Hey thanks for making this video. I’m rebuilding my engine hoping it’ll run again and had question about that stiff feeling at the top of the crank after you put the sleeve in. You explained it perfectly and confirmed it was ok, so honestly and truly thank you lol
@thebug4046
3 жыл бұрын
No problem glad it helped! I do have a Facebook group nitro/diesel/gas rc and more if you want to check it out 2 questions and your in
@coreyterhaar633
3 жыл бұрын
Might dig around for it once I get a car going...motor is a red headed step child I ordered one off eBay to have this one to repair one day maybe 🤷🏼♂️ Shoutout to the SDK sticker as well, I’m in BC Cheers
@thebug4046
3 жыл бұрын
@@coreyterhaar633 hell yeah! SURREY!
@coreyterhaar633
3 жыл бұрын
Thats rad 🤙🏼 If your interested in using my GXR18 for a teardown and rebuild video lemme know cause I’d love to have a spare runner and surrey isn’t that far to mail 🤙🏼 Cheers either way!
@thebug4046
3 жыл бұрын
@@coreyterhaar633 will let you know man thanks for watchin!
@kalpitoriLampung
3 жыл бұрын
Nice kawan Terima kasih atas infonya, salam dari Indonesia lampung🍉🍏
@Saddletramp1200
5 жыл бұрын
Hi, I am still watching. Leaning more into the bikes. Good Vid. And I can't understand a hundred bucks for a damn piston. That's just greed.
@АлексейЛ-ф5я
Жыл бұрын
Очень хорошо. Нашел в видео ответ на свой вопрос.
@thebug4046
Жыл бұрын
пожалуйста 🍻
@MMKnight_1
5 ай бұрын
Where did you find the parts for your engine? I have the same engine and I can't seem to find spare parts from a reliable site
@thebug4046
5 ай бұрын
Amain hobby usually has SH parts and same with eBay. I know they are trying to restock
@EvergreenComics
5 жыл бұрын
Your Commentary is fucking funny hahaha!
@Mrbinh-mn4hd
5 жыл бұрын
great video
@thebug4046
5 жыл бұрын
Thanks man! I have a handful of rebuild videos
@eliasbeas3556
3 жыл бұрын
Hey man, awesome video! I learn so much from your videos because I use alot of SH engines myself. Quick question, I have a brand new SH .18. The other day I tried tearing it down but had a really hard time removing the piston and rod. In fact, I have a werks b6 engine that does the same when I try to remove the piston and rod. Super frustrating. Any suggestions?
@monoganie7882
3 жыл бұрын
the piston/crank/connection rod/ need to be (or almost) in top dead center to get it out, of course after that the sleeve is already out,
@thebug4046
Жыл бұрын
Yeah they can be kind of frustrating sometimes depending on how they were machined but the engine that you have I have no experience with to be honest with you.
@christopherduggan7857
3 жыл бұрын
Will 3 in1 oil be ok for this .love your videos
@thebug4046
3 жыл бұрын
Yup will be fine you can use just normal synthetic engine oil to if you want
@pcrashford5367
4 жыл бұрын
What will be the main symptoms of worn out piston and sleeve (Once that will need to be replaced) ?
@thebug4046
4 жыл бұрын
Difficult starting poor compression and and and Jeanette shuts off when it warms up and will not restart until it's cool off completely and very short run times in between that
@gonzo2779
8 күн бұрын
In my case, the piston and sleeve wore down due to bearing failure, the engine ran good when cold but it heated up very quickly and reached 160 °c when the max normal temperature is 90°c. I got the piston and cilynder replacement kit and I'm about to put it together. OS 65 Ax
@hunterdurst4571
2 жыл бұрын
Can you run the traxxas .15 exhaust header with the SH.18 exhaust port looks the same as the .15
@thebug4046
2 жыл бұрын
Sure can! Same same!
