in the video description.
@dmcd2460
Жыл бұрын
I'm an old school installer MECP since '95. you really don't explain why your looking for a certain voltage output from the amp I'm sure it's clipping above that voltage? I used to use a hi fonics Callisto crossover which is still the biggest and probably the best crossover ever made. Now since I'm out of the game and not showing it trying to win trophies I just use the built in crossover in my pioneer head unit. It does the job without taking up space in my trunk. Now my sub amp does have a crossover and bass boost but I turn off the internal on the amp and use the highest slope from the HU. What exactly is bass boost doing? Just turning up a certain frequency or more like a parametric turning up a series of frequencies? Of course my HU Has lots of other settings. Including a 31 band eq on the pioneer app. My mid and components amp 6 channel has no built in crossover or processer but I do run the passive that came with the components. You do also kinda leave out how to adjust a mid bass driver in a band pass. My HU will allow me to do this internally and I usually just do it by speaker specs and by ear. Usually sounding the best at around 80hz up to about 3-4khz speakers are rated to play down to 50hz. Thanks for the vids but I need more explanation. I mean I haven't even heard you say to set your voltage meter to AC. The layman isn't gonna know that speakers work off AC and might not get a reading at all on DC and being that we are testing car audio might not realize this fact. I'm really not trying to be a smart butt, just pointing out critical things as a viewer that could help make your videos much better. So if you do something similar might want to mention to set your meter to AC for speaker output. Also maybe make a vid using HU crossover controls, because that's what a modern deck has and it's much more adjustable and accessable from the driver's seat. Also address multiple controls on multiple devices. That would be a great great help. Thanks again.
@DIYAudioGuy
Жыл бұрын
I think this might have been my second or third KZitem video. You raise some good points. If I can find the time I might redo it and add some more detail. I might need to break it down into two or three videos so that people don't get lost.
@daveroski
Жыл бұрын
Question: Does turning up volume make the voltage go up? Not sure what level to play the test tone?
@DIYAudioGuy
Жыл бұрын
Yes. I like to turn the volume up till I get about 10 volts. That makes the math really easy.
@1904audio
8 ай бұрын
I have a taramps bass 15 it has a high pass and low pass filter, because it's a amp for subs do I turn the high pass filter all the way up to block out higher frequencies? Basically how do I set these 2 controls to keep the pure sound of bass?
@DIYAudioGuy
8 ай бұрын
I'm going to take a screenshot of this and answer it on our live stream tonight because there are a ton of people with questions about that specific thing. You can tune in or you can watch the replay.
@dwaynebullock6297
4 жыл бұрын
Does this same trick work on high pass filter? Or low pass only?
@DIYAudioGuy
4 жыл бұрын
Yes.
@TylerStClair-mx7dj
3 жыл бұрын
And also would I set my gain to to the appropriate level with the low pass and subsonic open before I set the low pad and subsonic filter
@DIYAudioGuy
3 жыл бұрын
When you set the gains you want all of your crossovers off and any EQ settings set to zero or flat.
@joelpasserell4525
Жыл бұрын
If I'm using the crossover in the DSP I just set the AMP x-over to FULL and start in on setting the signal gain and don't have to do any of this, correct? Didn't you make a video on setting the amp signal gains accurately with a DMM? Can you link that here as well? Thanks.
@DIYAudioGuy
Жыл бұрын
Correct, and Yes. kzitem.info/news/bejne/rniZrYOli3xlhaQ
@angelludia6758
Жыл бұрын
Thanks
@EZCustomzz
5 ай бұрын
Question, does the bass knob at all affect the voltage setting in any way while setting crossovers. I know you said turn the volume you enough to get a read out.
@DIYAudioGuy
5 ай бұрын
kzitem.info/news/bejne/laF63omZgHWWa4Isi=mq7uMEWpYDC6p1mg The idea here is to use the DMM to look for a 3 or 6 db drop. When you run that through the db formula the starting point does not matter. Down 3 db from 10 volts and down 3 db from 20 volts is still down 3 db.
@ericfulmer2546
2 жыл бұрын
Didn’t work for me with an AudioControl LC-1.800.. No off and on Switch for Crossover. Set it to the highest point and played a 120 Hz test tone, and with the math, It ended up on the 80 Hz point of the amp..
@DIYAudioGuy
2 жыл бұрын
What crossover point were you shooting for?
