Nothing is senseless if it helps you get the job done correctly. I do many things like this just because I want to and it helps me and I could care less if others agree or not. Nice work.
@anthonycalia1317
8 жыл бұрын
I'm not a machinist, but watching and listening to your old-school wisdom is relaxing and informative. I'm certain you were well-loved by your students, and bet you shaped many of their lives and careers. I can just tell...
@johnfry9010
8 жыл бұрын
Nice video and repair , the older we get the more we can appreciate being able to see something clearly !
@garyc5483
8 жыл бұрын
Very informative mrpete. I see no problem whatsoever in making a tool work exactly how you need it to work.Thanks for sharing. regards from the UK
@robertmekemson8178
4 жыл бұрын
This is a great video. It shows the perfectionist attitude towards his work! Everyone should take pride and note this excellent description and instruction. An art that is being lost and needs to be embraced again! This is an excellent project that displays knowledge, skill, focus and finishing. This person intended to fix the micrometer where others would just "Throw it away". What if you didn't have that luxury? The overall goal is to make it better than it was, and after disassembly, cleaning, truing, reassembly and zeroing this micrometer will provide accurate measurements again. I also believe this type of instruction should be reintroduced again in high school, Boys Scouts, FFA, 4H and other organizations.
@mrpete222
4 жыл бұрын
Thank you very much. Everything you said is very true
@MrUbiquitousTech
8 жыл бұрын
Well done Mr. Pete; thanks for sharing! You know, I have never, not once, found any machine tools at a yard sale...
@RGSABloke
8 жыл бұрын
Mr. Pete, informative and relevant as always.
@79121000
8 жыл бұрын
Mr. Pete- Thanks for all of your informative videos! I always learn something even though we are around the same age. Thanks again and please keep it up. Mike Ryan
@stevevogelman3360
4 ай бұрын
You did a great job on that. Also I asked you a question a few months ago about my south bend heavy 10 headstock bearings getting hot. You were right on. It was the take up nut being to tight. Thank you and best wishes friend.
@mrpete222
4 ай бұрын
👍👍
@youbail1
6 жыл бұрын
Great Fix, I have cursed my mikes for years (with no effect)as my vision goes and I have to use magnification. I have now applied your fix, and it's now a joy to play with them again. thank you again.
@mrpete222
6 жыл бұрын
Thank you for watching
@oldpup4810
8 жыл бұрын
They're your tools so you can do what you want with them. :) Getting older now and the eyes aren't what they used to be so I highly agree with the adjustment. Thanks for the video.
@timhyatt9185
8 жыл бұрын
really wish we had yard sales and estate sales in our area like you seem to have in yours - you certain seem to come across a LOT more nice tools than I ever seem to be able to find...... i'm a little envious!
@DonDegidio
8 жыл бұрын
Lyle, I always learn something watching your videos.
@georgemorrison9387
4 жыл бұрын
Hi Mr.Pete! I bought a used Mitutoyo 0-1 mic that had this exact problem, only worse-- 12thou to be exact. Otherwise it was beautiful and by doing a KZitem search I found your remedy for my problem. The nice thing is that one can fine tune a mic with this issue to suit their personal preference. I followed your suggestions and now have a usable instrument that I can read and suits my needs. Thanks! George in Pa
@mrpete222
4 жыл бұрын
👍👍👍
@alphabob8156
3 жыл бұрын
I've got the same issue with my Mitutoyo - disappointed frankly. I just spent a TON of money on a 126-137 0 - 1" thread micrometer, a 126-139 2" - 3" thread micrometer, and a complete set of interchangeable anvils. Purchased good to excellent quality used, but still over $750. I could have purchased the high quality Chinese units with the vernier scale for around $220 for a set of three thread micrometers 0 - 1, 1 - 2, and 2 - 3; AND a complete set of anvils. Hope I "only cry once" with this purchase. Overall, Mitutoyo is my go-to brand so I'm probably going to be satisfied after this tune up. More importantly, Thanks Mr. Pete!
@peterwoodland1952
7 жыл бұрын
I really enjoy all your videos. Fowler tools was located in my hometown of Auburndale, Massachusetts and the founder, Fred Fowler offered me a job in 1962. The job has to repair precision tools and I am not sure why I did not accept the offer. Fortunately I landed a career with AT&T Longlines doing something similar. At the time Fred gave a digital caliper which I still have.
