For more videos on Digital Electronics, check this playlist: bit.ly/31gBwMa
@shanifvn1080
2 жыл бұрын
Could you do a session on counters? Your videos are so helpful ☺️
@ALLABOUTELECTRONICS
2 жыл бұрын
Yes, it will also be covered soon.
@dahiwadaenthusiast
13 күн бұрын
Thanks, this was asked in an AMD interview on campus !!! God bless you thanks
@johnbrick7030
Жыл бұрын
would be nice if you could explain the hold and setup times more instead of just repeating the same thing about the delay, which is honestly pretty self explanatory
@mayurshah9131
2 жыл бұрын
THANKS FOR SUCH A WONDERFUL VEDIO
@seemakumar7232
Жыл бұрын
Explained very efficiently
@손주영-u9p
6 ай бұрын
I love you You are the BEST
@walenco
6 ай бұрын
Really thank you, it helps me very much,
@MinUyen3e92
4 ай бұрын
wonderful :D I understood some problems very useful
@b.j-allinone7984
2 жыл бұрын
Thanks sir
@souravdas9255
2 жыл бұрын
Please make detail video on MCU & MPU and Memory (DDR1-4 & Flash) and Ethernet
@ALLABOUTELECTRONICS
2 жыл бұрын
I have already made video about SRAM, DRAM and different memories. Please go through technology playlist on the channel. You will find it. In case, if you didn't get, let me know here. I will send you a link.
@poojapawar8162
2 жыл бұрын
Thank you
@nishikant_hota
2 жыл бұрын
Make video on BCA questions solving
@ALLABOUTELECTRONICS
2 жыл бұрын
There is already a seperate channel for Quiz. Please check the second channel ALL ABOUT ELECTRONICS - QUIZ.
@shilpapatel793
2 жыл бұрын
Very nice 👌👌👌
@spossiblehai8510
2 жыл бұрын
What is sampled you mean the read and write....
@ALLABOUTELECTRONICS
2 жыл бұрын
Yes, the Flip-Flop reads the input at the clock edge.
@TRUELiGHTERS
Жыл бұрын
setup time is how much before of the arrival of the clock edge ?
@SLUGTHUG
Жыл бұрын
That information would be specified by the data sheet of the device.
@MITHILESHKUMAR-iy2ci
Жыл бұрын
If TPLH and TPHL delay are different for a waveform, then what will be the actual delay?
@ALLABOUTELECTRONICS
Жыл бұрын
If both are different then generally the average of both delay is considered.
@saiprasadreddy2138
2 жыл бұрын
Even there Will be a clock delay for first and second flop right??
@ALLABOUTELECTRONICS
2 жыл бұрын
Yes, a clock skew.
@soumikdutta6171
Жыл бұрын
@15:00 why are you not considering the Hold times that are given?
@ALLABOUTELECTRONICS
Жыл бұрын
It is not required for the calculation of maximum clock frequency. I have already covered it from 6:10 onwards. The only thing which we need to check is, there should not be hold time violation. In this case it is not happening. Because the propagation delay from FF1 to FF2 is 7ns, while the hold time of FF2 is 3ns. That means Tpd > Th. Similarly, the propagation delay from FF2 to FF1 is 8ns, while the hold time of FF1 is 1ns. So, once again there is no hold time violation. I hope, it will clear your doubt.
@kheesang
Жыл бұрын
Hi Sir, In your last example , why didnt you consider Th into your calculation at all?
@ALLABOUTELECTRONICS
Жыл бұрын
In this case, if you see the propagation delay of the flip-flops or even the logic gates (2ns + 2 ns), it is more than hold time. That means there won't be any hold time violation in any flip-flop. And as I said in the video, for the calculation of minimum required clock frequency, we do not need hold time. Just we need to ensure that there is no Hold-Time violation. Please check at 11:20.
@kheesang
Жыл бұрын
@@ALLABOUTELECTRONICS Thanks sir
@willsalazarramirez5139
2 жыл бұрын
CHICLAYO PERU 🇵🇪 💵 🔱
@KandhanM-n1o
5 ай бұрын
14:09 in starting first case u are considering only propagation delay of the first flip flop why didnt you consider the setup time in starting but after one reputation u r considering the setup time of the first flip flop
@ALLABOUTELECTRONICS
5 ай бұрын
At first, we were calculating the minimum required clock for the second flip-flop. So, in that case there is no need to consider the setup time of the first flip-flop. In that case, we have considered to total propagation delay from the FF1 to FF2 plus the setup time of FF2. In the second case, when we are calculating the minimum required clock for FF1, then the setup time of first flipflop is considered. Please check that example once again, you will get it. And if you still have any doubt then let me know here.
@kollasivaramakrishna6732
10 ай бұрын
greaaattttttt
@AnonymousUser17059
2 жыл бұрын
This lecture is difficult to understand for me. May be of new terms, words 🤔🤔
@govardhan8962
Жыл бұрын
i will send problem to you ,can you give solution for the problem ?
@dreamy4174
Жыл бұрын
Nai samaj me araha😭
@micahgodsey455
10 ай бұрын
Thank you for the video, but your inflection on the ends of the sentence where you bring your voice up and then pause to monotonously say the last word is very distracting. Please just use your normal voice. I mean no offense or anything, and I know English isnt your first language. Thank you again!!
Пікірлер: 38