@TylerStClair-mx7dj
3 жыл бұрын
So when I go to set my lpf my read output voltage is 50 volts. So I go to play an 80hz test tone and start turning from left to right my lpf to roughly 25 volts as I have a 12b/octave slope on my lpf and the lpf bottoms out at 36 volts?? What shall I do now!Help plz DIY Audio Guy
@DIYAudioGuy
3 жыл бұрын
That's odd, not sure what to tell you. It is hard to trouble shoot without having the equipment in front of me.
@mattfire8579
2 жыл бұрын
But what if you Want more bass from your HPF filters? I just use an O-scope and set my input volume (phone) and headunit to max with my equalizer settings preferred and adjust both gain and hpf until I'm in no clipping territory and have achieved as low of hz as I want. I don't know howto do it more detailed and down to the science despite watching a lot of videos and reading.
@DIYAudioGuy
2 жыл бұрын
If you are happy with the sound then you should be good.
@mattfire8579
2 жыл бұрын
@@DIYAudioGuy I really appreciate the response DIY Audio Guy. Really appreciate the content too. You are one of the guys I've been liking following closely on KZitem. Thank you for all the work your doing on us newer guys behalf and putting it out here for us! 💛
@streaxu
2 жыл бұрын
Say im using a DSP, do i need to set the crossovers on the amps too? If not, do i just set the switch on a 4ch to Full Range? And for the HPF/LPF knobs, where do i set them If they don't go to zero (both for sub and mids/high amps)
@DIYAudioGuy
2 жыл бұрын
No need for the crossovers on the amplifiers if you're doing it all with the DSP. Yes, If the crossover has an off switch, go ahead and turn them off. If you don't have an off switch, then set your low pass filters to the highest frequency, most of the time. This means turning it all the way to the right. Then set the high pass crossover to the lowest possible frequency, typically this means turning them all the way to the left.
@mrmister704
4 жыл бұрын
How do you set a gain and xover for tweeter @125rms and xover @6000hz? I can do this for 150hz, 50hz, etc but the multimeter isn’t reading the way i expected.
@DIYAudioGuy
4 жыл бұрын
Interesting, what is the multimeter doing? Most multimeters can read the frequency, try a 6,000 hz test tone and see if the multimeter can read the frequency.
@mrmister704
4 жыл бұрын
@@DIYAudioGuy yep I did and the voltage didn't read like a 150 tone, it read like 4.3 instead of 22.00
@DIYAudioGuy
4 жыл бұрын
I honestly don't know what to tell you.
@scorpion30001
2 жыл бұрын
How or what is the starting voltage? i just wane make sure.
@DIYAudioGuy
2 жыл бұрын
Any voltage will do. I recommend but you pick one to make the math easy, like say 10 volts.
@robertholsopple9451
2 жыл бұрын
what if the slope is variable as is in the case of skar 800.1d
@DIYAudioGuy
2 жыл бұрын
Then pick the slope you want to use and do roughly the same thing.
@booboo1ed
3 жыл бұрын
I have a Skar audio 1500.1D mono running 2 12’ kickers L7q at 0.5 ohz im still trying to figure out the amp settings please help i want it to hit. Fyi running a stock radio
@DIYAudioGuy
3 жыл бұрын
It is difficult to trouble shoot over the internet. I have several videos on setting up an amp. Have you seen this one? kzitem.info/news/bejne/0HiEq4iocnN5qnY
@elsadatjakupi2832
3 жыл бұрын
Hi do you have a different site for more detailed correspondence? I’m starting a project but have quickly realized I may be in over my head a bit but I want to learn so I want to do it myself. You might be able to help with some more detailed question answers.
@DIYAudioGuy
3 жыл бұрын
You can email me DIYaudioguy@gmail.com.
@JoshM7
3 жыл бұрын
I was thinking I'd set my highpass today for my car sub. However I'm a little confused on the "Cut at X-Over Frequency" Using some software crossover (WinISD for example) using a 20Hz Butterworth Highpass the -3dB point is always going to be 20Hz regardless of the slope/order. So either I'm confused and missing the point or something lol. It doesn't seem to change at all with the Q setting. So maybe just a limitation of the program or it's functioning as intended. Which means in my case my 2nd order (12dB/octave) highpass in my car should be set using your 0.708 Voltage Factor graph. Technically any Butterworth should be set that way it seems. Correct me if I'm wrong in assuming this.
