🔗 / mrd_rc 🔗 www.MrD-RC.com
In this video, we set up the SRx receivers in ETHOS. Though if you use OpenTX or EdgeTX, a lot crosses over. I cover the quick mode, which gives you manual, stabilised, and self levelling modes. Plus a gain knob, to dial the stabilisation strength, and an Oh crap switch, to automatically level the model. I also cover how to reverse the channels if the stabilisation is not going the correct way. Plus, how to change the pin outputs on the SR10 Pro, so that you can still use all 10 sets of PWM outputs.
NOTE: In this video, I get the stabilisation of the rudder backwards. The rudder should move in the same direction as the tail of the plane moves. So the opposite direction to the nose.
✈️ Contents ✈️
00:00 Introduction
01:03 What I'm using for the demo
01:28 Creating a standard model
02:09 Registering and binding the SR receiver
04:06 Calibrating the SR receiver
06:46 How I have the receiver connected to the plane
07:20 Creating the mixes
07:30 - Creating the gain mix and adding the curve so that the whole pot range works
09:15 - Creating the modes mix
10:06 - Creating the self-test / oh crap mix
11:12 Checking and correcting the stabilisation
14:26 Setting channels to be auxiliary, not second ailerons or elevators
14:43 Enabling Quick mode (what I'm using in this demo)
15:07 Stabilisation gains and where to adjust the self levelling
16:07 Correcting the control surface movements when moving the gimbals
17:12 Performing a self check
18:38 What can cause self check to not work, and how to fix them
20:16 Overview of the stabilisation modes
20:38 How to reverse the mode switch
21:00 Demo of the oh crap mode working
21:37 Adding a momentary switch to operate the oh crap mode
22:54 Getting all 10 pin sets working on the SR10 Pro receiver
26:25 Conclusion
Thank you for watching this video. Time is precious, so I hope that you got some benefit from this video. If you have any questions, please leave a comment and I'll do my best to answer. Please try to keep questions relevant to the video in, as they may also help others who have the same question.
✈️ In this video ✈️
⚙️ FrSky Tandem X20S transmitter: bit.ly/MrD_3x6...
⚙️ FrSky Archer SR10 Pro receiver: bit.ly/MrD_3DF...
✈️ Help other RC pilots find this video ✈️
If you found the video useful, I'd appreciate a thumbs up. This will help KZitem share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.
✈️ Supporting me and other resources ✈️
🛩 There are more tutorials on my web site at www.MrD-RC.com.
🛩 You can also join like-minded people at the Fixed Wing RC Rebels group and INAV Fixed Wing Group on Facebook.
🛩 Join the channel's discord server at / discord
🛩 Liking the video, subscribing, and clicking the bell icon can help greatly. This shows KZitem that the video is helpful, so it will be shown to more people, who may have the problem dealt with here.
🛩 If you found my video useful, you can become a Patreon at / mrd_rc
🛩 If you prefer, you could always buy me a Coffee at www.mrd-rc.com...
🛩 I also have merch at mrd-rc.creator... This include branded items as well as general fixed wing RC apparel.
Thank you for your time, and don't forget to fly it like you stole it!
Негізгі бет Setting up FrSky Archer SRx stabilised Receivers
No video
Пікірлер: 390