@tombellus8986
8 жыл бұрын
Lyle, just a note ; when I was working on the RR boring wheels to press on the axles we would adjust our inside mic's.oo9 off to machine in the right fit on the wheels. of course those mic's were dedicated to that job. So if that micrometerwas used in a factory they might have been set to make the fit for a shaft/ bearing. Thanks enjoyed!!
@shawnmrfixitlee6478
8 жыл бұрын
I like to see the 0 line as well , Great fix !
@MrShobar
8 жыл бұрын
As I recall, the Lufkin micrometers had a collet that retained the spindle, so this kind of adjustment could be made without the machining operation you've shown. The B&S "slant line" micrometers were developed to avoid the reading problem you've described, but I never liked them.
@iainsmall8880
8 жыл бұрын
+MrShobar Your right,most mics have adjustment in the thimble so you can "zero" them without having to machine them
@therabbitchannel2059
4 жыл бұрын
That's a rebranded NSK mic. I have NSK mics and I like them alot. They aren't collected like some brands so you can get them reasonably priced. SPI also rebranded NSK mics and I own an SPI mechanical digital mic that's made by NSK. I really like NSK instruments. Japanese quality. I have 2 NSK dial indicators, one I got that looks pristine, with a magnetic stand for 35 bucks. I also have an NSK height gauge I got NOS for 110 bucks. I could never get a Starrett NOS for that. It's vernier and has a movable magnifier which I've never seen on any other vernier gauge. Cheers Mr Pete!
@mrpete222
4 жыл бұрын
Thank you for that analysis. I agree that they seem to be very high-quality. But I very seldom run across one
@davidhutson4842
5 жыл бұрын
Your work ethic is perfectly demonstrated every-single time I watch anyone of your videos , and alot of great info.....Thank ya,Sir!!!
@mrpete222
5 жыл бұрын
Thank you very much
@aserta
8 жыл бұрын
What an artsy pun ;) I have a Fowler myself, same issue, so this video is very much appreciated.
@aserta
8 жыл бұрын
Personally when i store my mics i use custom made plastic tips (a little bit of heat forming on some thin plastic sheet) that i've lined with that awesome anti rust paper dipped in oil. Perfect for long term storage, never had a spot of rust on any of my mics.
@CNCDude
8 жыл бұрын
Well, the information alone is well worth far much more than the $5 you spent on the micrometer! Man, I wish we could get stuff like that on our garage sales here down in Texas. Bunch of baby clothes and old toys is all you can hope for...
@RyanWeishalla
8 жыл бұрын
Nice repair. Definitely easier to know for sure that you have reached that line when you can fully see it.
@kgee2111
4 жыл бұрын
Once again, Mr. Pete to the rescue! I had this exact problem and didn’t ‘now how to fix it. Now I do. Live long and prosper Mr. Pete!
@mrpete222
4 жыл бұрын
Thanks
@AmateurRedneckWorkshop
8 жыл бұрын
That is a matter of personal preference and however you want it is the right way. Thanks for the video.
@thomasjake3920
8 жыл бұрын
Wonderfully informative! Thanks Mr Pete.
@johnbazaar8440
8 жыл бұрын
That's a neat trick. I have one that does that. What a pain. Now I know how to fix it. Thanks, John
@karlschwab6437
8 жыл бұрын
Great information and video! My young grandson bought a 5 ~ 6" mitutoyo micrometer at a flea market that was in a wood box. He told me that it turned to tight and took it apart, then he could not get it back together, correctly. I did not realize that there was a spanner wrench to zero it! Now I have the information to see if he has that wrench and the proper gauge blocks. I need the information also, on using the end adjustment and taking it apart. You, as always, have been a great help.
@crosstimbers2
5 жыл бұрын
I like the older Brown and Sharpe Slant Line mikes for ease of reading. You get deeply engraved lines and numbers. The barrel and thimble are satin chrome. The lines and numbers are filled with black ink. When viewed against the satin chrome background there is a lot of visual contrast making the mike easy to read. The Slant Lines are especially easy to read when using a depth mikes since the lines are numbered in reverse order. More recent mikes of many brands have only lightly laser etched lines and numbers making them very hard to read. I collect high grad micrometers. Some times they are terrible to read compared to an ancient set of Reed, Scherr-Tumico or Tubular mike with the deeply engraved lines and numbers.