@DIYAudioGuy
3 жыл бұрын
I don't think you are wrong, as I have done some more research I think the DSP I used in this video to "verify" my math may be implementing it wrong.
@ravensix4290
Жыл бұрын
Whats the app you are using
@DIYAudioGuy
Жыл бұрын
It is the DSP app that came with the DSP.
@TylerStClair-mx7dj
3 жыл бұрын
Can I apply this same method and math to set my subsonic filter at 30hz?
@DIYAudioGuy
3 жыл бұрын
Yes! kzitem.info/news/bejne/yo2I1X2eqGlyapg
@brunom1280
2 жыл бұрын
How do I calculate voltage factor for my amps? I may have missed this step in video
@DIYAudioGuy
2 жыл бұрын
I don't show the calculations in the video, I just show the results in the video. The formula used for the calculation can be found here: kzitem.info/news/bejne/laF63omZgHWWa4I
@brunom1280
2 жыл бұрын
@@DIYAudioGuy thank you il give it a go
@E-raticWarrior
Жыл бұрын
Glad i found you, but i only have one question. How did you come up with the voltage factor?
@DIYAudioGuy
Жыл бұрын
It's based on the DB formula that I explained in this video kzitem.info/news/bejne/laF63omZgHWWa4I
@E-raticWarrior
Жыл бұрын
@@DIYAudioGuy Thank you sir.
@cgbcody
2 жыл бұрын
I really appreciate your videos, I'm not sure what I am doing wrong, but I have a 1200.1d amp, 24/oct variable amp, 32hz tuned ported box. Does it matter if I set LPF or SS first? I tried both, but am unable to get the HPF down to 2.51, It will only go to 5 dropped to the lowest. 24 hz tone for SS and 80 for HPF. Thank you for your videos.
@DIYAudioGuy
2 жыл бұрын
It's really hard to say without being there to troubleshoot the amp. But you probably should be okay, a 24 DB slope is very steep so you can get away with setting it as slightly higher frequency. Main thing is to take it easy with the volume knob until you're certain that you're not unloading a little frequencies.
@saintckk
Жыл бұрын
new to your channel, a newbie question. if my head unit come with crossover function for the front speaker, can I set my 4 channels Kicker amp to "Full"? Moreover my front speakers also came with a pair of passive crossover! is it good enough for preventing blowing my system? thanks
@DIYAudioGuy
Жыл бұрын
Yes. I prefer the crossover on the head unit since it is easer to set -- no multimeter needed. I would need to know more about your passive crossover to give you a complete answer, there are several ways that those can be configured. If you are running a two -way component set then crossover will protect the tweeter and the crossover on the head unit will keep the low bass out of the midrange driver.
@monstah408
Жыл бұрын
Hello , awesome video , just having a brain fart , when I set my gains on my sub amp , the LP filter should be at its lowest setting , then when I set the crossover turn to highest setting , get my target voltage around 10v multiply by my amps 12db slope at .501 then turn down until I get 5.01 volts correct?
@DIYAudioGuy
Жыл бұрын
Think of the crossover as a choke (some people even use that term for an inductor in a passive crossover) on a carburetor it limits the airflow into the engine. Step one is to turn off the choke or open it up as much as possible. For a low pass filter the lowest setting is full choke, nothing gets through. For a high pass filter the highest setting is full choke, nothing gets threw. You want to open it up. Set the gain and leave it open. Then use the instructions in this video to set the crossover to your exact desired position.
@monstah408
Жыл бұрын
@@DIYAudioGuy awesome thank you very much !
@aqua21
3 жыл бұрын
Sorry for my poor english but I have an question for you. I followed this video tutorial yesterday when I tweaked an 4x80w 4 ohm´s amplifier (GAS 80,4 Pro) with a crossover. The strange things where that the output voltage did not change at all when I switshed between HPF and Full range. I could see a minor difference when I screwed the wheel but it was way under 1 volt. I had an unfiltered voltage of around 10,05v and it was almost the same when I swithed to HPF. If I connected the speakers I could hear the difference in sound so it seemed that the filter worked correctly. I suppose I did something wrong, I also tried to use an oscilloscope on the speaker outputs both on the 4x80w 4ohm amplifier (1000hz -5db test tone) and the 1000w GAS 1.1000 PRO 1-4 ohm (40hz -5db testtone) to get the correct gain but the curves on the ocilloscope looked distorded way under the max output that those amplifier should have left. For example the 1000w amplifier had a clean signal only up to 17v. The head unit where correctly tweaked with the oscilloscope and the volume where set to that maximum level. In the end I just put the voltage at 17,8v at the 80.4 amplifier and 34.6v (600w 2ohm) at the 1.1000 amplifier and it sounds just fine in my opinion but it was really annoying that I could'nt do it the way that i had planned from the beginning. The HPF screw where just put around where I thought 80hz where.
