Level up your Icom IC-7300 here 👉kzitem.info/door/PLSuX83ay4OujxQFBseO9-dQCY6NOdBwXt Improve Your Icom's Waterfall 👉 kzitem.info/news/bejne/sYp6uXpqnoueZX4
@timkeene2717
2 ай бұрын
Hey Thanks much Mate for this video. I just won my ic-7300 in a raffle at a local tailgate swap meet. Not bad for $20. I never would have got this rig running so quickly without your help. Thanks again. Tim - K5DEZ
@HamRadioDX
2 ай бұрын
Nice work and congrats!
@regularguy519
Жыл бұрын
First post! Thank you for this video, starting to learn digital modes this weekend. 🎉
@HamRadioDX
Жыл бұрын
Awesome! Plenty of enjoyment and contacts to be made. Update your progress here and if you have any questions
@DonzLockz
Жыл бұрын
Good instructive video mate. I'm still deciding but I've saved this either way. I'm keen on digital modes and I'm glad you made this for us newbies. ;)
@HamRadioDX
Жыл бұрын
No worries hope it helps!
@jameyevans29
Жыл бұрын
This is just what I needed. Thank you!
@HamRadioDX
Жыл бұрын
Glad it was helpful!
@hthring
10 ай бұрын
Thanks for this ! Its working !
@rayharkins9564
5 ай бұрын
Thank you so much. You da man
@temporarilyoffline
Жыл бұрын
And that's how you do that!
@Soupie62
Ай бұрын
Well, that SORT OF worked. "Error in sound input" messages, all over the place. From reading elsewhere, need to put a few toroid chokes on my USB cable.
@manoffaith2501
Жыл бұрын
Doesn’t the IC-7300 have a FT8 Preset on page 2 of the menu?
@donwegeng5463
5 ай бұрын
This is a great video, however it does not address how to set the Windows audio level for transmitting. Is this covered in a different video?
@HamRadioDX
5 ай бұрын
Maybe here - kzitem.info/news/bejne/uq-NvmSfcWmBY6Q
@axi6ne8us
3 ай бұрын
Can those same settings be used for the IC-705?
@HamRadioDX
3 ай бұрын
Very similar, except just select the IC-705 from the drop down radios list
@joelaut12
Жыл бұрын
could you do. yeasu FT-450D also?? Great video!
@HamRadioDX
Жыл бұрын
I don’t own a FT-450D unfortunately. Great little radio though!
@davidcottee2808
Жыл бұрын
Finally got my IC-7000 working on FT8/WSPR. Unlike the 7300 I can’t turn off the microphone while transmitting. Just have to be quiet. As an aside, do you know of an ACARS decoder I could use with audio input rather than SDR. They all seem to have lost that feature in recent updates. 6 meters was open to Japan on Sunday afternoon BTW!
@jamesknotts1546
5 ай бұрын
Unhook your microphone?
@VFRRiderFT
Жыл бұрын
Sorry, I have a question on the initial settings, I have already set up my 7300 for use with the RS-BA1 Remote Utility and for that I have had to set the CI-V USB Port to Unlink from [REMOTE], so the question is can I leave it like this or should I change it?
@HamRadioDX
Жыл бұрын
Yes you can leave it like that, just set your baud rate in WSJT-X to whatever it is below that setting - probably 115300bps?
@Aussie_Ham_Radio
10 ай бұрын
Great video Hayden. The only addition I would make is on windows go into advanced and make sure enhanced audio is turned off. This allows a cleaner signal from the WSJT-X program to the radio. I did a video where in windows 11 you think you have turned it off but the windows 10 interface still shows it turned on. kzitem.info/news/bejne/zbCqvHqbq2d5pII
@HamRadioDX
10 ай бұрын
Great tip Glenn!
@robert-t3j6f
11 ай бұрын
HELP ANYONE .....my screen of wsjt-x is exactly like yours... except under "WSJT-X VERSION 2.61 K1JT ETAL" IT DOES NOT read "file config view mode decode save tools help" so i cant click on file to adjust the settings???? NS9T
@maxzdev
10 ай бұрын
What power supply are you using??
@HamRadioDX
10 ай бұрын
25A linear supply from Powertech
@exploreit3548
11 ай бұрын
Drivers for Linux ?
@bkdexter79
11 ай бұрын
Why did you omit the cabling required to set all this up? Where it goes, which cable goes where, etc. Yes... beginners need this! Also the website to download the software isn't available here in the states. Unfortunately this video seems pointless since you skip so much info.
@HamRadioDX
11 ай бұрын
Oh well can’t please everyone then 🤷♂️
@ohaya1
11 ай бұрын
Setting WSJT-X to Data/Pkt instead of SSB hides other people's signals in the software's watefall. Has anyone noticed it or is it just on my end? If it's true why does that happen?
@HamRadioDX
11 ай бұрын
Check your filter widths when you switch to the data mode. If it's too narrow it will hide some of the signals
@ohaya1
11 ай бұрын
@@HamRadioDX Thanks Hayden will try that
@rjschneid47
10 ай бұрын
You lost me when you went into audio and suddenly an audio menu appears on your screen and the viewer has no idea where it came from. Most users are faced with fixing the computer interface or installing one every so often, like 6-12 months, and there is no way that we are facile in jumping in and out of driver set-ups, device manager, and wondering where the audio menu is. I also noted that a number of my com port drivers were set at 9600 baud. Should they match the settings you had us put into the radio? Back to experimentation. 73, AB0CD..
@HamRadioDX
10 ай бұрын
Here is another video to assist - Get Started with FT8 - An Introduction for Beginners | WSJT-X Ham Radio kzitem.info/news/bejne/uq-NvmSfcWmBY6Q
Пікірлер: 37