@lynnjohnson2112
8 жыл бұрын
Art J. Good idea Mr. Pete. Most .025 errors in reading a micrometer are as a result of the zero line being slightly hidden by the end of the thimble. Another great tip! Thanks!
@tinker453
7 жыл бұрын
Hi Mr. Pete. Your skill and attention to detail are splendid! Wonderful video. Thanx
@charlescompton4495
8 жыл бұрын
Great idea and thanks for the instructions, Greg ( a former meticulous arranger of artistic burnt clay products...bricklayer!)
@PeopleAlreadyDidThis
8 жыл бұрын
For mics that you loan out to people, face off .0125. Drive 'em nuts trying to figure out whether they're measuring .250 or .275! I wasn't enthusiastic about this idea until I looked at my Starrett 1-2" a minute ago. Now I think uncovering the line is a great idea. It's a lot better idea than it was 25 years ago.
@aktrapper6126
8 жыл бұрын
Appreciate the tips on how to store a micrometer.
@petek210
8 жыл бұрын
Part of the joy of owning and using tools is modifying them until they work best for you. Someone who's tools are all in pristine condition is someone who never uses their tools.
@larrydurish4321
8 жыл бұрын
I love your videos alys look forward to watching them
@rogermisner3368
2 жыл бұрын
I kept thinking, "Only take .002-.003 off of it" and It turns out that would have been enough, butI like your style... Nice video.
@charlietanner6211
5 жыл бұрын
as usual learn something every video you are one of those teacher,s who should have been paid on merit i bet you have former student,s still thanking you
@Engineerd3d
8 жыл бұрын
So you circumcised a micrometer? Love it Mr Pete. I had teachers like you in HS. A bit cantankerous but so much knowledge to share.
@PierreaSweedieCat
8 жыл бұрын
Fascinating. I knew nothing of any of this. Thanks.
@mikec.1259
8 жыл бұрын
Hey Mr. Pete, Guess what, that's your Mic, and you can do what ever you want to do with it. And I wish I made some trips up in the Heartland to some of your great sales.
@keithburton99
8 жыл бұрын
Excellent idea! Wish I had thought of it before buying digital micrometers because I could not see the lines properly.
@alphabob8156
3 жыл бұрын
Outstanding video! I'm ""wrestling" with the same "zero line covered up" issue. This looks like an easy fix - thank you!
@P61guy61
8 жыл бұрын
as usual, great information. thank you.
@MrSchoessow
8 жыл бұрын
Way to go Mark Polley, now I don't have to say it. Great Video as always mrpete!
@Dabbel2
7 жыл бұрын
Thanks for being there at just the right time. Recently obtained Starrett 2" mic, and the lines on the barrel must be completely covered for the mic to be read, "I hate it when that happens". Could not imagine how to remedy the situation till stumbled across your Video. Thanks again. By the way your sign-off always reminds me of Paul Harvey's sign-off, Thats a good thing.
@mrpete222
7 жыл бұрын
Thanks for watching
@jmh8743
8 жыл бұрын
+10 i have one that is so bad i have count the tick marks. i abhor using it. i think you are spot on mr pete
@Inspironator
8 жыл бұрын
Mr Pete, I personally like to split the hair, and then if the zero doesn't line up, then I can tell something is amiss. But, I just want to say that I'm a wet behind the ears newbie. I don't have a lathe, but I'd like to get one. i really don't know much AT ALL about machining except what I learn from you. I do like your video, as it is good to learn how to machine this shape. Thanks
@DavoShed
5 жыл бұрын
This is exactly what I needed to know. My cheap Indian mic has the lines buried by about 12-15 thou. Ist so annoying I’m concerned I’ll miss measure something by .025” I thought about turning the end of the barrel down but it’s so tight I’m afraid I’ll break something duetting it off. I never thought about turning the thimble back a bit. Now I can turn it into a useable tool Thanks Mr P. ;)
@N.Cognito
8 жыл бұрын
when ever I have that problem the first thing going I do is make sure the barrel is fully seated. most times that fixes the problem. when you reassembled the barrel it was seated better than at first, that's why it went from .007 to .004.
@jeffreylehn8803
8 жыл бұрын
not having the line exposed would drive me nuts also , great fix
@ClownWhisper
6 жыл бұрын
Thanks for the video. It helped me personally a lot thank you Every time you say that to lose lautrec gag I think of my father. He could not say to lose without following it up with lautrec!