@DIYAudioGuy
3 жыл бұрын
I am sorry it did not work. It is very difficult to trouble-shoot in KZitem comments. If it sounds good to you then it should be fine.
@jasonshahid2929
3 жыл бұрын
Would I set my gain first and then do the crossover after?
@DIYAudioGuy
3 жыл бұрын
Yes
@Petrolhead66
2 жыл бұрын
I am setting up the Alpine mono 500w amp (31.62V) you have in your gain setup vid (..My sub can rated to 200w so I juices it to 240w, so thats 22v. I assume when you start the LPF your still playing to same 40/50 htz test tone at 75% vol. The Alpine amp is 24db Octave and therefore the voltage should be 5.59v. Does that sound correct
@DIYAudioGuy
2 жыл бұрын
You want to play a tone that equals your desired crossover frequency. kzitem.info/news/bejne/w4SX24Ohs5aFhYI
@mcfriedchicken1972
3 жыл бұрын
how do you know what test tune to use for the unfiltered voltage?
@DIYAudioGuy
3 жыл бұрын
If you're trying to set the crossover at 80 Hertz then play in 80 Hertz test tone.
@mcfriedchicken1972
3 жыл бұрын
@@DIYAudioGuy ok so that's generally for subwoofer, correct? And what frequency should I play for full range speakers? These are probably dumb questions but I'm fairly new to all this.
@DIYAudioGuy
3 жыл бұрын
@@mcfriedchicken1972 1,000hz. There are no dumb questions.
@DIYAudioGuy
3 жыл бұрын
Hang on, I Just give you a terrible answer. Ithought you were asking a question on a different video. If you're trying to set the high pass on an amplifier for some coaxials or a set of components then you would also use 80 hertz. 80 hertz is kind of a standard starting point for crossovers.
@kurtmccormick1730
2 жыл бұрын
how do we find out how many db per octave our amp is?
@DIYAudioGuy
2 жыл бұрын
Should be in the manual.
@thatizzy24
Жыл бұрын
On my pdx-1.1000 alphine amp the db/oct slope shows as a negative numbers and not a positive like this -> (-24dB/oct) would I use the positive 24 voltage factor ?
@DIYAudioGuy
Жыл бұрын
Yes, the negative sign just indicates that it's cutting by 24 DB per octave.
@thatizzy24
Жыл бұрын
@@DIYAudioGuy Thank youuu for always getting back with my questions , I really appreciate it 👍🏽
@bpintogsxr1000
3 жыл бұрын
Awesome video
@DIYAudioGuy
3 жыл бұрын
Thanks!
@bmckim5
3 жыл бұрын
How would you do this if using the head units lpf?
@DIYAudioGuy
3 жыл бұрын
Most head units will let you choose the frequency. So just pick the one you want to go with.
@ericnesbitt4758
3 жыл бұрын
What if you don't have a DSP is it still possible to do
@DIYAudioGuy
3 жыл бұрын
I just used The DSP to verify that my math was correct.
@tonydize3944
Жыл бұрын
I'm a big fan of your videos but i have a question my amp says -12db could you explain me the difference please thank you for all you do
@DIYAudioGuy
Жыл бұрын
Not sure. What amp is it?
@tonydize3944
Жыл бұрын
@@DIYAudioGuy taramps smart 5k bass thank you very much for replying most people never do
@DIYAudioGuy
Жыл бұрын
@@tonydize3944 I don't have any experience with that brand, so I can't say for sure. My best guess is that it's a bass boost and the - 12 is off. If you tried searching online for an owner's manual?
@tonydize3944
Жыл бұрын
@@DIYAudioGuy thank you again friend you're always replying to your followers i see all the comments I watch your videos every day just to learn more in fact i was watching them right now keep up the great work you do 👏🏻
@paulgood2218
2 жыл бұрын
Love the videos
@DIYAudioGuy
2 жыл бұрын
Thanks!
@mopar392ta3
4 жыл бұрын
Is the volume all the way up before clipping?