@hunterdurst4571
2 жыл бұрын
@@thebug4046 haha sweet, getting a parts list together gonna give my Traxxas Nitro Sport a complete refresh, the pro.15 that’s in it now is soon do for a rebuild, going to buy another nitro sport roller and put it in it, I watched your videos on the pro.15 rebuilds, very very good explanation and details in the videos how to do so, that’s how I learned to rebuild nitro motors from your videos, I plan on buying another Nitro Sport to the pro.15 in. The Nitro Sport I have now is getting a new matte black body and the SH.18 with the black cooling head, going with a murded out look with this thing gonna look wicked lol. Thanks again for the help, I greatly appreciate it!!!!!!!!
@thebug4046
2 жыл бұрын
@@hunterdurst4571 your very welcome! Glad I could help ya! And the SH 18 doesn't come with a glow plug! OS 7 is what you want! Also they do have a upgrade ABC piston and sleeve available to! And if you go with a full aluminum exhaust they pull hard! Feel free to join my rc group on Facebook Nitro/Diesel/gas rc and more. I'm the owner post up your stuff ask questions it's a good group no BS! See you in there!
@hunterdurst4571
2 жыл бұрын
@@thebug4046 awesome man, I’ll post my Nitro Sport when it’s all finished.
@thebug4046
2 жыл бұрын
@@hunterdurst4571 definitely man looking forward to it 👌
@aaronwhite2160
3 жыл бұрын
U got link for one mate on eBay also will it work in a 18 engine for atorro
@thebug4046
2 жыл бұрын
Unfortunately not as they are out of stock at the moment
@smartguyonan9972
2 жыл бұрын
Saya beli itu mesin hsp mau beli minyak metanol di indonesia susah jadi saya pake bensin all hasil mesin bunyi kencang namun gak mengandung polumas jadi all hasil rusak mentalnya namun saya ganti ternyata nyala lgi mesinya salam hobi mesin👍👍👍👍
@thebug4046
2 жыл бұрын
Hey sorry I don't mean to be rude but I don't understand
@smartguyonan9972
2 жыл бұрын
I bought the machine but in Indonesia it's hard to get methanol oil
@smartguyonan9972
2 жыл бұрын
l bought an HSP engine, I want to buy methanol, it's difficult in Indonesia, so I use gasoline, all the engine sounds are loud but don't contain lubricant, so all the engine results are mentally damaged, but I replaced the engine, the engine turned on again, greetings to the HSP Buggi engine.
@thebug4046
2 жыл бұрын
@@smartguyonan9972 gasoline won't work and it will destroy the engine very quickly you have to add castor oil to the fuel. Try using ethanol and castor oil
@smartguyonan9972
2 жыл бұрын
okay bro I'll try later greetings engine hobby
@andrewdenine1685
4 жыл бұрын
My traxxas has the oil hole in the top and bottom of the rid
@thebug4046
4 жыл бұрын
If its the old style rod the whole will be at the very tip of the rod the new one has it underneath the Top pin board with very little meat there they are very prone to breaking
@codymiller5335
3 жыл бұрын
Can anyone tell me how to get flywheel spacer off
@thebug4046
3 жыл бұрын
A fine flat screw driver put in the slit and pull forward
@Silent47
3 жыл бұрын
How would you remove the sleeve from the carnkcase if you do not have the conrod and piston? I've tried freezing to shrink whole block, but couldn't move the sleeve.
@thebug4046
3 жыл бұрын
Heat the block a bit put a few zip ties in the exhaust port turn the engine over it will Lift the sleeve out of the block enough for you to grab it with your fingers do not use pliers or anything metal against the sleeve as he will damage it
@Silent47
3 жыл бұрын
@@thebug4046 Unfortunately, I don't have the conrod or psiton, only the crank, crankcase with bearings, and sleeve. I'll try heating the block though.
@thebug4046
3 жыл бұрын
@@Silent47 i have a bunch of other videos showing bearings being done including the SH 18
@Silent47
3 жыл бұрын
@@thebug4046 I think we may have misunderstood each other. I have the sleeve stuck in crankcase, and I don't have the conrod+piston to be able to push it out using the zip tie method. Is there another way to get the sleeve out of the crankcase?