@mrpete222
6 жыл бұрын
lol
@JunkMikesWorld
8 жыл бұрын
I always zero mine out to check and see where the thimble lines up. I do like your idea though. I just may tune up my mics one day. Thanks for sharing! All the best! Mike
@MegaLostOne
3 жыл бұрын
I bought a Tumico that I wasn't able to adjust the thimble for calibration, I ended up taking the thimble out and heated it with a hot air gun and that allowed the oil or grease that had hardened to release and I was able to adjust it after that. Just a hint for anyone that runs into that problem.
@mrpete222
3 жыл бұрын
Thanks
@libertarianlife3651
5 жыл бұрын
No argument here, absolutely easier to read. I'm gonna get out my air tools and fix all of mine now ! (just kiddin') I recently bought a Fowler dial bore gauge and am gonna take it back. Browne and Sharpe or Starrett never disappoint me.
@mrpete222
5 жыл бұрын
Thanks yes
@johnjohn-ed9qt
8 жыл бұрын
I've never worried much about where the edge of the thimble made the line, as long as the line is visible. I own mics that run from splitting the mark to full exposure,ad use at work mics that do both, as well. I check the zero each use,because I can't keep track. If I didn't have to use tools that were not in my control, I would probably do what you did for consistency.
@chemech
8 жыл бұрын
It's a matter of personal preference with regards to the relative location of the zero line... I just checked a couple of my micrometers, including my first one, made by Mitutoyo, and they are like the original condition on those Fowler's you modified... The edge of the thimble collar comes from the factory - on some manufacturers' offerings - set to split the little number 0 and the line. I'm fine with that, but if it bugs you, by all means modify your tools to suit your preferences. It's not like a $5 yard sale find is a collector's item after all... at least not in this case! ;^) Regards, Eric
@BluesTheBestBoyIGuess
2 жыл бұрын
The line wasn't hidden though - You could clearly see it. The demonstration was interesting, but it was unnecessary.
@rwallace9848
8 жыл бұрын
Awesome video! Do another myth breakers please!!
@mcnultyfp
8 жыл бұрын
Great idea! I have had an ancient Starrett, with never a problem reading, but lately other brands of micrometer I have are confusing me, and now the penny has dropped. THANKS.
@ke6bnl
8 жыл бұрын
I like that and the old eyes are not as good as they use to be and that is very helpful
@simonaldridge82
8 жыл бұрын
great job I also struggle with the lines on occasion
@erikclausen4780
2 жыл бұрын
Job well done Mr. Pete great information .
@rtertertrryyty
8 жыл бұрын
I liked the video I didn't know of some of the adjustments that were were on it Thanks for the information. This was a great help to me. I also have one that is giving me a fit now it works fine thanks again.
@yannkitson116
8 жыл бұрын
I don't know if I would ever do that, but it was interesting all the same. Mind you I paid a lot more than $5 for my micrometers and it might explain my reluctance ;)
@jaredbaker2339
8 жыл бұрын
really enjoyed learning about a partial line vs a full. Thanks.
@mc_cpu
8 жыл бұрын
I've been unable to set my micrometer to zero as it's too stiff to turn the scale barrel with the little spanner, seeing it's probably just a friction fit gives me confidence to try a little more force on it in the vice (with appropriate protection to try and prevent scratching it). Mine cost £12 approx $17 so not the bargain you got.
@kevCarrico
8 жыл бұрын
another great video - and thank you for the detailed information!
@stefantrethan
8 жыл бұрын
I agree with your closing statement - it was perfect before you messed with it, but it was interesting to see the inside. I'm wondering if there isn't some way to adjust this - otherwise how do they make it so that the micrometer always reads zero on the front, there must be some way to adjust the spindle relative to the thimble.
@HughesEarthworks
8 жыл бұрын
Great video Lyle. I need to do this to one of mine, it has always annoyed me that I would have to go past to verify I was on the correct line.
@infoanorexic
8 жыл бұрын
I've got a trio of Grizzly mic's (not their cheapest) that have proved to be quite consistent, but they also almost bury the line. Now I know what to look for. I hope all it takes is getting the barrel seated a little better in it's socket. If not, well, I now know what my other options are (after the warranty has expired, of course)...