@DIYAudioGuy
4 жыл бұрын
You don't need the volume all the way up when setting crossovers. It's just a matter of comparing the voltage before and after. I show how to check for clipping in this video: kzitem.info/news/bejne/rWaQvqVonqFegoI
@mopar392ta3
4 жыл бұрын
DIY Audio Guy ty sir. Getting ready to do a install in my 300 as soon as my package comes in
@giltyal5912
Жыл бұрын
So if my sub amp has a 12db slope and I want my cutoff frequency to be 30hz...would I multiply 30×.501? And set my voltage accordingly?
@DIYAudioGuy
Жыл бұрын
Correct.
@giltyal5912
Жыл бұрын
Thank you for your time!
@KGReef
3 жыл бұрын
Is the multiplying factor always the same for each slope type? Or does that need to be calculated depending on different factors?
@DIYAudioGuy
3 жыл бұрын
It's different for each slope.
@KGReef
3 жыл бұрын
@@DIYAudioGuy the voltage factors are as shown? So for future reference if I were to do the math. A 6db per octave slope will always have a voltage factor of 0.708?
@DIYAudioGuy
3 жыл бұрын
Yes!
@KGReef
3 жыл бұрын
@@DIYAudioGuy ok, thanks! Isn't math fun? Lol
@DIYAudioGuy
3 жыл бұрын
I think so.
@eustacefulford6159
3 жыл бұрын
what value level should be set at when doing this ?
@DIYAudioGuy
3 жыл бұрын
It does not really matter. But It is best practice to set your gains properly before you set the crossovers. I always like tinker with the volume on the radio until I get a good round number for the first reading. This just makes the math easier. These videos may help: kzitem.info/news/bejne/rniZrYOli3xlhaQ kzitem.info/news/bejne/yo2I1X2eqGlyapg
@abcdefghij2099
2 жыл бұрын
Does the DMM have to be true RMS for this to work?
@DIYAudioGuy
2 жыл бұрын
Yes! BUT! Oscilloscopes have gotten so cheap lately that I would just skip this and grab an O-scope. kzitem.info/news/bejne/0HiEq4iocnN5qnY
@mohavved
2 жыл бұрын
Great video DIY Audio Guy. i watch a lot of videos i'm still cunfused to set crossover sittings how i can know the slope or OCT for my amp? i dont found any information from anywhere
@DIYAudioGuy
2 жыл бұрын
The crossover slope should be in the manual, if you can't find a manual online, I can't help you much. You can just assume that it's a 12 DB per octave slope and go with it.
@mohavved
2 жыл бұрын
@@DIYAudioGuy i send you a message in instagram please check
@DIYAudioGuy
2 жыл бұрын
@@mohavved I'm not seeing your message in Instagram. Feel free to ask your question here, I'll try my best to answer it
@mohavved
2 жыл бұрын
@@DIYAudioGuy i send you some pic for my amp to help my username is @9.3
@adam_1dizon121
4 жыл бұрын
Great video very informative.. I have a question. do u do this crossover settings after setting your gain with a 40 or 50 hertz tone?
@DIYAudioGuy
4 жыл бұрын
Yes, set the gain first.
@acmilanshevachels
4 жыл бұрын
@@DIYAudioGuy Greetings! To follow up on your reply. In my case, it was not possible to set the gain first. I had to do the LPF and HPF (subsonic) tunings. Reason I couldn't do my gain first was because I could not reach my "required" 31.6V for the 1000W for my sub. The minimum reading on the DMM was 32.0+ V on the absolute lowest gain setting. Only after once I set the crossover points on the LPF and HPF first, did my gain gain knob actually give sensible voltage values. Does this seem correct to you? Does it actually make a difference which you tune first? Thank you! edit: my sub level on the headunit was to 0.
@DIYAudioGuy
4 жыл бұрын
Sounds like it worked out fine for you. What frequency test tone did you use to set the gain and what is your crossover frequency?
@acmilanshevachels
4 жыл бұрын
@@DIYAudioGuy First I set the subsonic filter by playing a 30Hz 0dB tone. Then I set the LPF by playing a 80Hz 0dB tone. Finally I adjusted the amplifier's gain knob (headunit was 85% of max volume) by playing a 40Hz -3dB tone to bring it to the ~31.6V. Anything that jumps at you that you would do differently? Thanks!
@DIYAudioGuy
4 жыл бұрын
@@acmilanshevachels If you are happy with the sound and you are not clipping, then it is good.
Пікірлер: 412