Your back at a making!! great to see, looks like a fun and light board!
@Nico_GER7
6 жыл бұрын
Would probably be quite expensive to have you make one for me, right?
@iamkian
4 жыл бұрын
Can you please explain what the difference is between carbon sarga and carbon innegra? I would like to try building something like this but the only carbon I can get here in 200g.m2 is kepper, square or aero.
@virus_virus
4 жыл бұрын
carbon sarga is the clasic cosmetic carbon fiber and carbon/ innegra is the mix of both fabrics, innegra gives more impact support
@carelax805
6 жыл бұрын
🇷🇺 👍 Молодец. Только нужна аннотация к видео.
@ВольноеСердце
6 жыл бұрын
Лайк,я тоже наблюдаю за парнями!
@demetrioloddo1341
5 жыл бұрын
What kind of tape do you use to cut with foam cutter?
@virus_virus
5 жыл бұрын
I use a double face tape like this, thanks www.printfile.com/double-sided-tape.aspx
@dolodolo1479
5 жыл бұрын
you make this template ? can u send it here ?
@jpjay1584
6 жыл бұрын
hey! I whish you success with this project. you have awesome stuff so far. one thing, though: an all black board might look nice, but consider to make it (mainly) white. black surfaces in the sun tend to get really hot. damn, I sound like my dad! ; ) hahaa!
@virus_virus
6 жыл бұрын
I use my carbon fiber surfboards only for surfing don´t worry daddy!! haha thanks
@Surfmus
5 жыл бұрын
And that's why vent plug were invented, the so call hot you meant, creates off gassing. Gore-Tex vent plugs takes care of that.
@pennypop408
3 жыл бұрын
Jucsurf look them up
@javierdemousselle8566
5 жыл бұрын
Hi there, 6,8"x 27" and wich is the width of the board in de middle?
@virus_virus
5 жыл бұрын
3,2"
@ליהיימליך
5 жыл бұрын
wow, that's a great video!
@michaelvadney5803
6 жыл бұрын
Curious, why glass over carbon? Thanks
@virus_virus
6 жыл бұрын
with fibeglass over carbon can get better surface and no break the carbon fiber when sanding before final glass, the mix of both fibers work nice in my surfboard, fiberglass give me elasticity and carbon fiber is stronger. And the patches, carbon fiber / innegra give me impact resistance in high pressure areas.
@michaelvadney5803
6 жыл бұрын
That makes sense. Sanding through glass isn't as bad as sanding through the continuous strands of CF. Neat
@carelax805
6 жыл бұрын
Спасибо за аннотацию. 🇷🇺
@Simoooooooonn
6 жыл бұрын
Ohh wow you are sanding carbon without gloves
@virus_virus
6 жыл бұрын
yes every day. I need to feel the shape in my hands, don´t die for this, don´t worry friend
@michaelvadney5803
6 жыл бұрын
Watch out for that. I have some embedded in my hands. Mask is always good when cutting and sanding CF. Another project eh? Thanks!
@virus_virus
6 жыл бұрын
Mask is different than use gloves, I always use mask and you´ll never watch a video on my channel without mask, ok? I have 200 videos you can check. I hope you like my projects, thanks
@santossuarez
4 жыл бұрын
@@virus_virus Gracias por todos tus video. No he encontrado ninguno como los tuyos. Estoy ahora mismo tratando de hacer mi propia table de paddleboard long y esto me va a ayudar 100%. Saludos desde MIami, FL!
@mydc2200
4 жыл бұрын
What kind of foam you used?
@virus_virus
4 жыл бұрын
EPS
@mydc2200
4 жыл бұрын
virus thank you
@mydc2200
4 жыл бұрын
virus do i need to oven after that?
@Karatsv
6 жыл бұрын
Когда вторая часть?
@virus_virus
6 жыл бұрын
2 days
@pquispea
4 жыл бұрын
Good job! I want to ask you about minute 4:30 Is it possible to put those pieces of carbon innegra a layer before? What is the advantage to put them on top? think you can get a uniform surface if you put them a layer before. I have seen others doing the same, but i dont understand why. Thanks
@virus_virus
4 жыл бұрын
the reason is that the innegra fabric is better for impact hits than carbon fiber layer with and must be placed first to absorb the impact of my feets
Пікірлер: 33