@Satchmoeddie
7 жыл бұрын
There is a name I forgot about. Fowler. Not a big fan of Fowler, but they are better than Chinesium tools. I hate to admit it, but I like Mitutoyo just fine, or SPI. Starrette is the old American made standard. The Japanese electric guitars rival American guitars in price, and usually exceed them in quality now. Is that the same Mauser that made the Mauser 1898 rifle? I need another 24" deep 2" micrometer. Those get sprung pretty easily. I think I'd use a small Arkansas stone rather than the file, but it's your shop! God bless you, Mr Pete!
@backyardmechanic921
8 жыл бұрын
I've got a one inch Starret it doesn't have any corrosion like yours. I like the old tools better than the new stuff.
@jjbailey01
5 жыл бұрын
Perhaps you didn't need to modify the thimble. But anything you can do to help make your tools work for you instead of against you should be seen as a necessity. Especially in this day and age. Thanks for the video. I just bought a cheapo Amazon 0-6" set of vernier mics. I think I'm confident enough now to tune them up nice enough for the occasional work that I do that requires a modest amount of precision. Maybe one day I'll get gifted some nice Starrets. I just don't use them enough to warrant the cash spent on nice things. That, and I've developed a knack for getting cheap things to do what I need. Which in this case is basically an adjustable go/no-go gauge for deciding which parts go to the machine shop and which parts go to the scrap heap.
@gadget73
8 жыл бұрын
Looks like a Mitutoyo mic. Wonder if thats who was making them for Fowler at that time.
@felixcosty
8 жыл бұрын
I liked the video and I agree with you on where the line is, my 1 inch mitutoyo mic does the same thing it splits the line I find this a problem when you try to read the 25 50 and 75 marks.
@jmegown52302
4 жыл бұрын
This explains a Starrett No. 209 marked Autocar Co. that I picked up off of eBay. The front edge of the barrel is trimmed down such that the edge of the adjustment notch is open and the very bottom of the numbers are gone.
@dragman377
6 жыл бұрын
I kind of like to see that line also. Good video Mr. Pete.
@mrpete222
6 жыл бұрын
🤙
@TechGorilla1987
7 жыл бұрын
My opinion is that this it the height of detail and why a good portion of the people watch your productions.
@mrpete222
7 жыл бұрын
Thanks for watching.
@CraftedChannel
8 жыл бұрын
Do some micrometers allow for movement (adjustment) of the anvil within the thimble? If it could be moved this same adjustment could be accomplished. Don't worry about complainers. All of human accomplishment depends on the alteration of the earth and it's contents to suit our individual choices. Those who value stock settings above usefulness are under some misguided illusion their gear will be desirable for museum display some day. It won't. Thanks for the great content!
@briancrane7634
4 жыл бұрын
Most machinists want the thimble to "divide the line in half" or "split the line" to take their measurements. This instrument was apparently used in a factory for inspection work they did not need to modify it. But it's yours so to each his own...
@bentontool
8 жыл бұрын
I learned a lot! Thanks...
@WalkerKlondyke
8 жыл бұрын
I did the math on the 40tpi. He's right.
@helenhoney7167
5 жыл бұрын
On a Measumax micrometer this is adjustable once you separate the thimble from the spindle taper.
@RambozoClown
8 жыл бұрын
Much easier to read when you can see the lines clearly.
@elsdp-4560
8 жыл бұрын
THANK YOU...for sharing.
@DATo_DATonian
5 жыл бұрын
Developing your "feel". - No matter how great the quality of your mic or its age or brand, it all comes down to YOU in the final analysis. Many people buy expensive instruments but do not know how to use them properly. Most important when using a micrometer is knowing how much pressure to exert on the part being measured. Now some mics have "slip thimbles" or ratcheting knobs to limit the amount of pressure being exerted; however, it would behoove you to learn to develop a "feel" for those times when these crutches are not available, because they are NOT always available on every mic. I am a retired machinist of 50 years in the trade and I never knew a seasoned machinist who used a ratchet or slip thimble when taking measurements. The way to develop a "feel" is to pick some idle time such as lunch break or when you are watching TV at home and repeatedly attempt to take a mic reading. With a 1" mic simply closing it down to the anvil would be fine. The important thing is DO NOT LOOK AT THE MIC'S SCALE WHEN YOU ARE DOING THIS. Your mind can trick you into exerting more or less force to get the lines to coincide if you are looking at it. Take the reading repeatedly many (50 -100) times without looking at it. Do not fear, you don't have to do this forever only until you develop your feel. It's like learning to swim or riding a bike, once developed it will stay with you for the rest of your life. After feeling the mic's contact surfaces meet to the extent that you think the pressure you are exerting is correct THEN look at it after each attempt. At this point you don't care what the reading is, only that it is consistently the same. With larger mics you will need a standard or Jo Block. Ask at work if you can borrow one or two overnight. When you are convinced that you can hit EXACTLY at the same point within a tenth (even if only estimated for mics which do not have tenth graduations) then adjust the mic such that the lines are accurately set. The mic is now set to YOUR feel. Another machinist may get a different reading just as you might if using his mic. In the long run this is far more important than the do-dads which come with the mic for this purpose because this same exercise can be used on depth mics, height gages, telescoping gages etc. Hope this proves to be of use to some of you. EDITED TO ADD: If you CANNOT get the mic to repeat after many many conscientious attempts perhaps the mic is junk ... the problem may not be with you. When buying used mics if your feel is developed you will be able to sort the good ones from the junk because your feel, having been developed, will be a reliable constant - if the mic won't repeat to your feel after taking multiple readings don't buy it. Remember - it doesn't have to have the lines in alignment (it can be adjusted) but it DOES have to hit at EXACTLY the same place EVERY time.