@thebug4046
3 жыл бұрын
@@Silent47 ah gotcha just heat up the block and push un the sleeve from underneath using a chop sick or something not metal and it should pop up
@mattschannel1502
Жыл бұрын
My piston sleeve is tight at the bottom aswell as the top? I think it's why my car won't start
@thebug4046
Жыл бұрын
Something is wrong or there is damage. Go to nitro rc enthusiasts group on Facebook and post the problem im in their
@mattschannel1502
Жыл бұрын
@@thebug4046 thanks think il change the out anyway
@thebug4046
Жыл бұрын
@@mattschannel1502 hopefully you find the problem
@sandstau
Жыл бұрын
mine was tight at the top/ I've taken piston out and used t cut polish and now is smooth/ ps I know shit about nitro cars😂
@mattschannel1502
Жыл бұрын
@@sandstau there supposed to be tight at the top there tapered
@Mad_Scientist2052
4 жыл бұрын
Hi there, I am wondering if you ever or is there a way to adapt a three shoe clutch with the SH .18 engines?
@thebug4046
3 жыл бұрын
I'm not sure
@Mad_Scientist2052
3 жыл бұрын
@@thebug4046 I found a way. Thanks for the reply
@thebug4046
3 жыл бұрын
@@Mad_Scientist2052 no problem sorry for the late reply
@Mad_Scientist2052
3 жыл бұрын
@@thebug4046 no worries.
@rcaddictgarage
6 жыл бұрын
👍
@nts323
5 жыл бұрын
Is the SH .18 and the VX .18 the same engine with different cooling heads.
@thebug4046
5 жыл бұрын
Nope they're completely different made by different manufacturers and are not interchangeable whatsoever the s h 18 is actually a better engine though the sh 18 is actually very high quality if you take them apart bronze bushings at both end of the connecting rod really nice machine work things like that the VX is also a good engine but a lot cheaper and cheaply made
@wadevallbona5314
4 жыл бұрын
Thinking about buying one of these for my TMaxx 3.3. Never heard anything about them. Do they last a long time? Whats your opinion? Any info will help
@thebug4046
4 жыл бұрын
Honestly just go with the dynamite 19 it's a direct swap that requires no crankshaft modifications or exhaust modifications that Dynamite 19 is more powerful than a 3.3
@wadevallbona5314
4 жыл бұрын
Awesome man. I appreciate it. Ive had zero luck with the Traxxas engines. I am def going to look into the Dynamite engine. Thanks for taking the time to reply back. I am going to subscribe to your channel. Thanks again
@thebug4046
4 жыл бұрын
@@wadevallbona5314 there is a group on Facebook called Nitro RC enthusiasts join it take your time with a break in process the longer the better don't use Traxxas fuel switch to a good 30% nitro with 9% oil you will have the best luck with that in a very long engine light with lots of performance also don't use the crappy Traxxas plastic pipe get a nice tune aluminum pipe
@comentador2860
4 жыл бұрын
Hi. That sh 18 has a one way bearing inside? So, if I use a rotary drill on it I don't need a external one way? Thanks!
@thebug4046
4 жыл бұрын
Yes the one away bearing is inside the engine but you need the Pole starter cover their to hold the shaft otherwise it will just fly out as soon as you start it and it will break the crankshaft
@comentador2860
4 жыл бұрын
@@thebug4046 I have a electric drill, the back plate and a wand. I think this will do, I hope..
@thebug4046
4 жыл бұрын
@@comentador2860 Yeah it might I'm not sure I would have to see exactly what you're dealing with and it's kind of hard to imagine that over text message
@comentador2860
4 жыл бұрын
@@thebug4046 I have a SH 18 engine from a Vortex SS, a redcat 11003 Drill Start Wand, a common electric drill and the blackplate from redcat 70111t.
@porousorificePilot
2 жыл бұрын
Anyone know if this engine is the same as the XTM . 18?
@thebug4046
2 жыл бұрын
Should be the same.. SH made all the engines for XTM all the part's should be interchangeable
Пікірлер: 84