@mrpete222
5 жыл бұрын
Thank you for a great analysis and good advice for them all very true
@DATo_DATonian
5 жыл бұрын
@@mrpete222 You got a good channel Petey. I used to teach machine shop too and in my opinion, judging from what I've seen in your videos, your technique is spot on perfect. Believe it or not we actually had one of those things you showed in your last "What is it?" video (42a) - the thing in the box. I don't remember what it was for though. We inherited it from past generations. I do remember that it's function was of little to no value to anyone living or dead. For the life of me I couldn't figure out why they bought it. Maybe they got it for nothing. Like I said I don't remember what it's function was but I've been racking my brain to remember. I'm looking forward to your "Answer" (42b) video.
@RollingEasy
8 жыл бұрын
Totally off this subject MrPete, you as someone with many years of experience and knowledge might be able to answer just how effective is 'Balancing' (damping perhaps), drive shafts with an amount of oil added via a drill hole and then plugged? I've heard of this for decades. Could it reduce vibration if used as a 'poor man's' balance?
@VEMWMIKE
8 жыл бұрын
+Tom Tee That might sound good in theory but in a vehicle it might only balance 1 end being lower. The only "poor man's way" that I have seen has been hose clamps at each end but it takes a while to find the sweet spot. Balancing machines these days can balance single and 2 piece drive lines to less than .5 grams.
@georgecrutchfield8734
7 жыл бұрын
Thank You, Mr Pete!
@Landrew0
8 жыл бұрын
100,000 subscribers. YeeHaw!
@Robonthemoor
6 жыл бұрын
I like the line has well young mr 222 💥
@mrpete222
6 жыл бұрын
🤙
@sqisherking1
8 жыл бұрын
"If it's Toulouse... Lautrec" ;-)
@randelljones4002
5 жыл бұрын
Mr Pete that is a spline micrometer used for measuring spline roots on shafts
@mrpete222
5 жыл бұрын
Thanks
@bobb348
8 жыл бұрын
mrpete22 it is your tool and you can skinner back how ever you like tubalcain
@emildekoven4872
8 жыл бұрын
Good show! Very informative and transparent..... I suppose this ILK of micrometer is now disdained in favour of those with digital readouts....?
@JDSly1
5 жыл бұрын
Good job. Sadly, on many B&S micrometers, the graduations are stamped very lightly on the thimble and barrel, making them difficult to read with nothing that can be done to correct the problem. Sold mine and bought a set of Mitutoyo's.
@mrpete222
5 жыл бұрын
👍👍
@3markaw
4 жыл бұрын
I've easily corrected issues like this with a little black paint brushed on then wiped off leaving the markings clearly visible. Saves a lot vs buying new.
@kgee2111
4 жыл бұрын
M Williams I wonder if Dyekem will also work? I have this problem.
@kevinwillis9126
8 жыл бұрын
Thank you for sharing sir....
@Patroand
8 жыл бұрын
Great! I have one to repair. Thanks
@doorguru168888
6 жыл бұрын
No doubt about it, the line is more visible.
@mrpete222
6 жыл бұрын
Thanks
@aliahmadbilal666
5 жыл бұрын
Great video . I used to have thw same problem . I know how to solve it now . Many thanks .
Пікірлер: 191